Micro vtx rx

TS5823S Micro VTX 5.8G 200mW 48CH Mini FPV Transmitter SMA RP-SMA for RC Drone

Scisky Micro 32bits F3 Brushed Flight Control Board Built-in Receiver with 25MW 40CH 600TVL VTX&OSD Camera Description: It is includes one Scisky F3 flight control board Built-in RX, one VTX 25MW, one analog camera. The weight for the whole set is 6.7g. Specification:  Micro 32bits F3 Brushed Flight Control Board Size: 20.0*33.5*6.0mm (not including the USB protruding part) Weight:2.5g Frequency for driving motor: 2000 (the frequency can be set up by user, max frequency can be 32K) Brushed ESC: continuous working current is 4.2A, max current is 6A (5S); 1) Scisky F3 brushed flight control board based on F3 EVO hardware, supports CleanFlight and BetaFlight firmware. 2)Integrated with DCDC voltage booster circuit(output 5.0V/500Ma), it can supply power for other device through IIC and UART port; 3) There are 3 kinds of hardware for its built-in compatible receiver: A---CYRF6936, B---CC2500, C---A7105. 4) There are 4 option protocols for the built-in compatible receiver: 1=>DSMX/2; 2 =>Futaba SFHSS; 3=> FrSky; 4=> FlySky AFHDS 25MW VTX&OSD Output power: 25MW Frequency: 40CH Integrated with OSD, plug and play. Analog camera   Type: Colour Signal: PAL Pixel Size: 6.0um*6.0um Camera resolution: 600TVL Pick Up device: 1/3” COMS Active Pixel Array: 652*582 Sensitivity: 10V/Lux-sec S/N Ratio: 45 dB Resolution: 520TV Lines Gain Control: Auto White Balance: Auto Power Supply: 3.6~6.0V DC Power Consumption: 100mA Dimensions: 17.2*16.5mm Weight:2.4g Operating Temperature: -10~60¿¿¿ Lens angel: 120 degree The cable length is 80mm   Features: 1) STM32F303CCT6 main controller; 2) MPU6500 sensor (SPI way) 3) 6 optional built-in receivers; 4) Onboard 5V/1000mA DCDC booster circuit; 5) 4 built-in brushed ESCs (each brushed ESC can support current up to 6A); 6) No need soldering for installing VTX-25MW module or VTX-25MW & OSD module (note: analog VTX is 40CH) 7) Every built-in receiver on the board outputs receiver signal in the same 8CH PPM format and order, the channel number depends on customer’s transmitter; 8) Customer can set up the working frequency of VTX according to his own request through transmitter; MX VTX 25MW module (video transmitter) can be plugged and installed on Scisky F3 brushed flight control board directly, no soldering is needed, and also you can plug and play MX VTX-25MW & OSD and the analog camera, please check the following picture for reference: Ports diagram (same on all of the Scisky F3 brushed FCs) M1~M4 ports are for connecting brushed motors, each of which is marked S1, S2, S3 and S4 on the board, “+” is for positive of the brushed motor. COM1 and COM2 are for MX VTX-25MW or MX VTX-25MW & OSD. Binding operation: Two ways for binding operation: the first way is to long press the button for 2 seconds and enters binding mode; the second way is timeout binding mode. The built-in receiver for entering binding mode in the first way: 3=> Futaba SFHSS compatible receiver; The built-in receiver for entering binding mode in the second way: 1=>DSMX/2; 2 =>DEVO (on testing); 4=> FrSky (on testing); 5=> FlySky AFHDS; 6=>Hubsan; Note: LED light A flashes quickly indicates entering binding mode, solid LED light A indicates signal is received and stable. Frequency checking and setting up on analog video transmitter (the operation way will be changed according to feedback from customers): 6 LED lights on the board indicates the working frequency of the video transmitter in binary calculation way, LED 1, LED 2, LED 3 represent 5 groups of frequency, LED A, LED B and LED C show 8 frequencies. Pull the throttle to lowest, press the button slightly, you can check the current wor

