Max signal

Description: 1.1 piece of 2-pin Electronic LED 12V Flasher Relay for most motorcycles; 2.Fix for Turn Signal Indicator, Hyper Flashing, Blinker LED Light 3.This Flasher Relay Controller will solve LED Light related turn signal indicator blinker problems  such as hyper fast flashing, not flashing, or light bulb burnt out 4.It can eliminate the usage of load resistor, directly replace any two-wire / 2-pin flasher relay and  operate with LED's or conventional bulbs at normal OEM flash rate*** 5.Easy Plug & Play installation; Waterproof design in solid-state efficient unit with no excess heat issue. Specification: Product Name: Flasher Relay Color: Black Material: Plastic Power: 150W Nominal Voltage: DC 12V Operating Voltage: 11V-15V Switch Current:Min. 0.05A - Max. 12A Switch Load: Min. 0.6W - Max. 150W Flashing Frequency: 90 times per min Operating Temperature: -40C to +80C Life Time: 500 working hours Fitment: LED turn signal, blinker, indicator, corner light Application: Fix Rapid Flash, Warning Canceller, Decoder Usage: Electric Electronic LED Flasher Relay Module Size: 44mm x 30mm x 13mm   Fitment: For Honda: RC-51, CBR900RR, CB919, CBR929RR, CBR954RR, CBR1000RR, CBR1100XX, 07+ CBR600RR, CBR600F2/F3/F4/F4i, VTX (1800C, 1800R, 1800S, 1300C, 1300S, 1300R), ST1300, GL1500, NT650, Shadow 750/1100 (VT750, VT1100), VFR800, etc.   For Kawasaki: 95-08 ZX-6R(R), 13 ZX-6R, ZX-10R, ZX-12R, ZX-14, Z-1000, 96-03 ZX-7R, 98-03 ZX-9R, ZXR1200(1100), ZZR1200, ZX1200, ZR-7, ZX-636, W650 (EJ650), 07-12 Versys, 09-13 650R, Z750S, 96-07 250R, 11-13 Ninja 1000, 08-13 KLR650, 500R, 96-09 Vulcan 500, 95-05 Vulcan 800, 06-13 Vulcan 900, etc.   For KTM: 125, 250, 350, 380, 400, 450, 500, 525, 530, 540, 620, 625, 640, 690, 950, 990, etc.   For Suzuki: 96-11 DR-650, 97-00 GSX-R600, 96-99 GSX-R750, 93-98 GSX-R1100, 97-01 TL1000S, 97-03 VZ800 (Marauder), 98-09 VS800GL (Intruder), 96-11 DR650 (Dual-Sport), LS650P (Savage), etc.   For Yamaha: YZF-R1, YZF-R6, YZF-600R, FZ-1, FZ-6, 09+ V-Max, FJR1300, MT-01, Super Tenere, TW200, Trailway, WR250R, XT250, FZ09, etc   Note: 1. The LED flasher does not plug & play replace all flasher relay. 2.For motorcycles with non-standard two wires flasher relay, it can still be used by removing the connector and hard wiring it. Even three wires 3-pin flasher relay can be replaced if one of the wires is a ground wire. 3.We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need. 4.Please allow 0.5-1 inch difference due to manual measurement.(1inch=2.54cm) 5.Instruction is not included,professional installation is highly recommended. 6.Please compare the flasher relay with your original one before purchasing.   Package Included: 1 X Flasher Relay

