Function signal

DDS Function Signal Generator Sine Square Triangle Sawtooth Wave Low Frequency Specification: Operating Voltage: DC9V DDS frequency range: 1Hz-65534Hz High-speed frequency(HS) output up to 8MHz DDS signal amplitude of the offset amount can be adjusted separately by two potentiometers DDS signal: Sine wave, Square wave, Sawtooth, Reverse sawtooth, Triangle wave, the ECG wave and noise wave. 1602 LCD menu Intuitive keyboard Section into the value: 1, 10, 100, 1000, 10000Hz The power automatically restore the last used configuration Offset: 0.5Vpp-5Vpp Amplitude amount: 0.5Vpp-14Vpp Key Functions: UP output waveform select DOWN output waveform select LEFT output frequency- RIGHT output frequency+ STOP/RUN the output stop/start "UP" key waveforms order: ECG=electrocardiogram wave(in the OFF state, the "left" and "right" keys to set the output frequency. Middle button start, all of the following waveform set) Rev Sawtooth= reverse sawtooth Saw Tooth=sawtooth Triangle= triangle wave Square=Square wave Package included: 1 x DDS Function Signal Generator 1 x Power Adapter 1 x Q9 Signal Cable 1 x User's Manual

Description: ICL8038 is a kind of monolithic function signal generator with excellent performance. It can generate sine wave, triangle wave, square wave and square wave. Feature: Operating voltage: DC12V Working current: 9mA Frequency range: 50Hz--7.5KHz Duty cycle: 27%--63% (square wave) Signal type: sine wave, triangle wave, square wave Dimensions: 58*47*21mm Package included: 5 x DIY 8038 Function Signal Generator Kit

Buy 5Pcs DC12 DIY ICL8038 Function Signal Generator Kit Sine Triangle Square Wave Signal for R347.17

Buy 3Pcs DC12 DIY ICL8038 Function Signal Generator Kit Sine Triangle Square Wave Signal for R326.00

Specifications: Voltage supply: 9-12V DC Input Waveforms: Square, Sine & Triangle Impedance: 600 Ohm + 10% Frequency: 1Hz - 1MHz SINE wave: Amplitude: 0 - 3V at 9V DC input Distortion: Less than 1% (at 1kHz) Flatness: +0.05dB 1Hz - 100kHz SQUARE wave: Amplitude: 8V (no load) at 9V DC input Rise Time: Less than 50ns (at 1kHz) Fall Time: Less than 30ns (at 1kHz) Symmetry: Less than 5% (at 1kHz) TRIANGLE wave: Amplitude: 0 - 3V at 9V DC input Linearity: Less than 1% (up to 100kHz) 10mA Instruction: Click to open Package included: 3 x XR2206 Function Signal Generator DIY Kit  

Specifications: Voltage supply: 9-12V DC Input Waveforms: Square, Sine & Triangle Impedance: 600 Ohm + 10% Frequency: 1Hz - 1MHz SINE wave: Amplitude: 0 - 3V at 9V DC input Distortion: Less than 1% (at 1kHz) Flatness: +0.05dB 1Hz - 100kHz SQUARE wave: Amplitude: 8V (no load) at 9V DC input Rise Time: Less than 50ns (at 1kHz) Fall Time: Less than 30ns (at 1kHz) Symmetry: Less than 5% (at 1kHz) TRIANGLE wave: Amplitude: 0 - 3V at 9V DC input Linearity: Less than 1% (up to 100kHz) 10mA Package included: 1 x XR2206 Function Signal Generator DIY Kit

ICL8038 Function Signal Generator Kit Multi-channel Waveform Generated

DIY XR2206 Function Signal Generator Kit Sine Triangle Square Output 1HZ-1MHZ

Buy 10Pcs ICL8038 Function Signal Generator Kit Multi-channel Waveform Generated for R745.41

Buy 5Pcs ICL8038 Function Signal Generator Kit Multi-channel Waveform Generated for R352.13

Buy 8038 Function Signal Generator DIY Waveform Generator Kit Electronic DIY Production Parts for R190.91

Buy 5Pcs DC12 DIY ICL8038 Function Signal Generator Kit Sine Triangle Square Wave S for R415.57

Buy EQKIT DIY 8038 Function Signal Generator Kit for R175.00

Buy FY1005S 5MHz LCD Digital Display LCD1602 DDS Function Signal Generator Source Module Sine/Triangle/ for R830.00

