Module kit white

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA 10pcs DIY Three Person Voter Module Kit DIY Electronic Production Kit 74HC00+74HC10 Description: Three-person voting device, designed with 74HC00 + 74HC10, three judges each control one of the three buttons S1, S2, S3, with the principle of minority subordinate to the majority of voting event, press agree, otherwise disagree. If the vote is passed, the LED will light up, otherwise it will not light up. Circuit board size: 5.5 x 2.7CM Supply voltage: DC3-6V Package Included: 10 x DIY Three Person Voter Module Kit 10pcs DIY Three Person Voter Module Kit DIY Electronic Production Kit 74HC00+74HC10 10pcs DIY Three Person Voter Module Kit DIY Electronic Production Kit 74HC00+74HC10

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: Three-person voting device, designed with 74HC00 + 74HC10, three judges each control one of the three buttons S1, S2, S3, with the principle of minority subordinate to the majority of voting events, press agree, otherwise disagree. If the vote is passed, the LED will light up, otherwise it will not light up. Circuit board size: 5.5 x 2.7CM Supply voltage: DC3-6V Package Included: 1 x DIY Three Person Voter Module Kit DIY Three Person Voter Module Kit DIY Electronic Production Kit 74HC00+74HC10 DIY Three Person Voter Module Kit DIY Electronic Production Kit 74HC00+74HC10 DIY Three Person Voter Module Kit DIY Electronic Production Kit 74HC00+74HC10

10-in-1 UNO Module Kit Buzzer Terminal Block DS18B20 Digital Module For Arduino Note: This kit does not includes any instructions, please note about this before order. Package includes: 1 x Mega V4 expansion board (small) 1 x Arduino compatible 5V relay module 1 x Arduino compatible MQ2 smoke gas module 1 x Arduino compatible analog temperature module 1 x Arduino compatible DS18B20 digital module 1 x Arduino compatible LED lamp module 1 x Arduino compatible button module 1 x Arduino compatible buzzer module 1 x Arduinocompatible 2pin terminal block 1 x Sliding rheostat module  

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Features: Kit name: Clap switch kit Working voltage: 4.5-5.5V PCB size: 27 x 49mm Kit function: Clap hand once, LED lit, and then clap once again LED turn off, so the cycle. Features: high sensitivity, about 4 meters clap can control. Note: This is a DIY kit, you need to assemble it. Package includes: 1 x PCB board 1 x MIC microphone head 1 x KF301-2P terminal block 1 x 47UF25V electrolytic capacitor 1 x 0.1UF50V electrolytic capacitor 4 x 104 monolithic capacitor 5 x 9013 transistor 1 x Colorful LED 2 x 1N4148 diode 1 x 510ohm resistance 8 x 4.7K resistance 6 x 10K resistance 1 x 750K resistance Voice Control Clap Switch Module Kit High Sensitive LED Rhythm Bistable Switch DIY Kit Voice Control Clap Switch Module Kit High Sensitive LED Rhythm Bistable Switch DIY Kit Voice Control Clap Switch Module Kit High Sensitive LED Rhythm Bistable Switch DIY Kit

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Feature: DIY electronic production of spare parts of wheel of fortune. Not easy to fall off, less prone to self becomes bent, impedance, more stable and reliable. Electronic wheel of fortune by a 10 LED form a circle, After you click the button, each LED luminous turn in order, flow speed getting slower and slower, and finally stopped in a move not only the LED. If the LED lights up with the players last forecast of the same, it means "winning". Specifications: Color: As the picture show Size: 5.8x5.8x0.1cm/2.28"x2.28"x0.039" Material: Paper board Supply voltage: 3-5V Package Included: 1 x DIY Flash Kit (With Battery case) 1 x Instructions(Chinese) DIY Wheel Of Fortune Training Module Kit Electronic Lucky Rotary LED Flash Kit DIY Wheel Of Fortune Training Module Kit Electronic Lucky Rotary LED Flash Kit DIY Wheel Of Fortune Training Module Kit Electronic Lucky Rotary LED Flash Kit