Description: 1.1 piece of 2-pin Electronic LED 12V Flasher Relay for most motorcycles; 2.Fix for Turn Signal Indicator, Hyper Flashing, Blinker LED Light 3.This Flasher Relay Controller will solve LED Light related turn signal indicator blinker problems such as hyper fast flashing, not flashing, or light bulb burnt out 4.It can eliminate the usage of load resistor, directly replace any two-wire / 2-pin flasher relay and operate with LED's or conventional bulbs at normal OEM flash rate*** 5.Easy Plug & Play installation; Waterproof design in solid-state efficient unit with no excess heat issue. Specification: Product Name: Flasher Relay Color: Black Material: Plastic Power: 150W Nominal Voltage: DC 12V Operating Voltage: 11V-15V Switch Current:Min. 0.05A - Max. 12A Switch Load: Min. 0.6W - Max. 150W Flashing Frequency: 90 times per min Operating Temperature: -40°C to +80°C Life Time: 500 working hours Fitment: LED turn signal, blinker, indicator, corner light Application: Fix Rapid Flash, Warning Canceller, Decoder Usage: Electric Electronic LED Flasher Relay Module Size: 44mm x 30mm x 13mm Fitment: For Honda: RC-51, CBR900RR, CB919, CBR929RR, CBR954RR, CBR1000RR, CBR1100XX, 07+ CBR600RR, CBR600F2/F3/F4/F4i, VTX (1800C, 1800R, 1800S, 1300C, 1300S, 1300R), ST1300, GL1500, NT650, Shadow 750/1100 (VT750, VT1100), VFR800, etc. For Kawasaki: 95-08 ZX-6R(R), 13 ZX-6R, ZX-10R, ZX-12R, ZX-14, Z-1000, 96-03 ZX-7R, 98-03 ZX-9R, ZXR1200(1100), ZZR1200, ZX1200, ZR-7, ZX-636, W650 (EJ650), 07-12 Versys, 09-13 650R, Z750S, 96-07 250R, 11-13 Ninja 1000, 08-13 KLR650, 500R, 96-09 Vulcan 500, 95-05 Vulcan 800, 06-13 Vulcan 900, etc. For KTM: 125, 250, 350, 380, 400, 450, 500, 525, 530, 540, 620, 625, 640, 690, 950, 990, etc. For Suzuki: 96-11 DR-650, 97-00 GSX-R600, 96-99 GSX-R750, 93-98 GSX-R1100, 97-01 TL1000S, 97-03 VZ800 (Marauder), 98-09 VS800GL (Intruder), 96-11 DR650 (Dual-Sport), LS650P (Savage), etc. For Yamaha: YZF-R1, YZF-R6, YZF-600R, FZ-1, FZ-6, 09+ V-Max, FJR1300, MT-01, Super Tenere, TW200, Trailway, WR250R, XT250, FZ09, etc Note: 1. The LED flasher does not plug & play replace all flasher relay. 2.For motorcycles with non-standard two wires flasher relay, it can still be used by removing the connector and hard wiring it. Even three wires 3-pin flasher relay can be replaced if one of the wires is a ground wire. 3.We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need. 4.Please allow 0.5-1 inch difference due to manual measurement.(1inch=2.54cm) 5.Instruction is not included,professional installation is highly recommended. 6.Please compare the flasher relay with your original one before purchasing. Package Included: 1 X Flasher Relay

Universal Car FM Radio Aerial Antenna Signal Amplifier Booster Male To Female Feature: Frequency:80-108MHz Impedance:75Ohm Nominal V.S.WR:2.0:1MAX Return Loss:-10dB MAX Radiation:Direct Gain(Peak):25-30dB Cable Loss:2.5dB/m Max@1575.42MHz Polarization:Right-handed Circular Current Consumption:35mA Voltage:12V With this adaptor,you will have better radio reception. Package Included: 1 X  Set of Antenna Signal Amplifier Booster

Tachometer Hour Meter Max RPM LCD Digital Display Motorcycle Bike Waterproof Package weight: 0.11 kg Description: Base Function: Digital Tachometer: Display range: 0-15,000RPM Display internal: MAX RPM Record: Display range: 0-15,000RPM RPM Input Pulse: Display range: 0.5, 1, 1.5, 2, 2.5, 3, 4, 5, 6 Total engine Hour Meter: Display Range: 0-99999H Display Unit: 1H Hour Meter A/B: Display Range: 000.0-999.9H Effective Temperature Range: -10￢ﾄﾃ - +60￢ﾄﾃ Meter Size: 62x34x16.4mm (LxWxH) Cable Length: approx. 195cm Voltage Display Range: 0-24V Wiring Installation Instruction: Red: connect to positive of power Black: Ground wire, connect to the switch key of motorbike Green: connect to the RPM signal Function Switch Instruction: The meter will turn on when you connect the red and black cable. The meter will turn off if you turn off your bike key which connect to power switch. MAX.Record Screen Set: Press the button one time to the Max.Record screen. In Max.Record screen, press the button one time to turn to the main screen. Press the button for 3 seconds to reset the Max.Record. The Button Function Instruction: Press the button one time to the Max.RPM record. Press the button one time to change from the Max.RPM record to the total engine hour meter. Press down the button for 3 seconds to reset the Max.RPM record. Press the button one time to change from the total engine hour meter to the hour meter A. (Note: When the hour meter will start to count time, the RPM symbol will flash every 0.5 second) Press the button one time to change from the hour meter A to the hour meter B. (Note: When the hour meter will start to count the time, the RPM symbol will flash every 0.5 second) Press down the button for 3 seconds to reset the hour meter A. Press the button one time to change from the hour meter B to the main screen. Press down the button for 3 seconds to reset the hour meter B. RPM Pulse Setting: In main screen, press down the button for 3 seconds to enter the RPM pulse setting. EX. You want to change the current setting pulse from 1 to 2. In main screen, press the button one time to enter the RPM pulse setting. EX. The original setting is 0.5(4C-1P). The piston type can be set is: 0.5, 1, 1.5, 2, 2.5, 3, 4, 5, 6 EX. The ignition angle setting is changed from 1 to 2 Press down the button for 3 seconds to back the main screen. Note: Most of the 4-stroke bikes with one single piston are igniting every 360 degree once, so the setting should be the same as the bikes with 2-stroke and one piston engine. 1.Instruction is not included,professional installation is highly recommended. 2. Please check the size measurement chart carefully before making payment. 3. Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm) 4. The color of the actual items may slightly different from the listing images due to different computer screen= Package Included: 1 X LCD Meter 1 X Sticker 1 X User Manual(English) Click here for more deals Tachometer Hour Meter Max RPM LCD Digital Display Motorcycle Bike Waterproof Tachometer Hour Meter Max RPM LCD Digital Display Motorcycle Bike Waterproof

