Pin board glass display

UNO R3 ATmega328P Board: Description: UNO R3 board is 100% compatible with original Arduino, now it has perfect quality and performance. Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements theProcessing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux). This is the new Tosduino Uno R3. In addition to all the features of the previous board, the Uno R3 now uses an ATmega16U2 instead of the ATmega8U2 chip. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. Note: The TOSduino Uno R3 requires the Arduino 1.0 drivers folder in order to install properly on some computers. We have tested and confirmed that the R3 can be programmed in older versions of the IDE. However, the first time using the R3 on a new computer, you will need to have Arduino 1.0 installed on that machine. The small chip is ATmega16U2, the 28 pin DIP socket chip is ATmega328-pu. 2.8 Inch LCD Display Feature: Description: 2.8 inch LCD TFT display Bright, 4 white-LED backlight Colorful, 18-bit 262,000 different shades 4-wire resistive touchscreen 240 x 320 pixels with individual pixel control No wiring, no soldering. Simply plug it in and load library On-board 3.3V 300mA LDO regulator 5V compatible, use with 3.3V or 5V logic Support 2GB micro SD TF card Size: 7.8 x 5.3cm Package included: 1 x 2.8 Inch TFT LCD Shield Touch Display Module 1 x UNO R3 ATmega328P Board with USB cable

Arduino Starter Kit     Please check shipping information before placing an order   General   Compatible with Arduino High quality Board: UNO R3   Package Contents   Arduino UNO R3 Board 400 point Breadboard USB Cable 9V Wall Power Adapter (1A) Remote control for Ardunio 1602 LCD Ardunio Protosheild w/ Mini Breadboard 65 X MM Jumper Wires (assorted length) 4 Pin DuPont Wires SG90 9G Servo Stepper Motor Stepper Motor Driver 100 x Resistors (10 each / 10, 100, 200, 330, 1K, 2K, 5K, 10K, 100K, 1m ohm) 9V Battery 1 Channel Relay Module 8*8 Dot Matrix Module 7 Segment Display (4 digit) 7 Segment Display (1 digit) MPU 6050 Accelerometer and Gyroscope Module XY Joystick Module HCSR04 Ultrasonic Sensor Module Small Plastic Box (with components) 5 x BC547 NPN Transistor 5 x BC557 PNP Transistor 2 x Photoresistor (LDR) 5 x 1N4007 Diodes 5mm LED (5 each / blue, green, yellow, white, red) RGB LED (Common Cathode) 2 x 10K Potentiometer 74HC595 8 Bit Shift Register MAX7219 Chip (LED Driver) Thermistor Piezo Buzzer 5 x 22pF Capacitors 5 x 0.1uF Capacitors 2 x 50V 10uF Capacitors 2 x 50V 100uF Capacitors 5 x Push Button Switches H-Bridge Motor Driver IR Receiver 3V DC Motor 5 x PN2222 Transistors Breadboard Holder 40 PIN Header            

Functional Overview CPU Allwinner V3S, ARM Cortex-A7, up to 1.2GHz Memory and storage Integrated 64MB DDR2 Reserved SOP8 SPI Flash pad (customizable patch 8~32MB SPI Nor Flash, 128MB Nand Flash) Onboard half-slot TF card holder, can be started by TF display Universal 40P RGB LCD FPC Socket Can be directly inserted into the common 40P 4.3/5/7 inch screen (onboard backlight driver), through the adapter board can be inserted 50P 7/9 inch screen Support common 272x480, 480x800, 1024x600 and other resolutions On-board resistive touch screen chip supporting resistive screen Onboard RGB LED Communication Interface SDIO x2, can be used with the SDIO WiFi+BT module SPI x1, I2C x2, UART x3 100M Ether x1 (with EPHY) OTG USB x1 MIPI CSI x1 Other interface PWM x2 LRADC x1 Speakerx2 + Mic x1 Electrical characteristics Micro USB 5V power supply; 2.54mm pin 3.3V~5V power supply; 1.27mm stamp hole power supply Output 3.3V and 3.0V (AVCC), optional input RTC voltage 1GHz linux no-load running current 90~100mA, full load running current ~180mA Storage temperature -40~125°C, operating temperature -20~70°C Software function: Support linux 3.4 bsp kernel, linux 4.16 mainline kernel Support Qt, python and other common linux applications Size and weight Core board size 25.4x45.0mm Development board size 47.0x47.0mm Core board weight 5.0±0.1g Development board weight 14.5±0.5g Precautions start up Zeros requires the card to start (or solder SPI flash), only plug in the USB without any phenomenon System debug serial port UART0, specific position reference pin diagram USB interface OTG usb, power and communication Bottom debugging It is recommended to use usb to serial port small board to connect "U0T R" and "G 5V" Operating temperature -20~85??/span> Running current Running Linux no-load current is about 100mA, full load current is about 150~180mA, and LCD current is about 200~300mA. No card power-on current is about 50~60mA Reference info. (Can click for more detail): 1. Document 2. Github 3. BBS 4. Wiki 5. E-mail: support@sipeed.com Package Included: 1x Lichee pi board 1x Plug 2x Pins