5Pcs MAX7219 Dot Matrix Module MCU LED Control Module Kit For Arduino Specifications: A single module can drive an 8 x 8 common cathode lattice Operating voltage: 5V Size: 5 x 3.2 x 1.5 cm (L x W x H) LED color: Red With four screws hole, aperture 3mm With input and output interfaces, supports multiple modules cascade Wiring instructions: 1. The module left side as an input port and the output port on the right 2. To control a single module, just connect the input port to the CPU 3. When cascading multiple modules, the input port of the first module connect to the CPU, the output port connect to the input port of the second one, and so on. In the case of 51 MCU: VCC → 5V GND → GND DIN → P22 CS → P21 CLK → P20 Note: 1. VCC and GND is not reversed, it would burn the chip! 2. When the 51 microcontroller P0 port controlling, must be connected to the pull-up resistor, it is recommended that the resistance of 4.7K--10K 3. Please install lattice into the round hole first, and then insert the round hole to PCB board and weld. Face the side of lattice with words, from left to right pin order is 123456. PCB board 1st pin is square pad! 4. Electrolytic capacitors long-pin as positive, short-pin as negative; ceramic capacitor hsa no positive and negative points Package included: 5 x LED module 5 x Dupont line (5P-20cm)

3Pcs MAX7219 Dot Matrix Module MCU LED Control Module Kit For Arduino Specifications: A single module can drive an 8 x 8 common cathode lattice Operating voltage: 5V Size: 5 x 3.2 x 1.5 cm (L x W x H) LED color: Red With four screws hole, aperture 3mm With input and output interfaces, supports multiple modules cascade Wiring instructions: 1. The module left side as an input port and the output port on the right 2. To control a single module, just connect the input port to the CPU 3. When cascading multiple modules, the input port of the first module connect to the CPU, the output port connect to the input port of the second one, and so on. In the case of 51 MCU: VCC → 5V GND → GND DIN → P22 CS → P21 CLK → P20 Note: 1. VCC and GND is not reversed, it would burn the chip! 2. When the 51 microcontroller P0 port controlling, must be connected to the pull-up resistor, it is recommended that the resistance of 4.7K--10K 3. Please install lattice into the round hole first, and then insert the round hole to PCB board and weld. Face the side of lattice with words, from left to right pin order is 123456. PCB board 1st pin is square pad! 4. Electrolytic capacitors long-pin as positive, short-pin as negative; ceramic capacitor hsa no positive and negative points Package included: 3 x LED module 3 x Dupont line (5P-20cm)

Description: STX882 ASK Wireless Remote Control Transmitter Module: STX882 is a ASK transmitter module with small size, ultra high power, low harmonics. With high stability, it can be achieved at 50mW power when the voltage is 3.6V, it is the maximum transmitter power module under the the same voltage in the market. Data port of the module can be connected to the microcontroller directly, make wireless product development and production more convenient. SRX882 ASK ASK Wireless Remote Control Superheterodyne Receiver Module: SRX882 is a superheterodyne receiver with micro power and strong driving force, is supplementary STX882 / STX888 module. Data port of the module can be connected to the microcontroller directly, make wireless product development and production more convenient. Module Function Demonstration DEMO Board: Package included: 5 x 433MHz 100m transceiver module kit (5pcs ASK transmitter STX882 + 5pcs ASK receiver SRX882 + 10pcs copper spring antenna)

Buy M5Stack PLC-PROTO Module Kit Expansion Function Module with RS485/ACS712-5B for R715.43

Buy DIY 6 Six Bit Big Screen Clock Kit Digital Clock Module Kit for R300.00

DIY Audio Stereo Power Amplifier Board Module Kit Advanced Tpye Specification: PCB size: 8.3 x 4.6cm Resistance: 6 ring blister copper Voltage: 9-15v Panel Thickness: 1.6mm Note: This is a un-soldering kit, you need to have some knowledge of electronics and ability. Any problems caused by personal reasons, not covered under warranty. Package included: 1 x DIY power amplifier kit

DIY Audio Stereo Power Headphone Amplifier Board Module Kit Standard Type Specification: PCB size: 8.3 x 4.6cm Resistance: 6 ring blister copper Voltage: DC 9-15V Panel thickness: 1.6mm Note: This is a soldering kit, you need to have some knowledge of electronics and ability. We don't offer instructions, please note about this before you order it. Any problems caused by personal reasons, not covered under warranty. Package included: 1 x DIY power amplifier kit

Buy 10pcs DIY Three Person Voter Module Kit DIY Electronic Production Kit 74HC00+74HC10 for R325.00

Buy 5pcs DIY Electronic Clapping Voice Control Switch Module Kit Induction Training DIY Production Kit for R193.95

Buy DIY NE555 Ding Dong Bell Doorbell Module Kit DIY Music DIY Electronic Production Training Kit for R108.85