Eachine M80S M80 Micro FPV Racer Drone Spare Parts 5.8G 25MW 48CH VTX 600TVL CMOS 1/3 FPV Camera Description: Brand Name: Mirarobot Item Name: FPV VTX Camera Channels: 48CH Camera: 600TVL HD CMOS 1/3 inch Camera Video Output format: PAL / NTSC AV Wireless Transmitter: 5.8g 25mw 48ch Power dissipation: 200-215mA@5V Operating Voltage: 2.9V-5.5V Size: 14.5*12*9.22mm Weight: 4g Usage: for Mirarobot M80S M80 Micro FPV Racing Drone Package Included: 1 x Camera

Buy 5Pcs Lantian Micro 5.8G FPV TX/RX Omni Directional Brass Gain Welded Antenna Fo for R311.44

Buy Lantian Micro 5.8G FPV TX/RX Omni Directional Brass Gain Welded Antenna For DIY Racing Quadcopter for R200.00

Buy 20x20mm HGLRC F438-TX20 V2 Flytower Micro F4 Flight Controller & 33A BL_S ESC & 25/100/200/350mW VTX for R1,904.55

Buy (Receiver DSMX)Oversky F3 EVO Micro Brushed Flight Control Board Built-in FlySky Frsky DSM RX fo... for R879.00

JJRC JJPRO-T1 95mm Micro Brushed FPV Racing Quadcopter Based On Naze32+DSM2 Brushed Flight Controller User Manual, Please Download JJRC JJPRO-T1:95 mm Wheelbase Description: Brand name: JJRC JJPRO-T1  Wheelbase:95mm Battery: 3.7V 600mah 30C lithium battery Frame kit: (including aluminum post,screw,motor coil) Material: pure carbon fiber Bottom plate thickness: 1.5mm Upper plate thickness: 1mm Motor: MD8520 Coreless Motor: Long diameter (without motor shaft): 20mm Wide diameter: 8.5 mm Weight: 4.8 g Naze32 + DSM2 brushed flight controller (integrated board): Using 32-bit ARM microprocessor, working in 3.3V / 72MHZ With gyroscope, support manual mode, horizontal mode Firmware upgrades and tuning can be performed via Micro-USB There are Baseflight-Configurator and Cleanflight-Configuration Camera: FOV150 °, 170 ° diagonal viewing angle NTSC / PAL system can be a key switch Operating voltage: 3.6-5.5V CMOS 1/3 sensor. Video image performance Imaging parameters and wide angle for FPV rigorous debugging 5.8G 40CH AIO FPV CAMERA: Support video format: NTSC / PAL Output Impedance: 75 Ohm Output signal strength: 12-14dB Operating voltage: 3.6-5.5V Audio carrier: 6.5MHz Weight: 6.8 g Channel: 40ch (Frequency channels list, please refer to the product specification) Features: 1.Use immediately, do not assemble and debug 2.Open - source flight control can be adjusted according to the player 's personal preferences from the stable, semi - self - stability, convenient to different levels of players manually 3. According to the race standard RaceBand VTX CAM 40 channel transmitter, Cmos 1/3 800Tvl high-definition camera, NTSC / PAL system can be a key switch Package included: 1x Bracket(aluminum post,screw,motor coil) 1x Naze32+DSM2 brush control(Integration builds) 1x 5.8G Cmos 800Tvl 40CH 25MW FPV Camera 4x 8.5*20 motor 2x Propeller(6 pieces) 1x 3.7V 600Mah 30C lithium battery 1x USB direct charging head 1x Spanners 4x motor coil 1x Attaching plug 1x Color box packing(including specifications)    