Geekcreit™ UNO R3 ATmega328P Board + 2.4 Inch TFT LCD Touch Screen Module For Arduino Note: The 2.4 inch LCD Touch Screen Module is the newest version which has more stable chip with touch pen. (Update in 2015-09-17, CN warehouse at present) Please pay close attention to the bottom of the forum, we will post the most newest driver there, if your LCD screen can not work, please contact us to get the useful driver, thank you! UNO R3 ATmega328P Board: Description: UNO R3 board is 100% compatible with original Arduino, now it has perfect quality and performance. Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements theProcessing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux). This is the new Tosduino Uno R3. In addition to all the features of the previous board, the Uno R3 now uses an ATmega16U2 instead of the ATmega8U2 chip. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. Note: The TOSduino Uno R3 requires the Arduino 1.0 drivers folder in order to install properly on some computers. We have tested and confirmed that the R3 can be programmed in older versions of the IDE. However, the first time using the R3 on a new computer, you will need to have Arduino 1.0 installed on that machine. The small chip is ATmega16U2, the 28 pin DIP socket chip is ATmega328-pu. Interaction: 2013-08-08 Cathal Keady's question: Can item SKU066313 be powered directly from using the USB port or do I need to purchase a power supply for it. my answer: This item has not built-in battery, so it can not be charged. With that USB cable connect to computer, you can use it. There is no need of power supply. 2.4 Inch TFT LCD Touch Screen Module: Features: 2.4 inch LCD TFT display Colorful, 18-bit 262,000 different shades 4-wire resistive touchscreen 240 x 320 resolution Spfd5408 controller with built in video RAM buffer 8 bit digital interface, plus 4 control lines Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3 and analog 4 and 5. Pin 12 is available if not using the micro SD 5V compatible, use with 3.3V or 5V logic Size: 71 x 52 x 7mm Package included: 1 x UNO R3 ATmega328P Board with USB 1 x 2.4 Inch TFT LCD Touch Screen Module with touch pen

(←please click here) (Due to the different batch,These board have two colors, Bule or Green, will be send in random, please note that before you buy it !!!) Suitable case: Parameter: LCD Type TFT LCD Interface SPI Touch Screen Type Resistive Touch Screen Controller XPT2046 Colors 65536 Backlight LED Resolution 320*480 (Pixel) Aspect Ratio 8:5 Power Consumption TBD Backlight Current TBD Operating Temp. (Centigrade) TBD Interface Definition: PIN NO. SYMBOL DESCRIPTION 1, 17 3.3V Power positive (3.3V power input) 2, 4 5V Power positive (5V power input) 3, 5, 7, 8, 10, 12, 13, 15, 16 NC NC 6, 9, 14, 20, 25 GND Ground 11 TP_IRQ Touch Panel interrupt, low level while the Touch Panel detects touching 18 LCD_RS Instruction/Data Register selection 19 LCD_SI / TP_SI SPI data input of LCD/Touch Panel 21 TP_SO SPI data output of Touch Panel 22 RST Reset 23 LCD_SCK / TP_SCK SPI clock of LCD/Touch Panel 24 LCD_CS LCD chip selection, low active 26 TP_CS Touch Panel chip selection, low active   Package included: 1 x 3.5 Inch 320 X 480 TFT LCD Display Touch Board

3.2 Inch 320 X 480 TFT LCD Display Module Support Arduino Mega2560 Description: 3.2 Inch TFT LCD with 262K color 480x 320 resolutions.The controller of this LCD module is HX8357B, it supports 16-wires DataBus interface.Moreover, this module includes the 5V-3.3V power conversion circuit and Level conversion circuit, This Module can Directly inserted into the Arduino Mega2560 Board,it also includes the SD card socket and SPI FLASH circuit Feature: Support Arduino Mega2560 Directly inserted With Full-angle IPS TFT panel OnBorad level conversion chip for 5V/3.3V MCU Compatible with 3.3/5V operation voltage level Compatible with Arduino-Series development Board. (Please notice:This Screen is not touch screen) Provided 12-examples with Arduino,3-examples with STM32 With SD Card Socket With SPI FLASH circuit Parameter:   Display Type:  3.2 inch a-si TFT LCD Module Glass Type:  TFT IPS(Full-Angle) Display Resolution:  480 X RGB X 320 Pixels Back light:  6 chip HighLight white LEDs Control IC:  ILI9481 Interface:  16Bit parallel interface PCB Module size:  89.92mm X 54.25mm LCD Area(WxHxT):  50.74mm X 78.35mm X 1.88mm Active Area(WxH):  67.68mm X 45.12mm   Package included: 1 x 3.2 Inch LCD Display Module  

3.2 Inch 320 X 480 TFT LCD Display Module Support Arduino Mega2560 Description: 3.2 Inch TFT LCD with 262K color 480x 320 resolutions.The controller of this LCD module is HX8357B, it supports 16-wires DataBus interface.Moreover, this module includes the 5V-3.3V power conversion circuit and Level conversion circuit, This Module can Directly inserted into the Arduino Mega2560 Board,it also includes the SD card socket and SPI FLASH circuit Firmware link!!! Feature: Support Arduino Mega2560 Directly inserted With Full-angle IPS TFT panel OnBorad level conversion chip for 5V/3.3V MCU Compatible with 3.3/5V operation voltage level Compatible with Arduino-Series development Board. (Please notice:This Screen is not touch screen) Provided 12-examples with Arduino,3-examples with STM32 With SD Card Socket With SPI FLASH circuit Parameter:   Display Type:  3.2 inch a-si TFT LCD Module Glass Type:  TFT IPS(Full-Angle) Display Resolution:  480 X RGB X 320 Pixels Back light:  6 chip HighLight white LEDs Control IC:  ILI9481 Interface:  16Bit parallel interface PCB Module size:  89.92mm X 54.25mm LCD Area(WxHxT):  50.74mm X 78.35mm X 1.88mm Active Area(WxH):  67.68mm X 45.12mm   Package included: 1 x 3.2 Inch LCD Display Module  

W03 4 inch Car HUD Head Up Display with OBD Interface LED Functional Characteristics:  1.  OBD cable connection.  2.  Outstanding definition by using white light LED    3.  Common USB port good for software upgrade  4.  Great for reading with accurate big screen  5.  Multiple function display and automatic power on & off  6.  Time display function    7.  Real humanity speaking and reminding  8.  Time recording of driving and parking  9.  Auto adjusting the brightness when light source changing 10. Auto matching the parameter when starting the vehicles. How to Install:   1. Place the mat to the front desk of the diver under the front windshield with adhesive surface. 2. Place the HUD on the mat, adjust the view angle and position and make sure your vision clear. 3. Connect the OBD cable with vehicle OBD16 diagnostic port. 4. Connect OBD 12 pin USB port with the host,when the host was powered on, the setting icon will light on. 5. Start the car, then HUD power on, system will play the voice at the same time, monitoring data output.    How to Work:   It is using optical reflection principle, reflect the important driving data to the front glass of the vehicle. This device are placed under the windscreen of the vehicle, via OBD cable to receive the vehicle ECU data, timely and accurate read the speed/rotation speed/fuel data and so on. Then, project it onto the front windshield so that drivers no need to look down and can be read real time! This device greatly improve the security and practicability. Because of this, when our HUD are put on sale it will got positive feedback. Technical Indicators: 1. Working Conditions:    Ambient Temperature - 20 degrees to + 80 degrees    Relative Humidity 10%- 95%       Environmental Noise ≤ 60 db (A) 2. Alarm Sound Level ≥ 30 db (A) 3. Working Voltage: 5 v / 1.2 A 4. Voice Reminding ContentSpeed/Gear-change lever /Fatigue/Engine temperature/battery 5. Display Content: Voice/Speed/Engine rotational speed/Idle speed and instantaneous Fule consumption/Engine temperature/battery voltage/Clock 6. Product Size, Host: 106 x68x18. 5 mm 7. Product Weight: 95 g Package Included: 1 X W03 Head Up Display 1 X OBD Line

Description: The IIC 2004 LCD display module is a 4 line 20 character LCD module not only set the contrast control knob selector switch also has a backlight and IIC communication interface. For Arduino beginners, not for the cumbersome and complex LCD driver circuit connection and a headache, the real significance of this LCD module will simplify the circuit, this module directly into the Arduino Sensor Shield V5.0 sensor expansion board IIC device interface can, GM 4P sensor connection cable, programmed through the Arduino controller, you can easily identify the slogan, sensor data records. Specification: Display: yellow green Supply voltage: 5V Interface: I2C I2C address: 0x27 or 0x3F random delivery Pin definition: GND, VCC, SDA, SCL Contrast adjust: potentiometer Display format: 20 Characters x 4 lines Adjustable backlight The module can be easily interfaced with a MCU Fully assembled and tested serial LCD 20 x 4 module The module is a low-power consumption character LCD module with a built-in controller It is fantastic for Arduino based project Size: 9.8 x 6 x 1.2mm Package included: 3 x 2004 LCD display module

Feature: To avoid the problem that the screen can not display, GPIO5, as the NSS pin of the LoRa module, needs to be pulled up when the system is initialized. pinMode(5,OUTPUT); digitalWrite(5,HIGH); m5.begin(); Package included: 1 x M5Stack LoRa Module SX1276 LoRa 433MHz Wireless Board Built-in Antenna IOT Development Board

Description: The IIC 2004 LCD display module is a 4 line 20 character LCD module not only set the contrast control knob selector switch also has a backlight and IIC communication interface. For Arduino beginners, not for the cumbersome and complex LCD driver circuit connection and a headache, the real significance of this LCD module will simplify the circuit, this module directly into the Arduino Sensor Shield V5.0 sensor expansion board IIC device interface can, GM 4P sensor connection cable, programmed through the Arduino controller, you can easily identify the slogan, sensor data records. Specification: Supply voltage: 5V Interface: I2C I2C address: 0x27 or 0x3F Pin definition: GND, VCC, SDA, SCL Contrast adjust: potentiometer The module is a low-power consumption character LCD module with a built-in controller The module can be easily interfaced with a MCU Display format: 20 Characters x 4 lines Fully assembled and tested serial LCD 20 x 4 module White text, blue backlight It is fantastic for Arduino based project Size: 9.8 x 6 x 1.2mm Package included: 3 x 2004 LCD display module

Description: The IIC 2004 LCD display module is a 4 line 20 character LCD module not only set the contrast control knob selector switch also has a backlight and IIC communication interface. For Arduino beginners, not for the cumbersome and complex LCD driver circuit connection and a headache, the real significance of this LCD module will simplify the circuit, this module directly into the Arduino Sensor Shield V5.0 sensor expansion board IIC device interface can, GM 4P sensor connection cable, programmed through the Arduino controller, you can easily identify the slogan, sensor data records. Specification: Supply voltage: 5V Interface: I2C I2C address: 0x27 or 0x3F Pin definition: GND, VCC, SDA, SCL Contrast adjust: potentiometer The module is a low-power consumption character LCD module with a built-in controller The module can be easily interfaced with a MCU Display format: 20 Characters x 4 lines Fully assembled and tested serial LCD 20 x 4 module White text, blue backlight It is fantastic for Arduino based project Size: 9.8 x 6 x 1.2mm Package included: 1 x 2004 LCD display module

LED DOT MATRIX DISPLAY MODULE 16x16 51 UNLIMITED CASCADING 12864 DEVELOPMENT BOARD COMPATIBLE INTERFACE; RED PCB.

Please refer to Lantis Electronics website for current and up to date pricing www.lantis.co.za Courier options available for online orders LCD 2.4 inch TFT screen for Arduino UNO R3 Board with gif Touch pen Features: 2.4 inch LCD TFT display Colourful, 18-bit 262,000 different shades 4-wire resistive touchscreen 240 x 320 resolution Spfd5408 controller with built in video RAM buffer 8 bit digital interface, plus 4 control lines Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3 and analog 4 and 5. Pin 12 is available if not using the micro SD 5V compatible, use with 3.3V or 5V logic Size: 71 x 52 x 7mm

Description: Multi-functional transistor tester for automatic detection of NPN and PNP transistors, N channel, P channel, MOSFET and JFET, diodes, dual diode, thyristor, automatic identification of the transistor pinout. It also can be used for frequency measurement and PWM signal generator. Features: 1. The processor uses high performance single chip ATmega328 and using external 8MHz oscillator as the system clock. 2. 1.8 Inch LCD screen, resolution is 128X160, Support 65536 colors. 3. Single button operation, support for automatic shutdown to reduce power consumption. 4. Power supply support battery, the current is less than 20nA when the system is turned off. 5. Measurement time of about 2S each time. Measuring time becomes longer when measuring capacitance or inductance. 6. Detection of NPN or PNP Bipolar Transistor automatic, N channel, P channel MOSFET and JFET, diode, Double diode, P-IGPT, Thyristor, Double thyristor etc. For some thyristor and double thyristor. Unable to test When the transistor tester can not meet the requirements of its trigger current and keep the current. Transistor testers are also unable to test the IGPT drive voltages is over than 5V. 7. Support identification pin for test element. 8. Support test current amplification factor for bipolar transistor and base emitter turn-on voltage. 9. Can judge Darlington transistor through the turn-on voltage and the current amplification factor. 10. Support test the gate threshold voltage of MOSFET, grid capacitance and drain electrode in the case of 5V gate voltage- source resistance RDSon 11. Supports the simultaneous measurement of two resistors,Data is four decimal format display. Support potentiometer test, It can not distinguish between the middle pin and this pin When the potentiometer is adjusted to one end of the potentiometer. 12. Minimum resistance resolution 0.01 ohm, Maximum resistance 50M ohms. 13. Can measure a capacitor, Capacitance range 25pf~100mF, Resolution 1pF. 14. Capacitance less than 25pF can be measured by parallel connection another known capacitor is greater than or equal to 25pF. The measured capacitance value can be obtained by subtracting the known capacitance value from the result. 15. When the test capacitance is greater than 90nF, it series equivalent resistance is also be shown, resolution is 0.01 ohm. 16. When the test capacitance is greater than 5000pF. Voltage loss after the test pulse is can be measured.This parameter can estimate the quality factor of the capacitor. 17. Support two diodes to be measured simultaneously and display voltage drop for diode. 18. LED will be identified as a diode, the test voltage drop is much larger than that of the common diode. Two colors diodes are identified as two diodes. 19. Resistance less than 2100 ohm, it’s equivalent inductance is also measured at the same time. Range is 0.01mH~20H, but it’s measurement accuracy is not very good. 20. Program tape self checking function, support calibration of multiple parameters. 21. Support frequency measurement function,frequency signal input from PD4 pin. Frequency resolution is 1Hz when the input frequency is greater than 25KHz. When the value is less than that, by measuring the period, the frequency resolution can be 0.001Hz. 22. Support frequency generator function, output by TP2, the output frequency range is 1Hz ~ 2MHz. 23. Support a fixed frequency signal output from the TP2, the duty cycle can be adjusted by the button. Notice: Before measuring capacitance, the capacitor must be discharged, otherwise very likely damage the meter. Be sure to disconnect the power from the circuit board when testing the components on the circuit board, the test equipment have residual voltage is not allowed. Specifications: Type: Assembled Tester Display: 1.8inch 160*128 LCD Power supply: DC 7-12V Current: Approx. 20mA Resistance measurement: Max. 50MΩ Resistance resolution: 0.01Ω Capacitance measurement: 25pF~100mF Capacitance resolution: 1pF Inductance measurement: 0.01mH~20H PCB size: 7.5 x 6cm / 2.95 x 2.36in Product weight: 50g / 1.79oz Package size: Approx. 10 x 7 x 2cm / 3.94 x 2.75 x 0.8in Package weight: 53g / 1.9oz Package includes: 1 x Transistor Tester English User Manual: Click to open