Buy Geekcreit XR2206 Function Signal Generator DIY Kit Sine Triangle Square Output 1HZ-1MHZ for R178.00

Buy 3Pcs 8038 Function Signal Generator DIY Waveform Generator Kit Electronic DIY Production Parts for R287.00

Buy MDS-3200A DDS NC Dual Channel Function Signal Generator Frequency Meter TTL Wave (FREQUENCY: 25MHZ) for R1,613.00

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: This module is a multichannel current signal generator that generates 4 channels 4~20mA current signal. The module is simple to use and input data by keystroke operation, and the output signal is updated immediately. Features: Use 12864 LCD display Voltage: 15-24V Active output current 0~20mA. Display resolution 0.01mA and control accuracy 0.1mA Polarity protection of input voltage Can analog transmitter output Compatible for signal generator, valve regulator, and instrument calibration Specifications: Output current: 4~20mA Resolution: 0.01mA Control accuracy: 0.1mA Application: signal generator, valve regulator, and instrument calibration Size: 12*9*2cm / 4.72*3.54*0.19inch(length*width*height) Weight: 75g Interface(power interface) description: CN1 "+": represent the positive pole of the input power supply CN1 "-": represent the negative pole of the input power supply(GND) CN1 "OUT1": represent channel 1 transmit current output CN1 "OUT2": represent channel 2 transmit current output CN1 "OUT3": represent channel 3 transmit current output CN1 "OUT4": represent channel 4 transmit current output CN1 "G": represent common end GND Button description: Function button K1: the up arrow key is used to select the setting channel Function button K5: the down arrow key is used to select the setting channel Function button K2: reduce 0.01 slowly. Hold down 1S reduce 0.1 Function button K3: increase 0.01 slowly. Hold down 1S increase 0.1 Function button K6: actual value or percentage selection key Function button K8: clear key Using methods & steps: Output current OUT1 setting: press K1 or K5 Key to switch to OUT1 Setup interface. Press K2 or K3, output current value increases 0.01 MA step by step. Hold down K2 or K3, output current value increases 0.01MA step by step. Output current OUT2 setting: press K1 or K5 Key to switch to OUT2 Setup interface. Press K2 or K3, output current value increases 0.01 MA step by step. Hold down K2 or K3, output current value increases 0.01MA step by step. Output current OUT3 setting: press K1 or K5 Key to switch to OUT3 Setup interface. Press K2 or K3, output current value increases 0.01 MA step by step. Hold down K2 or K3, output current value increases 0.01MA step by step. Output current OUT4 setting: press K1 or K5 Key to switch to OUT4 Setup interface. Press K2 or K3, output current value increases 0.01 MA step by step. Hold down K2 or K3 output, current value increases 0.01MA step by step. Package included: 1 X Current signal generator module board 4 Channels 4-20mA Current Signal Generator Module Board With 12864 Digital LCD Display 4 Channels 4-20mA Current Signal Generator Module Board With 12864 Digital LCD Display 4 Channels 4-20mA Current Signal Generator Module Board With 12864 Digital LCD Display

VC77 Digital Multimeter 2 In 1 4-20MA Signal Output Multimeter Process Signal S Package weight: 0.62 kg Features: 1.Multimeter & Signal Source 2 in1 2. Loop detection function A. Simultaneously supply 24V loop and measure current. B. Built-in 250 ? HART loop resistor for easy access to HART communication devices without the need to carry load resistors separately. 3. Analog output function A. 4~20mA current setting by bit, manual step output function. B. SIMULATE function simulates the transmitter. C. Can be displayed in mA and percentage. D. The output accuracy is 0.2%, and the output is displayed as 5 bits. 4. Measurement function A. AC voltage, DC voltage, ohmic, DC current, on and off, diode. B. The measurement accuracy is 0.5%, and the current measurement is displayed as 5 bits, which is displayed as 4 bits. C. Measurement rate: 2.5 times / sec D. Can be displayed in mA and percentage. E. Data retention function. 5. Use panel calibration technology. Specifications: Display Screen: display in four digits(5 in current measurement and output) Refresh display:2.5 displays/second Operation temperature and moisture range:0~40 ºC, relative moisture≤85%(no condensation) Storage temperature and moisture range:-20 ºC~60 ºC,relative moisture≤90%(no condensation) Accuracy required temperature and moisture range:23±5ºC,relative moisture≤75%(no condensation) