Original 5pcs ic

5pcs L293D L293 L293B DIP / SOP Push-Pull Four Channel Motor Driver IC Feature: Quantity: 5pcs Part number: L293D Manufacturer: ST Pin no: 16 pins Package included: 5 x L293D driver IC

5Pcs Jog Type Touch Sensor Module For Arduino Description: This is jog type capacitive touch switch sensor module based on a touch detection IC TTP223B. Normally, the output is low level(at mode of low power consumption). When the finger touch the corresponding location, output will be high(at quick speed mode). When the module do not be touched for 12 seconds, the mode would switch to low-power mode. It can be installed in the module, such as plastic, glass, non-metallic material surface. But not cover thin sheets(metal) on the surface of the module. Just touch the correct position, it can be hidden in walls, desktops and other parts to be buttons. Allows you to remove the troubles of conventional push-type buttons. Feature: Low power consumption Can replace the traditional key With four M2 screw holes, easy for operation Specification: Operating voltage: DC 2.0V ~ 5.5V VOH: VCC 0.8V VOL: VCC 0.3V Sink current: 8mA @ VCC = 3V, VOL = 0.6V Source current: -4mA @ VCC = 3V, VOH = 2.4V Response time: 220ms (at mode of low power consumption) and 60ms (at quick speed mode) Size: 24 x 24 x 7.2mm Package included: 5 x Capacitive jpg type touch sensor module

5Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module   Description:    Youve always wanted to output analog voltages from a microcontroller, the MCP4725 is the DAC that will let you do it! The CJMCU-MCP4725 is an I2C controlled Digital-to-Analog converter (DAC). A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller. Digital to analog converters are great for sound generation, musical instruments, and many other creative projects!   This version of the CJMCU-MCP4725 Breakout fixes a few issues with the board including the IC footprint, the I2C pinout, changes the overall board dimensions to better fit your projects, and a few more minor tweaks. This board breaks out each pin you will need to access and use the MCP4725 including GND and Signal OUT pins for connecting to an oscilloscope or any other device you need to hook up to the board. Also on board are SCL, SDA, VCC, and another GND for your basic I2C pinout. Additionally, if you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this.   Feature:   12-bit resolution I2C Interface (Standard, Fast, and High-Speed supported) Small package 2.7V to 5.5V supply Internal EEPROM to store settings   Package included:   5 x CJMCU-MCP4725 I2C DAC Breakout Development Board Module

Original Hiland 0-30V 2mA - 3A Adjustable DC Regulated Power Supply DIY Kit Short Circuit Current Limiting Protection English manual: Description:   This circuit voltage can be from 0 v, output current can be ma from 2 to 3 a continuously adjustable, set the output current, if the experiment circuit exceeds the current (including short circuit), the circuit protection immediately, not cause danger such as burning device, it is electronic manufacture's right-hand man. It is never afraid of the fireworks! Like making all kinds of audio circuit friend, often due to the different working voltage and circuit have a headache, this circuit can also two series into a dual power supply, can meet the needs of all sorts of use. Feature: Input voltage: 24V AC Input current: 3A maximum Output voltage: 0 to 30V continuous adjustable Output current: 2mA - 3A continuously adjustable output voltage ripple: minimum 0.01% All straight inserted element, make easy, only an adjustable components (used to adjust the voltage of 0 v) LED indicator for output over current, when the current exceeds the set data circuit protection, LED lighting, over load and short circuit protection Minimum current (2mA) under the measurable leds and zener diode Notice: Power production belongs to the high voltage large current circuit, please be sure to carefully, otherwise may cause harm to the personal safety Package included: 5 x Adjustable DC Regulated Power Supply DIY Kit

Buy 5Pcs Original ATTINY85-20PU ATTINY85 20PU ATTINY85- 20 ATTINY85 DIP Microcontroller IC Chip for R470.00

Buy 5Pcs Original ATTINY85-20PU ATTINY85 20PU ATTINY85- 20 ATTINY85 DIP Microcontroller IC Chip for R506.00

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Feature: Aluminum heat sinks for electronics, computers, electrical facilities, play a cooling effect Specification: Materials: Aluminum Size: 20*20*15mm (L*W*H) Color: Silver Qty: 5pcs Package included: 5 x CPU IC Chip Aluminum Heat Sink 5Pcs 20x20x15mm DIY IC Chip Heat Sink Extruded Cooler Aluminum Heat Sink 5Pcs 20x20x15mm DIY IC Chip Heat Sink Extruded Cooler Aluminum Heat Sink 5Pcs 20x20x15mm DIY IC Chip Heat Sink Extruded Cooler Aluminum Heat Sink

Buy 5pcs CV520 RFID RF IC Card Sensor Module Writer Reader IC Card Wireless for R359.00

Buy 5Pcs RFID IC Keyfobs 13.56 MHz Keychains NFC Key Card ISO14443A MF Classi For Smart Access Control S for R72.00

Buy 5pcs Miniature Digital Recording Voice IC Chip Module Movement Recorder for R215.00

Buy 5pcs MFRC-522 RC522 RFID RF IC Card Reader Sensor Module Solder 8P Socke for R259.00

Buy 5pcs Miniature Digital Recording Voice IC Chip Module Movement Recorder Recording Pen Music Card... for R209.00

Buy 5pcs MFRC-522 RC522 RFID RF IC Card Reader Sensor Module Solder 8P Socket for R307.00

Description: The 33886 is a monolithic H-Bridge ideal for fractional horsepower DC-motor and bi-directional thrust solenoid control. The IC incorporates internal control logic, charge pump, gate drive, and low RDS(ON) MOSFET output circuitry. The 33886 is able to control continuous inductive DC load currents up to 5.0 A. Output loads can be pulse width modulated (PWM-ed) at frequencies up to 10 kHz. A Fault Status output reports undervoltage, short circuit, and overtemperature conditions. Two independent inputs control the two half-bridge totem-pole outputs. Two disable inputs force the H-Bridge outputs to tri-state (exhibit high impedance). The 33886 is parametrically specified over a temperature range of -40°C ≤ TA ≤ 125°C, 5.0 V ≤ V+ ≤ 28 V. The IC can also be operated up to 40 V with derating of the specifications. The IC is available in a surface mount power package with exposed pad for heatsinking. Package included: 5 x CJMCU-3386 MC33186DH1 Automotive Computer Board Idle Speed Throttle Drive Board

Buy 5Pcs Aluminum Alloy Heatsink Cooling Pad for High Power LED IC Chip Cooler Radi for R608.07