Geekcreit 433mhz dc12v

Buy Geekcreit 315/433MHz DC12V 10A 1CH Single Channel Wireless Relay RF Switch for R238.50

Buy 433Mhz DC12V 1CH Wireless Remote Control Switch Relay Receiver Module + 2 RF Tr for R251.97

Buy Geekcreit 433MHz DC 12V 10A Relay 1CH Channel Wireless RF Remote Control for R119.00

Buy (Voltage 12V)Upgraded 433MHz DC12V Single Channel Small Size Access Control System Power Supply... for R239.00

Buy Geekcreit HC-12 433MHz SI4463 Wireless Serial Module Wireless Transceiver Transmission Serial for R210.00

Buy Geekcreit HC-12 433MHz SI4463 Wireless Serial Module Wireless Transceiver Transmission Serial Comm for R243.16

Description: You can APP remote your electrical equipment via this product; And please weld a 433MHz receiver board if you want to support 433MHz remote control; How to weld the 433MHz reverive board and other details please refer to following link; Package included: 1 x Wireless Switch

Description: You can APP remote your electrical equipment via this product; And please weld a 433MHz receiver board if you want to support 433MHz remote control; How to weld the 433MHz reverive board and other details please refer to following link; Click to know more information Package included: 1 x Wireless Switch

Description: 433MHz Wireless Door Magnetic Contact Sensor For Home Security This door magnetic contact applies widely to works, banks, stores, warehouses, offices and homestead, thanks to its kinds of protection abilities like anti-theft, anti-robbery, fire prevention, gas leakage protection and most importantly, emergency calls. Operating volt: DC12V Operating current: 8~15mA Quiescent current: 3uA Operating frequency: 433MHZ Transmiting distance: 100 meter in the open area.                                                                      Installation: less than 15mm between two part. Modulation Mode: ASK Operating Temp: -20~+60 Color: white Size: 71*36*15mm Packing included: 1 x 433MHz Wireless Door Magnetic Contact Details Pictures:

  Description:   433Mhz GSM Gateway Wireless Terminal Home Alarm System Home Burglar Alarm Dialer Fixed Cellular Terminal While the GSM Gateway is installed with a SIM card, it can fucntion as a mobile phone device. Normal analogue telephony devices (e. g. Cordless or Desktop Phone / FXO / PBX / VoIP equipment, etc.) could be connected to this GSM gateway. All the calls or communications will be accessed and transmitted via GSM network instead of traditional Copper Phone Wires. F eatures:   1. Multicolor backlight display (e. g.: blue, green) 2. Can dial the local calls, mobile calls, international calls and special free calls 3. Supports modem mode 4. No need to dial area code when calling local numbers 5. Automatically connects to IP network when dialing long distance(optional) 6. Automatic card-locking and netwok -locking enable 7. Caller ID display, time and date display, the power supply of battery can display at the same time on the LCD. 8. Cost rate setting enable S pecifications:  1. Networks support: GSM 900 / 1800 MHz 2. Frequency range: GSM 900MHz(Transmits: 890-915MHz, Receives: 935-960MHz) GSM 1800MHz (Transmits: 1710-1785MHz, Receives: 1805-1880MHz) 3.   Voltage: DC 9V /DC12V 4. Stand by hours: 48 Hours 5. Talk time: 2-6 Hours 6. Charging time: 6 hours 7. Power consumption: Static ≤ 25MA           emission ≤ 500MA 8. Peak power consumption: 0. 25W/0. 5W 9. Receive sensitivity:  -104db 10. Antenna increment: All directions:  5. 0db;  Certain/Selection:  12db Connect the terminal:   Package includes:   1 x GSM Gateway Main Unit 1 x Rubber Antenna 1 x 110 to 220Vac Power Supply 1 x English Manual   Details pictures:    

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Instructions: 1. Clear: Press and hold the learning button for about 3 seconds, the LED will go out, flash 3 times after a while, clear OK. 2, learning the code: press the learning button, the LED lights up, release the learning button, enter the learning mode, press any button of the remote control at this time, transmit the signal, when you see the LED on the receiving module flashes 3 times, that is Indicates that the learning pair code is OK. 3. The remote control after learning can be controlled. Specifications: Working Temperature: -25~75C Frequency band: +-0.2MHz ReceiveDistance: 20-100M (open space) Receive Sensitivity: -108dB Working Frequency: 433MHz(Others can be customized) Quiescent Current: Working Voltage: DC3.3~5V Working mode:Point move, self-locking, interlocking Pin: GND: groud or negative pole +V: DC3.3~5V input D0: Data output D1: Data output D2: Data output D3: Data output VT: Output Precautions: 1. Do not operate with power. Turn off the power and operate it. After the test is confirmed, the power is turned on. 2. When using wireless electronic products, care should be taken to avoid strong interference sources such as metal masks, large electronic devices, and electromagnetic fields to prevent the modules from working properly. 3. Do not use this electronic product abnormally. Abnormal use will reduce product performance and longevity. In severe cases, damage to the product will also pose a safety hazard. Package Included: 5 x RX480E-4 433MHz Wireless RF Receiver 5pcs Geekcreit RX480E-4 433MHz Wireless RF Receiver Learning Code Decoder Module 4 Channel Output 5pcs Geekcreit RX480E-4 433MHz Wireless RF Receiver Learning Code Decoder Module 4 Channel Output 5pcs Geekcreit RX480E-4 433MHz Wireless RF Receiver Learning Code Decoder Module 4 Channel Output

Features: Easy to install and easy to carry With a slidable cover on the remote control With a hook on the remote control Use Learning coding, stable and reliable The wireless signal can pass through walls, floors and doors You can turn on or turn off the receiver with transmitter (remote control) from any place within a reliable distance Operating Voltage: DC12V Maximum Load: 10A Operating Frequency: 433MHZ (in set) Receiver Sensitivity: -100dBm Encoding Type: learning code Board Size: Approx. 5.3x3.1cm/ 2.09x1.22" Output Working Way: 1. Jog: Pressing one button is working. Loosing your finger on the same button is stop. (need one channel switch and one buttons remote control) 2. Self-lock: Pressing one button for one time is working. Pressing the same button again is stop (need one channel switch and one buttons remote control) 3. Inter-lock: Pressing one button is working. Pressing another button is stop (need one channel switch and 2 buttons remote control) 4. Please notice that here is 1CH and 1 button wireless remote control. You can choose the self-lock or jog working/ output way, you better choose jog or self-lock, so pressing the button is open, and pressing again is close, or pressing is open, and loosing finger is close Learning and Remove Method: 1. Press the learning code. The indicator from on to off, loosen your finger, press any button of the remote control, the indicator flash 2 times and off. It mean you learn it successfully 2. It can learn more than 12 PCS 2262 or 1527 chip with the different code wireless remote control 3. Remove/ Clean: Press the learning button about 8 seconds, the indicator turn on to off, it means the information that you keep have been removed successfully Package Included: 3 x Learning Code Receiver 3 x Remote Control

Buy 100pcs DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch Receiver Module for R4,040.00

Buy 50pcs DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch Receiver Module for R2,205.00

Buy 20pcs DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch Receiver Module for R940.00