Smallest  Mini  Dual GLONASS+GPS BN-180 Micro Double GPS Antenna Module UART TTL For CC3D F3 Description  Dimension:　18mm*18mm*6mm Weight: 4.9g Connector: 1.00mm spacing between the 4pins patch seat     Specification Electrical Characteristics Chipset: u-blox M8030-KT Receiving Format:　GPS,GLONASS,Galileo,BeiDou,QZSS and SBAS Frequency: GPS L1,GLONASS L1,BeiDou B1,SBAS L1,Galileo E1 Channels: 72 Searching Channel   Sensitivity Tracking: -167dBm Reacquisition: -160dBm Cold start: -148dBm Hot start: -156dBm   Accuracy Position Horizontal: 2.0 m CEP 2D RMS SBAS Enable (Typical Open Sky) Velocity: 0.1m/sec 95% (SA off) Timing: 1us synchronized to GPS time   Acquisition Time Cold Start: 26s Warm start: 25s Hot start: 1s   Data and Update Rate Support Rate: 4800bps to 921600bps,Default 9600bps Data Level: TTL or RS-232,Default TTL level Data Protocol: NMEA-0183 or UBX, Default NMEA-0183 Single GNSS: 1Hz-18Hz Concurrent GNSS: 1Hz-10Hz,Default 1Hz   Operational Limits Altitude: 50,000m Max Velocity: 515m/s Max Acceleration: Less than 4g   Power consumption VCC: DC Voltage 3.0V-5.5V,Typical: 5.0V Current: Capture 50mA/5.0V Operating temp:　-40 °C ~ +85°C Storage Temp: -40°C ~ +105°C    Indicator: TX LED:blue.The data output, TX LED flashing PPS LED:red.PPS LED not bright when GPS not fixed,flashing when fixed   Wiring: GND,TX output,RX input,VCC(3.0v-5.5v)   Package Included  1 x BN-180 GPS Module  2 x 15cm Cable

Buy 6 PCS Mini IPEX UFL. IPX to SMA Adapter Cable Antenna Extension Wire 20*20 for Micro VTX RX FPV S... for R279.00

Buy 3 PCS Mini IPEX UFL. IPX to RP-SMA Adapter Cable Antenna Extension Wire 20*20 for Micro VTX RX FPV S for R256.00

Buy 5PCS 45/135 Degree RP-SMA Male to SMA Female Antenna Adpater Connector For FPV Goggles VTX RX RC Dro for R314.41

Lawmate 50cm JST-PH 2.0mm Dupont 2.54mm 4P 1007#24 Silicone Cable Wire For FPV Package weight: 0.01 kg 50cm JST-PH 2.0mm to Dupont 2.54mm 4P Cable 1007#24 Silicone Wire For FPV AV VTX RX Transmitter Receiver RC Drone Airplane Description Length: 500mm Connector: JST-PH 2.0mm, Dupont 2.54mm Cable: 1007#24 Silicone Wire Package Included 1 x Cable Click here for more deals Lawmate 50cm JST-PH 2.0mm Dupont 2.54mm 4P 1007#24 Silicone Cable Wire For FPV Lawmate 50cm JST-PH 2.0mm Dupont 2.54mm 4P 1007#24 Silicone Cable Wire For FPV