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: Base Function: Digital Tachometer: Display range: 0-15,000RPM Display internal: MAX RPM Record: Display range: 0-15,000RPM RPM Input Pulse: Display range: 0.5, 1, 1.5, 2, 2.5, 3, 4, 5, 6 Total engine Hour Meter: Display Range: 0-99999H Display Unit: 1H Hour Meter A/B: Display Range: 000.0-999.9H Effective Temperature Range: -10￢ﾄﾃ - +60￢ﾄﾃ Meter Size: 62x34x16.4mm (LxWxH) Cable Length: approx. 195cm Voltage Display Range: 0-24V Wiring Installation Instruction: Red: connect to positive of power Black: Ground wire, connect to the switch key of motorbike Green: connect to the RPM signal Function Switch Instruction: The meter will turn on when you connect the red and black cable. The meter will turn off if you turn off your bike key which connect to power switch. MAX.Record Screen Set: Press the button one time to the Max.Record screen. In Max.Record screen, press the button one time to turn to the main screen. Press the button for 3 seconds to reset the Max.Record. The Button Function Instruction: Press the button one time to the Max.RPM record. Press the button one time to change from the Max.RPM record to the total engine hour meter. Press down the button for 3 seconds to reset the Max.RPM record. Press the button one time to change from the total engine hour meter to the hour meter A. (Note: When the hour meter will start to count time, the RPM symbol will flash every 0.5 second) Press the button one time to change from the hour meter A to the hour meter B. (Note: When the hour meter will start to count the time, the RPM symbol will flash every 0.5 second) Press down the button for 3 seconds to reset the hour meter A. Press the button one time to change from the hour meter B to the main screen. Press down the button for 3 seconds to reset the hour meter B. RPM Pulse Setting: In main screen, press down the button for 3 seconds to enter the RPM pulse setting. EX. You want to change the current setting pulse from 1 to 2. In main screen, press the button one time to enter the RPM pulse setting. EX. The original setting is 0.5(4C-1P). The piston type can be set is: 0.5, 1, 1.5, 2, 2.5, 3, 4, 5, 6 EX. The ignition angle setting is changed from 1 to 2 Press down the button for 3 seconds to back the main screen. Note: Most of the 4-stroke bikes with one single piston are igniting every 360 degree once, so the setting should be the same as the bikes with 2-stroke and one piston engine. 1.Instruction is not included,professional installation is highly recommended. 2. Please check the size measurement chart carefully before making payment. 3. Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm) 4. The color of the actual items may slightly different from the listing images due to different computer screen= Package Included: 1 X LCD Meter 1 X Sticker 1 X User Manual(English) Tachometer Hour Meter Max RPM LCD Digital Display Motorcycle Bike Waterproof Tachometer Hour Meter Max RPM LCD Digital Display Motorcycle Bike Waterproof Tachometer Hour Meter Max RPM LCD Digital Display Motorcycle Bike Waterproof

