Parallel kit

Buy RCT AXPERT KING 5KVA RACK MOUNT WITH PARALLEL KIT for R14,770.00

Description Parallel Connection Kit | Parallel / Power Inverter Connection Kit Voltronic Power Inverter Parallel Connection Kit with 2 Operation Modes. Parallel Board, Parallel Communication Cable and Current Sharing Cable included in Kit Overview This inverter can be used in parallel with two different operation modes. Parallel operation in single phase with up to 4 units.The supported maximum output power is 16KW/20KVA. Three units work together to support three-phase equipment, one inverter per phase. The supported maximum output power is 12KW/15KVA. Specifications Contents Parallel Board Parallel Communication Cable Current Sharing Cable More Information View More Information More Products View More Products

Technical Parameters: Product Name: Modified sine wave inverter change pure sine wave rear plate Input voltage: DC380V. Input voltage: AC16V. Output voltage: AC220V. Output frequency: 50 / 60HZ (adjustable) Output waveform: pure sine wave. PCB Specifications: 165X100X50MM. 2000W using power tube: 4 / 47N60 Instructions: Product are modified wave inverter charge sine wave inverter, can make modified wave inverter 2000W, etc..., as modified pure sine wave inverter.First, remove the power tube after correction inverter, and then look at the correction inverter have how many transformers, look at the transformer secondary circuit is connected in parallel or in series, and then add the transformer parameters, modified wave transformer secondary is parallel, In each transformer secondary plus 16 laps. The secondary of the modified transformer is a series type, plus 8 laps per transformer secondary. Then in the correction transformer which transformer one empty foot plus a small voltage parameter, the small voltage parameters using 0.6 copper wire, in the transformer inside around: 5 laps, the small voltage is linked AC: 16V position. (Note: Do not open the magnetic ring when the add transformer with the parameters) After the addition of transformer parameters, we must correct the modified wave inverter high voltage capacitors in exchange for 220UF / 450V, Remember: modified wave inverter high-voltage capacitor has a positive feedback Resistance, the resistance is a few hundred K, but also need to change a large resistance, or the voltage will not rise. After testing the voltage of high-voltage capacitor (positive/negative) voltage is DC380V, the test voltage is normal, the use of cable to the sine wave after the board, after the board output voltage: AC220V / 50HZ, the output waveform: pure sine wave. Package included: 1 x DIY 2000W Pure Sine Wave Inverter Rear Plate Kit

CNC Kit 4 Axis for NEMA 17/23 Product Description This is the CNC Kit 4 Axis for NEMA 17/23. It can also be used for NEMA 34 however recommended for 17/23. This Kit is also equipped with the latest 5 Axis Breakout Board. It also comes with the Stepper Driver 5A. Please confirm availability. Please contact us should you require full specs. This kit is suitable to work with the Stepper Motor - NEMA 23 Package Contents 4 x 1 Axis TB6600HG Microstep Driver Board (TB1H) 1 x 5 Axis Breakout Board 1 x DB25 LPT Parallel Cable 1 x USB Power Cable 1 x CD Driver

Contents: 2x 7'6" VR lighthouse stands, 2x tripod mini ball head mounts, 1x equipment carrying case VR Compatible: Ideal for pairing with the HTC Vive and Oculus Rift sensors for temporary or permanent gaming set-ups Adjustable Positioning: Swivel mount devices and move your tripods without the hassle of wall-mounting Compact: Quickly and easily fold up equipment for efficient storage Stable Mounting Solution: For maximum stability, keep tripod leg supports parallel to the ground Product Overview The StudioPRO Set of Two 7'6" Photo Video Light Stands w/Ball Head Mount is the perfect kit for setting up your HTC Vive. The Vive Base Stations need to be positioned at least 6 feet high, face each other, and stand pointed toward your "play area". With this kit, you will not have to mount the base stations directly onto your wall. Instead, you can easily set them up and move them around with the two light stands. The mini ball head mount operates with an adjustable swivel bracket, enabling you to pivot and turn the base stations any direction. The ball head mount can also attach to your DSLR camera, and be mounted onto tripods and monopods for photography or videography. This kit also includes a light weight carrying bag for traveling or storage when not in use. The foam padded walls help protect your equipment from becoming damaged. This bag makes it possible to pack up your play area or studio anytime, anywhere. Note: VR electronics sold separately. Technical Specs SKU: SP50-006 Item: StudioPRO 7'6" Professional Quality Adjustable Studio Light Stand Height: Adjustable from 29 - 76" Weight: 3.4 lb Able to hold up to 11 lb Closed Length: 28 Stem: 5/8 Stem Screw: 1/4" Footprint: 2'4" Base Tube Diameter: 1 Die Cast Aluminum Construction Slip-Resistant Rubber Tipped Legs Black,Non-Glare Finish Quick Release Levers for Smooth Height Adjustments SKU: SP60-002 Item: Lighting Equipment Carrying Bag Dimensions: 30" x 8" x 6" External mesh pocket Easy-to-use strap SKU: SP52-004 Item: StudioPRO Tripod Mini Ball Head Mount for DSLR Camera 360 Swivel Bracket Dimensions: 1.5"x 1.5"x 2" Weight: 0.2 lb Screw Mount: 1/4" Thread: 3/8" Contents 2x 7'6" Studio Light Stands 1x Equipment Carrying Bag 2x Tripod Mini Ball Head Mounts

SONIFEX - NET-LOG- IDE Sata Conversion Kit This IDE to SATA Drive Adapter Kit offers a simple way to install Serial ATA hard drives using an available IDE port - a cost-effective solution for using newer SATA drives on a legacy computer or a computer with all SATA connections already in use. This dual channel bridge lets you connect two high-speed SATA drives without the cost and effort of upgrading your IDE (Parallel ATA) motherboard, while minimizing the space required for IDE cable connections - helping to improve airflow within the case which in turn helps to optimize system performance. Plus, the IDE to SATA Drive Motherboard Adapter includes a power connector and SATA data cables, to ensure the upgrade to SATA is easy!

PIC PIC16 PIC16F877A Development Board Core-Board Kit With 13 Modules Description: The PIC development board Open16F877A is based on PIC16F877A, with rich expansion interface, support all kinds of peripheral modules. Feature: Specification of PIC16F877A: Kernel: PIC 8-bit RISC Operating Frequency: 20MHz Max Operating Voltage: 2V ~ 5.5V Encapsulation: DIP40; I / O ports: 33; Flash: 14kB RAM: 368B EEPROM: 256B Interface: 1 x MSSP (SPI/I2C), 1 x A / E / UART, 2 x PWM, 8 x ADC Debugging & Download: ICSP AMS1117-3.3: 3.3V regulator device 16-bit I/O Port: of which 8bit for AD port 8-bit I/O Port: for 8-bit keypad module, motor control module, etc SPI Port: for Dataflash AT45DBXX, SD card, MP3, etc I2C Port: for I/O expansion chip PCF8574, EEPROM AT24CXX, etc 1-WIRE Port: for DS18B20, DS2401, etc UART Port: for RS232, RS485, USB TO UART, etc PS/2 Port: for PS/2 device keyboard, mouse, etc 2.2inch color LCD Port: SPI Character LCD Port: such as LCD1602 ICSP Port 5V DC Port Package included: 1 x Open16F877A Development Board 1 x USB Cable (mini) 1 x PL2303 USB UART Board (mini) 1 x 2.2inch 320 x 240 Touch LCD (A) 1 x AD Keypad 1 x FT245 USB FIFO Board (mini)(16I/O) 1 x AT45DBXX DataFlash Board (SPI) 1 x PCF8563 RTC Board (I2C) 1 x Micro SD Storage Board (SDIO/SPI)(not includes SD card) 1 x NRF24L01 RF Board (B)(SPI) 2Pcs 1 x DS18B20 (ONE WIRE) 1 x IR Remote Control 1 x LCD1602 (3.3V Blue)(Parallel) 1 x 8 SEG LED Board (16I/O) 1 x 8 Push Buttons (8I/O)

  KEY FEATURES 1080p recording resolution at 12 fps, 720p and lower resolutions at 25 fps Support for 4 HD-TVI or CVBS cameras Support for IE, Google Chrome, Opera, Safari Channel 0 - possibility to monitor all cameras with minimum demand for network bandwidth Parallel operation of HDMI, VGA and CVBS outputs HDMI/ VGA modes up to 1920 x 1080 pixels Searching recordings by alarm events VCA image analysis function Digital zooming during live monitoring and playback Synchronous playback from 4 channels Support for IPv4, IPv6, Monitoring the statuses of LAN, cameras, hard drives   RG59 CCTV CABLE  5 AMP POWER SUPPLY BNC CONNECTORS 12V DC    

  VIEW FROM YOUR SMART PHONES & COMPUTER    KEY FEATURES 1080p recording resolution at 12 fps, 720p and lower resolutions at 25 fps Support for 4 HD-TVI or CVBS cameras Support for IE, Google Chrome, Opera, Safari Channel 0 - possibility to monitor all cameras with minimum demand for network bandwidth Parallel operation of HDMI, VGA and CVBS outputs HDMI/ VGA modes up to 1920 x 1080 pixels Searching recordings by alarm events VCA image analysis function Digital zooming during live monitoring and playback Synchronous playback from 4 channels Support for IPv4, IPv6, Monitoring the statuses of LAN, cameras, hard drives   RG59 CCTV CABLE  5 AMP POWER SUPPLY BNC CONNECTORS 12V DC      

Buy RCT Infinisolar 10KVA/10000W 48V 14850W MPPT 3 Phase Hybrid On-Grid PV Inverter with Parallel Kit for R51,843.68

  Features: Pure Sine Wave Inverter Built-in MPPT Solar Charge Controller Selectable Input Voltages for Home Appliances and Selectable Charging Current Configurable AC / Solar input priority via LCD Setting Parallel Operation with up to 6 Units available on 5KVA (With a build in Parallel Kit) Overload and Short Circuit Protection Smart Battery Charger Design Cold Start Function  Specifications: Capacity - VA: 5000  W: 4000 Input Voltage: 230 VAC Surge Power: 10000 VA Acceptable Voltage Range: 170 - 280 VAC (Personal Computers), 90 - 280 VAC (Home Appliances) Frequency: 50 Hz / 60 Hz (Auto Sensing) Output - 50 Hz / 60 Hz (Auto Sensing): 230 VAC +- 5% Efficiency (Peak): 93% Transfer Time: 10-20 ms (Typical) Waveform (Battery Mode): Pure Sine Wave Battery Voltage: 48 VDC Floating Charge Voltage:54 VDC Shutdown Voltage: Configurable Overcharge Protection: 60 VDC Maximum PV Array Power: 3000 W MPPT Range at Operating Voltage: 60 - 115 VDC Maximum PV Array Open Circuit Voltage: 105 VDC Maximum Solar Charge Current: 60 A Maximum Charge Current: 110 A (AC + Solar) Maximum Efficiency: 98% Standby Power Consumption: 2W Physical Dimension D x W x H (mm): 120 x 295 x 468 Net Weight (kg): 9.8 Operating Humidity: 0 to 90% Relative Humidity (Non-Condensing) Operating Temperature: 0 C to 55 °C Storage Temperature: -15 C to 60 °C Expected Run times:          

SELECTED OPTION: TYPE: UNASSEMBLEKIT CLICK HERE for more options in this item. DIY Unassembled Kit User Manual: Assembled Kit User Manual: Specifications: Asssembled Item Size: 98x76x39mm Description: -The use of SCM ATMEAG328P DIP-28. With IC Block -The display unit using a 160x128 pixel color display, full-screen characters 8x20, 16-bit color depth, graphic display element symbols Rotary switch control, a key measurement, automatic shutdown -Use 9V laminated battery, can also use the power adapter(DC 6.8-12V), the whole current of about 30mA, after about 20nA shutdown current -Automatically detects NPN and PNP transistors, FET, diodes, dual diode, thyristor, SCR, automatic identification of the transistor pinout -Test NPN and PNP transistor common-emitter current amplification factor, the base - emitter threshold voltage, off the collector - emitter leakage current Pole through the transistor base - emitter threshold voltage and high current gain recognition Darlington transistor Detecting power transistor and FET protection diodes built -Test FET gate - source threshold voltage is turned on, the drain - source on-resistance, the gate - source capacitance A maximum of two measuring resistors, so three feet adjustable resistor can be measured, if adjustable resistor is transferred to the end, can only be a measured resistance value -Resistance measurement maximum resolution 0.01Ohm. Can be measured up to 50MOhm -Capacitor measuring range from 25pF-100mF, Resolution 1pF -Larger than 90nF capacitor while measuring its equivalent series resistance (ESR), the equivalent series resistance of the highest resolution of 0.01Ohm -Larger than 5000pF capacitor also showed the rate of decline after the charging voltage of the capacitor value can reflect the quality factor (Q value) -Measuring a maximum of two diodes show its positive and negative, on-state voltage -LEDs also display a graphic symbol diode, the conduction voltage is much higher than ordinary diode -Reverse breakdown voltage is lower than 4.5V Zener diode can detect it, appears as double diode symbol. Its positive and negative voltage to turn around 700mV diode symbol prevail, a second diode symbol corresponding to the voltage is turned on regulation. So do not be an ordinary diode and a Zener diode were measured simultaneously -Test a single diode, while its test reverse junction between the PN junction capacitance between the PN junction capacitance of the transistor to be tested, then only at the same time into the transistor base and the emitter, base and collector or Of less than 25pF capacitor to be tested, the test need to prepare a 30pF capacitor, 30pF capacitor to test, test and then measured again after the capacitor connected in parallel, by subtracting the measured value 30pF capacitors with the results obtained -For the following 2100Ohm resistor while measuring its inductance measuring range from 0.01mH - 20H -About two seconds during the test, large capacitors and inductors will take longer -Additional features include a frequency measurement, voltage measurement, square wave generator, PWM generator, color selection, commissioning calibration, continuous testing, and other functions -Frequency range from 1Hz to 1MHz or higher, measured at frequencies below 25kHz, can display period resolution to 0.001mHz -DC voltage measurement up to 50V -All the way to the square wave signal output, multi-range frequencies to choose from, the maximum output frequency of 2MHz -Output one fixed frequency, variable duty cycle pulse signal (PWM), the duty cycle is adjustable from 1% -99% -Separate capacitive function test, the test mode for the continuous measurement of 2uF-50mF capacitors can be measured directly in their circuit (circuit where the measured capacitance required power, after the measured capacitance required to be fully discharged) -Thyristors and thyristor can only recognize its pinout, and also need to test the thyristor or SCR trigger current is less than the current test instrument can provide, the tester can only provide a maximum trigger current 6mA Features: 1. Switch off 2. Transistor test 3. Frequency test 4. f-Generator 5. 10-bit PWM 6. C+ESR@TP1:3 7. continuous measurement resistance 8. 1-||-3 continuous measurement capacitance 9. Rotary encoder 10. SelfTest 11. Voltage test 12. FrontColor 13. BackColor adjust 14. Show date Package included: 1 x GM328 Transistor Tester with Case Kit (Assembled Kit or DIY Unassembled Kit For your choice.)

HYBRID B1600 PROFESSIONAL POWER AMP 800W RMS PER CHANNEL @4ohm STEREO,PARALLEL & BRIDGE MODE BALANCED LINE INPUTS CLIP LIMITER CIRCUIT INRUSH CURRENT PROTECTION DC PROTECTION SOFT START THERMAL PROTECTION WE STOCK A MASSIVE RANGE OF MUSICAL INSTRUMENT & AUDIO,TV,PROJECTOR & PA EQUIPMENT FOR LIVE,CHURCH,CONCERT,DJ, & OUTDOOR APPLICATIONS.OUR PRODUCTS INCLUDE PIANO,KEYBOARD,SUCH AS YAMAHA,GUITAR,DRUMS,MARCHING DRUMS,TRUMPET,TROMBONE,TUBA,SAXOPHONE,DJ,STUDIO EQUIPMENT,SOUNDCARDS THAT CAN BE USED ON LAPTOPS OR DESKTOP PC,WE ALSO STOCK AN AUDIO INTERFACE TO BE USED IN CONJUNCTION WITH A TABLET,IPAD,IPHONE,LAPTOP,MACBOOK,MACBOOK PRO,SAMSUNG AND OTHER ANDROID DEVICES AND CELLPHONES. WWW.SBRPROSOUND.CO.ZA ELECTRO VOICE 15" ACTIVE SPEAKER R9795. QTX QR15PA PORTABLE PA SYSTEM R5295. PEAVEY PORTABLE PROFESSIONAL PA SYSTEM R8795. ALESIS NITRO ELECTRONIC DRUM KIT R5995. ALESIS FORGE ELECTRONIC DRUM KIT R8795. ALESIS COMMAND ELECTRONIC DRUM KIT R11995. ALESIS CRIMSON MESH ELECTRONIC DRUM KIT R14995. WWW.SBRPROSOUND.CO.ZA

Low-cost high-performance mixer. The Soundcraft EPM8 is a 8x2 frame size mixer that places emphasizes on quality, audio performance, and an easy to understand, uncluttered control surface. Surface mount technology is used throughout this 8-channel mixer, using close-tolerance components for high accuracy and repeatable settings for EQ and gain controls. The highly transparent GB30 mic preamps--designed by Graham Blyth and used on the larger LX7ii and GB Series consoles--feature high-resolution adjustment over a wide gain range of 55dB, and provide a stunning +22dB headroom through the console. The Soundcraft EPM8's true professional 48-volt phantom power caters to condenser microphones of all types. Unique signal monitoring watches for overload in several channel strip locations and illuminates the LED more brightly as the signal approaches peak. 60mm high-quality faders are used. The monitor and headphone outputs work in parallel so that performers can listen on phones while an engineer listens to studio monitors. EPM8 Rackmount Kit Features 8x2 frame size 2 configurable auxiliary buses XLR-type and 1/4" metal jack connector sockets RCA phono stereo playback inputs and record outputs 3-band EQ with a swept mid on mono inputs 2-band EQ on stereo inputs TRS insert sockets and inserts on all mono inputs and mix output 10-segment LED output metering Intuitive and comprehensive solo system Headphone output Easily rack mountable