Description: Away from our initial debut in the RC world, ZOHD has evolved into a mature, committed and responsible company. The Talon GT “Rebel” is the continuation of our new series called MKII, started with the highly acclaimed Dart XL “Extreme”. This series will feature an incredible set of high quality and ORIGINAL innovations, intended to give you the FPV aircraft for casual, mid and long range. With MKII, without cutting any corners, we went straight ahead with 100% biodegradable and environmentally friendly materials, metal gear servos, high quality power plants, protection for leading edges and skids, wing fences, vortex generators, dedicated bays for FPV gear, revolutionary multi-cam hard noses and much, much more. Talon GT is one of the most capable FPV planes in 2019, regardless wingspan and price. Can compete in range and speed with planes twice as big and twice the cost without blinking. Specifically design to fly with modern flight controllers, high power video transmitters and long range systems, Talon GT will give you the best FPV experience to date. Easy assembly, setup and maintenance… A true king of the skies! This is it! ZOHD Talon GT “Rebel” is ready to hit the skies around the world, and this is just the beginning… join us in this incredible adventure! Specifications: Brand Name: ZOHD Product Name: ZOHD Talon GT "Rebel" Material: Biodegradable BEPP Wingspan: 1000mm(39.37'') Length: 660mm(25.98'') Motor: 2216-1300KV ESC: 40A w/5V 3A BEC Servos: 9g Metal Gear Prop: 8x5 Wing Area: 14dm2 Wing Load: 92.8g/dm2(Max.) Recommended Battery: 4S 3300-4400mAh (not included) Flying speed: 30-100+km/h Features: - Thanks to its revolutionary and careful design, the plane performs and looks like no other in the market. - Small size airframe optimized for long range and portability, marrying the best from the old school with cutting-edge production technologies. - Carefully chosen airfoil gives the aircraft an incredible lift power and excellent handling in any circumstances. - Detachable wing and tail make it portable for an easy transport and deploy. - Keeping the tradition: Familiar V tail layout, easy to set up. - Fly Green: New ZOHD’s exclusive BEPP material isn’t only crash resistance, but even more important: 100% biodegradable. Future generations will thank you for that. - Light-weight composite hard nose for better protection of your expensive camera gear - Multi-camera nose: Compatible with 99% of the FPV and HD cameras in the market: Runcam HD, 2, 3S, Swift, Eagle, Split, GoPro H4-5-6-7, Session and much more! - Reversed wingtips, provide more lift force and ensure a super efficient wing surface - Carefully engineered wing fences. - Reinforced pushrods for better overall performance and safety. - Load it as much you want with a huge equipment bay! - Computer designed optimized air flow po d, that maximizes cooling, reducing the risk of crashes for overheated electronics. No more DIY foam cutting! - Impact resistant protection cover for main wings leading edge and belly will keep your plane away from wear and tear. - Built-in carbon fiber tube inside main wings for enhanced performance and rigidity. - Built-in carbon fiber square rod reinforcement all along the fuselage. - Exclusive VTX / RX bays with excellent air flow and away from interferences. - U-stand for comfort and convenience while setting up the plane. Ideal to level any kind of flight controller in the workbench. - Full spare parts supply available, worry free fun. Note: PNP version, transmitter,receiver,battery, and charger are not included. English Instruction, Click Here User Guide: Click Here Spare Parts, Click Here Package Included: 1x ZOHD Talon GT Rebel 1000mm Wingspan V-Tail BEPP FPV Aircraft PNP

9 PCS FuriousFPV JST-GH 1.25mm JST-SH 1.0mm Molex 2P 3P 4P Cable Wire For RX VT Package weight: 0.03 kg 9 PCS FuriousFPV JST-GH 1.25mm JST-SH 1.0mm Molex 2P 3P 4P Silicone Wires for RX VTX Camera GPS Bluetooth Buzzer Frsky RX Airspeed F-35 Lightning Wire Harness: Silicone wire (AWG 28) 9 Harness/set Package Included: (length and connector) Camera: 220mm - JST GH 4pins 1.25 to MOLEX 3pins 1.25 + MOLEX 2 pins 1.25 VTX: 400mm - JST GH 4pins 1.25 to JST GH 6pins 1.25 RX Frsky: 400mm - JST GH 4pins 1.25 to Molex 1.25 5pin TBS Micro Rx: 400mm - JST GH 4pins 1.25 to MOLEX 6pins 1.25 GPS: 200mm - JST GH 4pins 1.25 to MOLEX 4pins 1.25 Bluetooth: 100mm - JST GH 4pins 1.25 to JST SH 4pins 1.0 Air Speed: 200mm - JST GH 4pins 1.25 to MOLEX 4pins 1.25 Buzzer: 100mm - JST GH 2pins 1.25 to wire External wires for TBS Micro RX: 400mm - JST GH 4pins 1.25 to Molex Pins 1,25 Click here for more deals 9 PCS FuriousFPV JST-GH 1.25mm JST-SH 1.0mm Molex 2P 3P 4P Cable Wire For RX VT 9 PCS FuriousFPV JST-GH 1.25mm JST-SH 1.0mm Molex 2P 3P 4P Cable Wire For RX VT