Description: Base Function: Digital Tachometer: Display range: 0-15,000RPM Display internal: MAX RPM Record: Display range: 0-15,000RPM RPM Input Pulse: Display range: 0.5, 1, 1.5, 2, 2.5, 3, 4, 5, 6 Total engine Hour Meter: Display Range: 0-99999H Display Unit: 1H Hour Meter A/B: Display Range: 000.0-999.9H Effective Temperature Range: -10¿¿¿ - +60¿¿¿ Meter Size: 62x34x16.4mm (LxWxH) Cable Length: approx. 195cm Voltage Display Range: 0-24V   Wiring Installation Instruction: Red: connect to positive of power Black: Ground wire, connect to the switch key of motorbike Green: connect to the RPM signal   Function Switch Instruction: The meter will turn on when you connect the red and black cable. The meter will turn off if you turn off your bike key which connect to power switch.   MAX.Record Screen Set: Press the button one time to the Max.Record screen. In Max.Record screen, press the button one time to turn to the main screen. Press the button for 3 seconds to reset the Max.Record.   The Button Function Instruction: Press the button one time to the Max.RPM record. Press the button one time to change from the Max.RPM record to the total engine hour meter. Press down the button for 3 seconds to reset the Max.RPM record. Press the button one time to change from the total engine hour meter to the hour meter A. (Note: When the hour meter will start to count time, the RPM symbol will flash every 0.5 second) Press the button one time to change from the hour meter A to the hour meter B. (Note: When the hour meter will start to count the time, the RPM symbol will flash every 0.5 second) Press down the button for 3 seconds to reset the hour meter A. Press the button one time to change from the hour meter B to the main screen. Press down the button for 3 seconds to reset the hour meter B.   RPM Pulse Setting: In main screen, press down the button for 3 seconds to enter the RPM pulse setting. EX. You want to change the current setting pulse from 1 to 2. In main screen, press the button one time to enter the RPM pulse setting. EX. The original setting is 0.5(4C-1P). The piston type can be set is: 0.5, 1, 1.5, 2, 2.5, 3, 4, 5, 6 EX. The ignition angle setting is changed from 1 to 2 Press down the button for 3 seconds to back the main screen.   Note: Most of the 4-stroke bikes with one single piston are igniting every 360 degree once, so the setting should be the same as the bikes with 2-stroke and one piston engine. 1.Instruction is not included,professional installation is highly recommended. 2. Please check the size measurement chart carefully before making payment. 3. Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm) 4. The color of the actual items may slightly different from the listing images due to different computer screen=   Package Included: 1 X LCD Meter 1 X Sticker 1 X User Manual(English)

Description: Base Function: Digital Tachometer: Display range: 0-15,000RPM Display internal: MAX RPM Record: Display range: 0-15,000RPM RPM Input Pulse: Display range: 0.5, 1, 1.5, 2, 2.5, 3, 4, 5, 6 Total engine Hour Meter: Display Range: 0-99999H Display Unit: 1H Hour Meter A/B: Display Range: 000.0-999.9H Effective Temperature Range: -10￢ﾄﾃ - +60￢ﾄﾃ Meter Size: 62x34x16.4mm (LxWxH) Cable Length: approx. 195cm Voltage Display Range: 0-24V Wiring Installation Instruction: Red: connect to positive of power Black: Ground wire, connect to the switch key of motorbike Green: connect to the RPM signal Function Switch Instruction: The meter will turn on when you connect the red and black cable. The meter will turn off if you turn off your bike key which connect to power switch. MAX.Record Screen Set: Press the button one time to the Max.Record screen. In Max.Record screen, press the button one time to turn to the main screen. Press the button for 3 seconds to reset the Max.Record. The Button Function Instruction: Press the button one time to the Max.RPM record. Press the button one time to change from the Max.RPM record to the total engine hour meter. Press down the button for 3 seconds to reset the Max.RPM record. Press the button one time to change from the total engine hour meter to the hour meter A. (Note: When the hour meter will start to count time, the RPM symbol will flash every 0.5 second) Press the button one time to change from the hour meter A to the hour meter B. (Note: When the hour meter will start to count the time, the RPM symbol will flash every 0.5 second) Press down the button for 3 seconds to reset the hour meter A. Press the button one time to change from the hour meter B to the main screen. Press down the button for 3 seconds to reset the hour meter B. RPM Pulse Setting: In main screen, press down the button for 3 seconds to enter the RPM pulse setting. EX. You want to change the current setting pulse from 1 to 2. In main screen, press the button one time to enter the RPM pulse setting. EX. The original setting is 0.5(4C-1P). The piston type can be set is: 0.5, 1, 1.5, 2, 2.5, 3, 4, 5, 6 EX. The ignition angle setting is changed from 1 to 2 Press down the button for 3 seconds to back the main screen. Note: Most of the 4-stroke bikes with one single piston are igniting every 360 degree once, so the setting should be the same as the bikes with 2-stroke and one piston engine. 1.Instruction is not included,professional installation is highly recommended. 2. Please check the size measurement chart carefully before making payment. 3. Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm) 4. The color of the actual items may slightly different from the listing images due to different computer screen= Package Included: 1 X LCD Meter 1 X Sticker 1 X User Manual(English)

Options: Description: Base Function: Digital Tachometer: Display range: 0-15,000RPM Display internal: MAX RPM Record: Display range: 0-15,000RPM RPM Input Pulse: Display range: 0.5, 1, 1.5, 2, 2.5, 3, 4, 5, 6 Total engine Hour Meter: Display Range: 0-99999H Display Unit: 1H Hour Meter A/B: Display Range: 000.0-999.9H Effective Temperature Range: -10￢ﾄﾃ - +60￢ﾄﾃ Meter Size: 62x34x16.4mm (LxWxH) Cable Length: approx. 195cm Voltage Display Range: 0-24V Wiring Installation Instruction: Red: connect to positive of power Black: Ground wire, connect to the switch key of motorbike Green: connect to the RPM signal Function Switch Instruction: The meter will turn on when you connect the red and black cable. The meter will turn off if you turn off your bike key which connect to power switch. MAX.Record Screen Set: Press the button one time to the Max.Record screen. In Max.Record screen, press the button one time to turn to the main screen. Press the button for 3 seconds to reset the Max.Record. The Button Function Instruction: Press the button one time to the Max.RPM record. Press the button one time to change from the Max.RPM record to the total engine hour meter. Press down the button for 3 seconds to reset the Max.RPM record. Press the button one time to change from the total engine hour meter to the hour meter A. (Note: When the hour meter will start to count time, the RPM symbol will flash every 0.5 second) Press the button one time to change from the hour meter A to the hour meter B. (Note: When the hour meter will start to count the time, the RPM symbol will flash every 0.5 second) Press down the button for 3 seconds to reset the hour meter A. Press the button one time to change from the hour meter B to the main screen. Press down the button for 3 seconds to reset the hour meter B. RPM Pulse Setting: In main screen, press down the button for 3 seconds to enter the RPM pulse setting. EX. You want to change the current setting pulse from 1 to 2. In main screen, press the button one time to enter the RPM pulse setting. EX. The original setting is 0.5(4C-1P). The piston type can be set is: 0.5, 1, 1.5, 2, 2.5, 3, 4, 5, 6 EX. The ignition angle setting is changed from 1 to 2 Press down the button for 3 seconds to back the main screen. Note: Most of the 4-stroke bikes with one single piston are igniting every 360 degree once, so the setting should be the same as the bikes with 2-stroke and one piston engine. 1.Instruction is not included,professional installation is highly recommended. 2. Please check the size measurement chart carefully before making payment. 3. Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm) 4. The color of the actual items may slightly different from the listing images due to different computer screen= Package Included: 1 X LCD Meter 1 X Sticker 1 X User Manual(English)

12V 16A 22mm Headlight Signal Light ON-OFF Switch With Compass For Motorcycle H Package weight: 0.11 kg 12V 16A 22mm Headlight Signal Light ON-OFF Switch With Compass For Motorcycle Handlebar Description: Come with compass. Waterproof and shock resistant. It is convenient and easy to use. Usage: Headlight switch, On off switch, Turn signal for lighting Specification: Color: Black, Silver Material: Aluminum Alloy Diameter: 22mm Cable Length: 58cm Voltage: 12V Max Current: 16A Wiring: Blue - positive Brown - negative Black - connect with the equipment, positive Fitment: Fits for most Honda, Yamaha, Suzuki, Kawasaki, Arctic Cat, Can-Am and Polaris 7/8 inch (22mm) diameter handlebars. Note: Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm) Package Included: 1 X 16A Motorcycle Handlebar Switch with compass Click here for more deals 12V 16A 22mm Headlight Signal Light ON-OFF Switch With Compass For Motorcycle H 12V 16A 22mm Headlight Signal Light ON-OFF Switch With Compass For Motorcycle H

12V Universal Motorcycle Turn Signal Indicator Flasher Blinker Relay Package weight: 0.06 kg 12V Universal Motorcycle Turn Signal Indicator Flasher Blinker Relay Features: Beautiful appearance Use standard plug foot Shockproof and waterproof Easy to install, plug and use Specification: MAX: 240W Quantity:1 pc Voltage: DC 12V Body Color: Black Lead length: about 29cm Flasher Relay Material: made of specie IC Flasher relay size: 5.6cm x 2.3cm x 2cm/L x W x H Function: When you replace LED turn signal indicator for your car, motorcycle or other vehicles, the indicator may strobe or not work. But you can avoid these problems with the product Fitment: Fit for motorcycle halogen, car, led lamp Package Included: 1 X Flasher Relay Click here for more deals 12V Universal Motorcycle Turn Signal Indicator Flasher Blinker Relay 12V Universal Motorcycle Turn Signal Indicator Flasher Blinker Relay

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Motorcycle Quad ATV Turn Signal Rear Brake Tail Light Chrome Skull Description: Material: ABS housing & PC lens Case Color: Chrome Lens Color: Red Tail Light Color: Red & Yellow Turn Light Color: Red & Warm White Wattage: total 20W 3 wires connection system Specification: Lens Size(LxWxH): 4"x 7"x 3.74" (10 cm x 18 cm x 9.5cm) Screw hole Diameter: 6mm Screw hole spacing: 3cm (1.18") Cable Length: 50cm (19.7") Adjustable mounting slot spacing: 5.5cm (2.16") min.& 15cm (5.9") max. Fitment: The Tail light complete set chopper, cruisers or classic motorcycle. Please see the Compatibility Table. Package Included: 1 X Chrome Skull Tail Light 2 X Chrome Skull Turn Signal Lights 2 X Chrome Skull Screws Motorcycle Quad ATV Turn Signal Rear Brake Tail Light Chrome Skull Motorcycle Quad ATV Turn Signal Rear Brake Tail Light Chrome Skull

Motorcycle Quad ATV Turn Signal Rear Brake Tail Light Chrome Skull Package weight: 0.52 kg Description: Material: ABS housing & PC lens Case Color: Chrome Lens Color: Red Tail Light Color: Red & Yellow Turn Light Color: Red & Warm White Wattage: total 20W 3 wires connection system Specification: Lens Size(LxWxH): 4"x 7"x 3.74" (10 cm x 18 cm x 9.5cm) Screw hole Diameter: 6mm Screw hole spacing: 3cm (1.18") Cable Length: 50cm (19.7") Adjustable mounting slot spacing: 5.5cm (2.16") min.& 15cm (5.9") max. Fitment: The Tail light complete set choppers, cruisers or classic motorcycle. Please see the Compatibility Table. Package Included: 1 X Chrome Skull Tail Light 2 X Chrome Skull Turn Signal Lights 2 X Chrome Skull Screws Click here for more deals Motorcycle Quad ATV Turn Signal Rear Brake Tail Light Chrome Skull Motorcycle Quad ATV Turn Signal Rear Brake Tail Light Chrome Skull

BUY IT NOW! FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: Material: ABS housing & PC lens Case Color: Chrome Lens Color: Red Tail Light Color: Red & Warm White Turn Light Color: Amber Voltage: DC 12V Wattage: total 20W Tail Light 3 wires length: 57.5 cm / 22.63" Turn Light 2 wires length: 30cm / 11.81" Specification: Lens Size(LxWxH): 4"x 7"x 3.74" (10 cm x 18 cm x 9.5cm) Screw hole Diameter: 6mm Screw hole spacing: 3cm (1.18") Cable Length: 50cm (19.7") Adjustable mounting slot spacing: 5.5cm (2.16") min.& 15cm (5.9") max. Fitment: The Tail light complete set choppers, cruisers or classic motorcycle. Please see the Compatibility Table. Package Included: 1 X Chrome Skull Tail Light 2 X Chrome Skull Turn Signal Lights 2 X Chrome Skull Screws Skull Motorcycle ATV Rear Taillight Turn Signal Brake Plate Skull Motorcycle ATV Rear Taillight Turn Signal Brake Plate Skull Motorcycle ATV Rear Taillight Turn Signal Brake Plate

12V 10A 7/8inch 22mm Motorcycle Handlebar Turn Signal ON-OFF Switch Package weight: 0.09 kg Description: 100% Brand New. Durable Easy to install. Fits for 12V 10A Motorcycle, Scooter, Mini Bike, ATV, Quad, Bicycle with 22mm 7/8″ Handlebar Wiring: Blue - positive Brown - negative Black - connect with the equipment, positive Usage: Headlight switch, On off switch, Turn signal for lighting It is convenient and easy to use. Specification: Color: Black Material: Aluminum Alloy Diameter: 22mm Cable Length: 58cm Voltage: 12V Max Current: 10A Package included: 1 x 10A Motorcycle Handlebar Switch Click here for more deals 12V 10A 7/8inch 22mm Motorcycle Handlebar Turn Signal ON-OFF Switch 12V 10A 7/8inch 22mm Motorcycle Handlebar Turn Signal ON-OFF Switch

12V Universal Motorcycle Turn Signal Indicator Flasher Blinker Relay Features: Beautiful appearance Use standard plug foot Shockproof and waterproof Easy to install, plug and use   Specification:  MAX: 240W Quantity:1 pc Voltage: DC 12V Body Color: Black Lead length: about 29cm Flasher Relay Material: made of specie IC Flasher relay size: 5.6cm x 2.3cm x 2cm/L x W x H Function: When you replace LED turn signal indicator for your car, motorcycle or other vehicles, the indicator may strobe or not work. But  you can avoid these problems with the product   Fitment: Fit for motorcycle halogen, car, led lamp   Package Included: 1 X Flasher Relay

12V 16A 22mm Headlight Signal Light ON-OFF Switch With Compass For Motorcycle Handlebar  Description: Come with compass. Waterproof and shock resistant. It is convenient and easy to use. Usage: Headlight switch , On off switch, Turn signal for lighting Specification: Color: Black, Silver Material: Aluminum Alloy Diameter: 22mm Cable Length: 58cm Voltage: 12V Max Current: 16A Wiring: Blue - positive Brown - negative Black - connect with the equipment, positive Fitment: Fits for most Honda, Yamaha, Suzuki, Kawasaki, Arctic Cat, Can-Am  and Polaris 7/8 inch (22mm) diameter handlebars. Note: Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm)   Package Included: 1 X 16A Motorcycle Handlebar Switch with compass

This Item is Dropshipped !!!!!!!!!!!!!! FREE SHIPPING !!!!!!!!!!!!!! Registered Airmail to your nearest R.S.A Post Ofice on all orders over R300.00 Features: The DOP-3X flasher relay is made of specie IC. Suitable for car/motorcycle halogen/LED lamp. When you use LED turn signal indicator for your car motorcycle or other autos the indicator may strobe or not work. Our product can avoid these problems. Shockproof and water-resistant. Use standard plug foot. Plug and play. Easy to install. Red lead is connected to positive pole of power supply. Green lead is connected to positive pole of turn signal indicator. Black lead is connected to negative pole of power supply. Specifications: Max power: 240W Voltage: DC 12V Product size: 5.6 * 2.6 * 2.2cm / 2.2 * 1.0 * 0.9in Product weight: Approx. 64g / 2.3oz Package size: 5.6 * 2.6 * 2.2cm / 2.2 * 1.0 * 0.9in Package weight: Approx.65g / 2.3oz Package List: 1 * Flasher relay   click here to view all items To keep our prices as competitive as possible, all our items are shipped directly from our international suppliers, therefore your package may be inspected at customs. Buyers are responsible for any duties / VAT on this item if any is charged which are collected by SAPO on behalf of SARS and is not included in the price.  Shipping takes 30 to 40 business days and could be delayed due to circumstances out of our control.

12V Universal Motorcycle Turn Signal Indicator Flasher Blinker Relay Features: Beautiful appearance Use standard plug foot Shockproof and waterproof Easy to install, plug and use Specification: MAX: 240W Quantity:1 pc Voltage: DC 12V Body Color: Black Lead length: about 29cm Flasher Relay Material: made of specie IC Flasher relay size: 5.6cm x 2.3cm x 2cm/L x W x H Function: When you replace LED turn signal indicator for your car, motorcycle or other vehicles, the indicator may strobe or not work. But you can avoid these problems with the product Fitment: Fit for motorcycle halogen, car, led lamp Package Included: 1 X Flasher Relay

  Description:   100% Brand New. Durable Easy to install. Fits for 12V 10A Motorcycle, Scooter, Mini Bike, ATV, Quad, Bicycle with 22mm 7/8″ Handlebar   Wiring: Blue - positive Brown - negative Black - connect with the equipment, positive Usage: Headlight switch , On off switch, Turn signal for lighting It is convenient and easy to use. Specification: Color: Black Material: Aluminum Alloy Diameter: 22mm Cable Length: 58cm Voltage: 12V Max Current: 10A   Package included:   1 x  10A Motorcycle Handlebar Switch

Description: Power save Waterproof, but not support soak Can take off/on by hand Also can use as the safe-light Patterns is clear and completely when speed up to 20kms/h Equipped with light sensor and movement sensor,flash only at night and action It will not work and save power when not riding Battery: Operated by 1x AAA(Included), could be max to 12h when it works Specification: Pattern is clear and completely when speed up to 20kms/hour Consist of 14 pcs colorful LEDs,each side have 7 LEDS light It can flash 30 different patterns,and the patterns will be changed every 4 seconds Note: The battery is not included Package Included: 1 X LED Wheel Tire Signal Spoke Light

Motorcycle ATV Skull Turn Signal Light Brake Tail License Plate Lamp For Harley Chopper Specification: Material: ABS housing & PC lens Surface Finish: Black Lens Size: L 4" x W 7" (10cm x 18cm) Screw hole Diameter: 6mm Screw hole spacing: 3cm (1.18") Adjustable mounting slot spacing: 5.5cm(2.16") min. - 15cm(5.9") max. Lens Color: Red Light Color: Red & Warm White Turn Light: Amber Voltage: DC 12V Wattage: total 20W Cable Length: about 58cm (22.8") Weight: 520g 3 wires connection system Placement on Vehicle: Rear Fitment: The Tail light complete set choppers, cruisers or classic motorcycle (Harley-Davidson,Honda,Kawasaki,Suzuki,Yamaha,ect.) Note: Instruction is not included. Package Included: 1 X Set of Integrated Tail Light and Signals light with Some Fixing Screws                

LED Motorcycle Bike Tire Wheel Signal Flashing Spoke Light Description: 100% Brand new and high quality Power save. Waterproof,but not support soak. Can take off/on by hand. Also can use as the safe-light Patterns is clear and completely when speed up to 20kms/h Equipped with light sensor and movement sensor,flash only at night and action It will not work and save power when not riding Battery: Operated by 1x AAA(Included), could be max to 12h when it works. Specification: Consist of 14 pcs colorful LEDs,each side have 7 LEDS light. It can flash 30 different patterns,and the patterns will be changed every 4 seconds. Package Included: 2pcs x Spoke Light

