Geekcreit abs case diy

Overview: This ABS case is designed for the 4 channel Relay Jog Wifi Wireless Smart Home Switches. Size: 13.0 x 7.5 x 3.0cm Suitable for this three item: 1. USB 5V Or DC 7V-32V DIY 4 Channel WIFI Wireless Smart Home Switch 2. USB 5V Or DC 5V DIY 4 Channel WIFI Wireless Smart Home Switch 3. USB 5V Or AC 55V-220V Four Channel WIFI Wireless Smart Switch Package included: 1 x ABS Case(Not include the module)

Geekcreit™ DIY NodeMCU Lua 4WD Open Source ESP8266 ESP-12E WiFi Smart Car Kit Description: This WiFi RC smart car is designed and developed based on ESP-12E from ESP8266, which can be controlled by mobile, PC. Some useful download links: For NodeMcu Lua + WiFi Motor shield, please go to Product ID: 1021716 Motor DataSheet for Tank/Car Chassis: http://bbs.smartarduino.com/showthread.php?tid=2039 Chassis Installation http://bbs.smartarduino.com/forumdisplay.php?fid=21 Software manumal http://bbs.smartarduino.com/showthread.php?tid=2036 Android App http://bbs.smartarduino.com/showthread.php?tid=1978 iOS App http://bbs.smartarduino.com/showthread.php?tid=2037 FirmWare http://bbs.smartarduino.com/showthread.php?tid=2013 Motor shield http://bbs.smartarduino.com/showthread.php?tid=6 NodeMCU http://bbs.smartarduino.com/forumdisplay.php?fid=2 Features: Color: Red, Blue, Green, Black, Transparent (Optional) Motor power supply (VM): 4.5V ~ 36V, can be a separate power supply; Control power (VIN): 4.5V ~ 9V (10VMAX), can be powered separately; Module provides short-circuit sub (short the VM and VIN), you can easily use one power (which must be 4.5V ~ 9V) simultaneously drive and control the motor; Logic Operating current Iss: ≤60mA (Vi = L), ≤22mA (Vi = H); Working current driving portion Io: ≤1.2A; Maximum power dissipation: 4W (T = 90 ?? Control signal input level: High: 2.3V≤VIH≤VIN; Low: -0.3V≤VIL≤1.5V Working temperature: -25 ??~ + 125 ??/span> Drive Type: Dual high-power H-bridge driver Support wireless 802.11 b / g / n standards; Support STA / AP / STA + AP three operating modes; Built-in TCP / IP protocol stack to support multiple TCP Client connection (5 MAX); D0 ~ D8, SD1 ~ SD3: used as GPIO, PWM, IIC, etc., port driver capability 15mA; AD0: 1 Road ADC; Current: continuous transmission: ≈70mA (200mA MAX), Standby: Transfer rate: 110-460800bps; Support UART / GPIO data communication interface; Remote firmware upgrade (OTA); Smart Link supports intelligent networking capabilities. Car battery: 4 x AA batteries, batteries not included!! (Battery Case not included) Package included: 1 x car chassis 1 x ESP-12E motor shield 1 x NodeMCU development board

SELECTED OPTION: DESIGN: BLUEDIGITALTUBERED&GREENLEDWITHHOUSING CLICK HERE for more options in this item. Here is the case link for this clock  ID: 1053594 Product ID 1013812: Date, time, temperature by turns display and. Alarm clock function, the whole point timekeeping and music alarm function. Pioneered light control, There are eight options for the Chime ringtone and Alarm clock Alarm. A variety of colors LED optional. There are 8 kinds of LED: Blue digital tube+ Red & Blue LED with housing Blue digital tube+ Red & Green LED with housing Blue digital tube+ Red & Blue LED without housing Blue digital tube+ Red & Green LED without housing Red digital tube+ Red & Blue LED with housing Red digital tube+ Red & Green LED with housing Red digital tube+ Red & Blue LED without housing Red digital tube+ Red & Green LED without housing Green digital tube+ Red & Blue LED with housing        Green digital tube+ Red & Green LED with housing      Green digital tube+ Red & Blue LED without housing     Green digital tube+ Red & Green LED without housing Description:   Size: With       housing: 93 x 93 x 26 mm Without housing:   81 x 81 x 2 mm PCB thickness: 1.6 mm Materials: FR4 military level Operating voltage: DC5V Note: The color of the new case is blue as follwing picture, which is not affect the function.   Function:    Alarm clock: You can set the alarm for the length of time, and the music The whole point timekeeping: You can set the whole point of timekeeping, and the music   There are 7 kinds of music you can set:   A. "D""D""D""D" (Default alarm tone)  B. Broadcast timekeeping (The whole point timekeeping default ringtone) C. Jasmine (Chinese music) D. For Elise  E. Canon F. Give a little Time to Your Love (Richard Clayderman) G. BBK  (Chinese music)   Welding note:   1, P1 for the development of the interface, not welding. 2, component identification: Components with no positive or negative polarity: Resistance (R1~R15), Thermistor(RT1), Ceramic capacitors (C4, C5), Monolithic capacitor (C2, C3), Crystal oscillator (Y1), Keys (S1, S2). Distinguishing positive and negative elements:LED(D1~D60),Battery seat(BT1),Electrolytic capacitor(C1), Buzzer(LS1),These elements should be noted that the positive and negative poles of the circuit board are to be noted. Other multi pin element:IAP15W413AS (U1), DS1302(U2), S8550(Q1), Block USB (USB1), These  elements should be noted in the same direction as the circuit board. 3,Positive welding LED, digital tube, Thermistor, and other components of the welding in the back. 4,LED has two colors, the less number of color welding in a large number of corresponding position, and the rest of the  location of a number of more than one color. 5,U2, C4, C5, Y1, BT1 must be welded before the digital tube, pay attention to the points on the digital tube. 6,The working voltage of the kit is 5V, the battery on back is only for the power down save time. Schematic circuit:   Package included:   1 x Upgrade DIY EC1515A DS1302B Rotation LED Electronic Clock Kit 51 SCM Learning Board  

SELECTED OPTION: COLOR: RED CLICK HERE for more options in this item. Description: This tube clock is designed by different colors and dimensions of 60mm x 160mm.  it can show the big size digits and the led color block. That makes the clock looks more amazing. The backlight color can be auto change and refract the color by the acrylic case. By the way, it can turn on the sounds control function, you can wake it up by clap your hands and knock on the table. It also has 6 kinds of switch mode to changing the time, temperature, date and week. Manual is sharing ! Features: Large size two-color LED display; 12/24 hours mode; One Alarm; Touch key control(with sounds feedback); Sound wake up control(you can wake it up by clap your hands and knock on the table or touch both of the key); RGB led autochange backlight color; Hourly Chime backlight flash remind; 6 kinds of transition animation select can change the time, temperature, data and week. Using real time clock chip, data is not lost when power off with the backup battery(backup battery not include in the kit); 5V USB cable power supply; Dimensions of the clock: 60mmx160mmx12mm; Three pieces of the acrylic combination; Different color option(middle color): red, green, blue, white, yellow and ice blue; Function: Touch both keys at the same time to enter or exit the menu functions list. Short touch the Next key(Triangle shape) to select the different functions, the functions menu has TIME(Time setup), DATE(Date setup), ALARM(Alarm setup), SHOW(Set shows time mode), DISP(Set transition animation), Sound(Turn on voice control), FMT(Set 24/12H format), MOVE(Set led rectangular move mode), Brig(Brightness of tubes), B-LED(Backlight of the RGB led), and then touch the Confirm key(Round shape) to enter in parameters mode. Parameters: 1. Alarm setup: ON-turn on the time alarm; OFF-turn off the time alarm; 2. Shows time mode: AA:BB:CC-shows hour, minute and second; AA:BB-shows hour and minute(the separator points will flash per second); 3. Set display animation effect: 0-time only; 1-spin mode; 2-up and down mode; 3-one by one mode; 4-from left to right mode; 5-flash mode; 6-change directly; 4. Sounds control switch: ON-turn on the sounds control; OFF-turn off the sounds control; 5. Time format: 24H-24h time format; 12H-12h time format; 6. Set rectangular move: 0-all off; 1-drag out mode; 2-single mode; 3-double mode; 4-up and down mode; 5-all on; 7. Brightness of tubes: level:1-5; A-automatic brightness(7:00-19:00: maximum brightness; 19:00-7:00: level 2 brightness); 8. Backlight: 0-backlight off; 1-fast change; 2-slow change; 3-slowest change; Package included: 1 x DIY 6 Digit LED Large Screen Two-Color Digital Tube Desktop Clock Kit Touch Control(Without CR1220 Battery)

SELECTED OPTION: COLOR: WHITERED/BLUE CLICK HERE for more options in this item. Package included housing, without housing version: product ID Documents download: Optional Color: (With housing version) Red digital tube + Red/Green circle LEDs Blue digital tube + Red/Green circle LEDs White digital tube + Red/Green circle LEDs Green digital tube + Red/Green circle LEDs //////////////////////////////////////////////////////////////////// Red digital tube + Red/Blue circle LEDs Blue digital tube + Red/ Blue circle LEDs White digital tube + Red/ Blue circle LEDs Green digital tube + Red/ Blue circle LEDs EC1620 electronic clock introduction: Using MCU to read the clock data in DS3231, shown on the digital tube and LED. Digital tube and LED using LED special constant current drive chip TM1818 to achieve the best display effect. Using the voice control module to output sound, to achieve voice timekeeping and alarm function. Through the button can set the time, alarm clock and other functions. Compare with product ID::   This product          product ID 1053190 Chip DS3231 DS1302 PCB size 100x140mm 81x81x1.6mm Size with case 152x29x112mm 93x93x26mm Size of digital tube 1 inch 0.56 inch Size of LEDs 5mm 3mm Shape of LEDs Oval Round Sound Speaker Buzzer USB port Micro USB Mini USB Note: It is assumed that users have soldering skills and troubleshooting skills to assemble this kit. Buyers are advised that due to skills of user is involved in assembly it is not guaranteed every kit will end up being a working device. But we will make as much efforts as we can to approach that goal. When soldering the SMDs, the temperature can not too high, otherwise there is the risk of bad soldering. Please note that the direction of LED, LED long legs for the positive. The second digital tube's point is in the bottom, is different with the other three points. RT1 is a thermistor, RL1 is a photosensitive resistor. And the length of the pin should be enough to extend out of the shell. The speaker is connected to the O1 and O2 of the voice module and is glued to the lower right corner of the circuit board with a double-sided adhesive tape. Please be sure to finish soldering the back side of the components and then soldering the digital tube. Specification: Power: DC3V-DC5V (Adapter does not includes) Working current: Alarm current: Due to the relatively large working current, please use the high quality 5V1A power supply. Function Specification Voice timekeeping Support Chinese and English voice Light control function Intelligent dimming Temperature display Celsius and Fahrenheit selection 12/24 hour system Can be set to 12/24 hour display Circle LED mode setting 12 modes can be set Turn off the LED lights LED can be closed, leaving only digital tube display Timekeeping Can set the time period of the time (after the set can automatically report time) The voice timekeeping Support Chinese and English voice (need to press the button to report time, in the time display state, press the PLUS key to report the current time) Alarm setting 3 alarm clock can be set Alarm tone setting 12 ringtones are available Temperature calibration There may be ± 1 ° error Take turns the display function Year, month, day, hour, minute, temperature rotation display

Package included housing, without housing version: product ID 1132729 Documents download: Key-Function: http://files.banggood.com/2016/EC1620-Key-Function-V06.pdf Circuit diagram: http://files.banggood.com/2016/Circuit diagram.zip Manual: http://files.banggood.com/2016/EC1620_V06-manual.pdf Optional Color: (With housing version) Red digital tube + Red/Green circle LEDs Blue digital tube + Red/Green circle LEDs White digital tube + Red/Green circle LEDs Green digital tube + Red/Green circle LEDs //////////////////////////////////////////////////////////////////// Red digital tube + Red/Blue circle LEDs Blue digital tube + Red/ Blue circle LEDs White digital tube + Red/ Blue circle LEDs Green digital tube + Red/ Blue circle LEDs EC1620 electronic clock introduction: Using MCU to read the clock data in DS3231, shown on the digital tube and LED. Digital tube and LED using LED special constant current drive chip TM1818 to achieve the best display effect. Using the voice control module to output sound, to achieve voice timekeeping and alarm function. Through the button can set the time, alarm clock and other functions. Compare with product ID: 1053190:   This product          product ID 1053190 Chip DS3231 DS1302 PCB size 100x140mm 81x81x1.6mm Size with case 152x29x112mm 93x93x26mm Size of digital tube 1 inch 0.56 inch Size of LEDs 5mm 3mm Shape of LEDs Oval Round Sound Speaker Buzzer USB port Micro USB Mini USB Note: It is assumed that users have soldering skills and troubleshooting skills to assemble this kit. Buyers are advised that due to skills of user is involved in assembly it is not guaranteed every kit will end up being a working device. But we will make as much efforts as we can to approach that goal. When soldering the SMDs, the temperature can not too high, otherwise there is the risk of bad soldering. Please note that the direction of LED, LED long legs for the positive. The second digital tube's point is in the bottom, is different with the other three points. RT1 is a thermistor, RL1 is a photosensitive resistor. And the length of the pin should be enough to extend out of the shell. The speaker is connected to the O1 and O2 of the voice module and is glued to the lower right corner of the circuit board with a double-sided adhesive tape. Please be sure to finish soldering the back side of the components and then soldering the digital tube. Specification: Power: DC3V-DC5V (Adapter does not includes) Working current: Alarm current: Due to the relatively large working current, please use the high quality 5V1A power supply. Function Specification Voice timekeeping Support Chinese and English voice Light control function Intelligent dimming Temperature display Celsius and Fahrenheit selection 12/24 hour system Can be set to 12/24 hour display Circle LED mode setting 12 modes can be set Turn off the LED lights LED can be closed, leaving only digital tube display Timekeeping Can set the time period of the time (after the set can automatically report time) The voice timekeeping Support Chinese and English voice (need to press the button to report time, in the time display state, press the PLUS key to report the current time) Alarm setting 3 alarm clock can be set Alarm tone setting 12 ringtones are available Temperature calibration There may be 1 error Take turns the display function Year, month, day, hour, m

Specification: Supply voltage: DC 12V Static current: ≤35MA, attract current ≤65MA Output voltage: DC 12V Output power: 20A relay Measurement input: NTC (10K 0.5%) Waterproof Sensor Environmental requirements: -10 ~ 60?? Humidity 20% ~ 85% Dimensions: 48 x 40mm Cable length: About 52 cm Temperature control mode: ON / OFF Temperature range: -50 ~ +110°C Control accuracy: 0.1°C Hysteresis  accuracy: 0.1°C Refresh rate: 0.5S High temperature protection: 0 ~ 110°C Resolution:  When temperature is 0.1°C, the resolution is -9.9~99.9, other temperature segment is 1°C Package included: 1 x Digital temperature control switch with cable 1 x DIY Acrylic Case

Specifications: Panel Material: Acrylic Case Material: ABS Panel Thickness: 5mm Panel Button Hole Diameter: 6 x 30 mm, 2 x 24mm Joystick Hole: 1 x 30mm Panel Size: 30 x 20 cm Note: Acrylic surface protective film, please tear up before installation. Only Acrylic Panel and Case.The joystick, buttons and cables are not including. DIY parts, not assembled. Package Included: 1 x Arcade Joystick Acrylic Panel 1 x Arcade Joystick Case 1 Set Screws 1 Set Suckers

Buy (Light blue case)Geekcreit DIY 4 Digit LED Electronic Clock Kit Temperature Light Control Versi... for R259.00

Buy 20pcs 100x60x25mm DIY ABS Junction Case Plastic Electronic Project Box Enclosure for R525.00

Buy 20pcs 100x60x25mm DIY ABS Junction Case Plastic Electronic Project Box Enclosure for R448.00

5Pcs E1A1 ABS Battery Box Holder For 4 x 18650 Description: This item is Battery Box Holder DIY power supply Easy installation Battery type: 18650 Connection: soldering Application: You can use this case with your own battery to form power system supply. Case for rechargeable battery. Simple DIY recharge power supply Materil: ABS Color: Black Package included: 5 x E1A1 ABS Battery Box Holder

3Pcs E1A1 ABS Battery Box Holder For 4 x 18650 Description: This item is Battery Box Holder DIY power supply Easy installation Battery type: 18650 Connection: soldering Application: You can use this case with your own battery to form power system supply. Case for rechargeable battery. Simple DIY recharge power supply Materil: ABS Color: Black Package included: 3 x E1A1 ABS Battery Box Holder

Description: This is an easy make four-layer round led dimensional cylinder kit, it's all use DIP components. It has more than 20 kinds of special led gradient effect. Some kinds of the effect is star-flashing and lightning effect, it also has many spin move effect and led breathing effect. All of the effects is gradual change light up instead of directly light up, that makes the led animation looks more gentle. you can hang it up on the christmas tree to simulate the star flashing effect. Soldering grids of each led layer greehand would look terrible. It has a dual use round acrylic that can as a template to hold the led in place, that help you to solder each layer of the led grids more accurate and the same level. On the other hand it also use as a case to reinforce the bottom. This acrylic template is important for quality soldering, it makes the led cylinder easier and more precise. How to assemble it, click here ! Features: Using 32 Milky 5mm Highlighted Long Pin LED Display 23 Kind of LED Gradient Effect to Simulate the Star-Flashing or Lightning and other 3D LED circle Effect Each Animation has so many Random function Alll using DIP components to build,suitable for beginners Blue Round PCB Acrylic Template to help aligning the led grids to solder Switch Button to Switch the next effect Reinforce the Bottom by the Dual Use Round Acrylic Double Power Supply Option: Micro USB cable or Wire Connect Use Micro USB Cable to Connect a computer or phone charger to Supply it with the 5V Color: blue Dimensions: 43mm x 43mm x 105mm Function: 1. Use micro usb cable or power wire to supply 5V power; 2. Toggle the switch button to switch the next animation effect. Package included: 3 x DIY Blue Mini Star Flashing LED Cylinder Kit

10pcs 12V DIY 8 x AA Battery Holder Box Case With Leads Switch Feature:Material: ABS impact resistant materialHardware: Nickel-plated steelSpring: Nickel-plated steelRivet: NoneWire: 1007 # 26AWGColor: BlackPackage included:10 x DIY 12V 8 x AA Battery Holder Case Box With Leads Switch