12V T25 3157 5630 SMD LED Car Turn Signal Light Bulb Yellow Feature: 1. Max lighting output 2. Ultra long lasting design 3. High Quality & Brightness LED Bulb 4. Low power consumption, save whole lot of energy 5. Twice brighter than regular LED bulb and 3-4 times brighter than stock bulb 6. Extreme Bright Xenon White 3157 Projector LED bulbs for backup reverse lights 7. Replace the stock 3157 bulb for backup reverse lights 8. 3x optical magnified projector in front which make the light output looks shape and clean Specification: Base type: T25 SMD quantity: 1 pcs Normal voltage: 12V DC SMD type: 3157 smd Colors available: Yellow Installation: Very easy to install, you just have to plug it in the socket. This LED bulb is polar sensitive, so in case the bulb won't light up, please flip it 180 degrees Note: Light through the projector, it will refracts some yellow lights on the edge, there is no problem with the bulbs itself. Package Included: 1 X T25 3157 SMD Turn Light Bulb

Description: Material: ABS housing & PC lens Case Color: Chrome Lens Color: Red Tail Light Color: Red & Yellow Turn Light Color: Red & Warm White Wattage: total 20W 3 wires connection system Specification: Lens Size(LxWxH): 4"x 7"x 3.74" (10 cm x 18 cm x 9.5cm) Screw hole Diameter: 6mm Screw hole spacing: 3cm (1.18") Cable Length: 50cm (19.7") Adjustable mounting slot spacing: 5.5cm (2.16") min.& 15cm (5.9") max. Fitment: The Tail light complete set choppers, cruisers or classic motorcycle. Please see the Compatibility Table. Package Included: 1 X Chrome Skull Tail Light 2 X Chrome Skull Turn Signal Lights 2 X Chrome Skull Screws

Description: Power save Waterproof, but not support soak Can take off/on by hand Also can use as the safe-light Patterns is clear and completely when speed up to 20kms/h Equipped with light sensor and movement sensor,flash only at night and action It will not work and save power when not riding Battery: Operated by 1x AAA(Included), could be max to 12h when it works Specification: Pattern is clear and completely when speed up to 20kms/hour Consist of 14 pcs colorful LEDs,each side have 7 LEDS light It can flash 30 different patterns,and the patterns will be changed every 4 seconds Note: The battery is not included Package Included: 1 X LED Wheel Tire Signal Spoke Light

Description: 100% Brand New. Durable Easy to install. Fits for 12V 10A Motorcycle, Scooter, Mini Bike, ATV, Quad, Bicycle with 22mm 7/8″ Handlebar Wiring: Blue - positive Brown - negative Black - connect with the equipment, positive Usage: Headlight switch, On off switch, Turn signal for lighting It is convenient and easy to use. Specification: Color: Black Material: Aluminum Alloy Diameter: 22mm Cable Length: 58cm Voltage: 12V Max Current: 10A Package included: 1 x 10A Motorcycle Handlebar Switch

Description: Durable Easy to install Waterproof and shock resistant It is convenient and easy to use Specification: Color: Black Material: Aluminum Alloy Diameter: 22mm Cable Length: 58cm Voltage: 12V Max Current: 16A Installation Instruction: Blue - positive Brown - negative Black - connect with the equipment positive Fitment: Fits for most Honda, Yamaha, Suzuki, Kawasaki, Arctic Cat, Can-Am and Polaris 7/8 inch (22mm) diameter handlebars   Package Included: 1 X 16A Motorcycle Handlebar Switch

Description: Durable and waterproof. Eliminate the need for tapping wires to install the load resistors Allow LED bulbs to blink at the normal rate Easy to use, directly replace the OEM two-pin flasher Can use a flat head screw driver to adjust the knob on the bottom to set its flashing speeds from 50c/m to 200c/m. Suitable for Cars,Boats, Motorcycles, etc. Specification: Material ABS&Metal Adjustable Degree 180 degrees Size(mm) Like the picture show Color Black PIN 2 Operating Voltage DC 12V Max Power 42W Switch Power 0.02A to 12A Flashing Frequency 50 times/min to 200 times/min Working Temperature -40°C to +80°C Package Included: 1pc X 2-Pin Flasher Relay

Description: Durable Easy to install Waterproof and shock resistant It is convenient and easy to use Specification: Color: Black Material: Aluminum Alloy Diameter: 22mm Cable Length: 58cm Voltage: 12V Max Current: 16A Installation Instruction: Blue - positive Brown - negative Black - connect with the equipment positive Fitment: Fits for most Honda, Yamaha, Suzuki, Kawasaki, Arctic Cat, Can-Am and Polaris 7/8 inch (22mm) diameter handlebars   Package Included: 1 X 16A Motorcycle Handlebar Switch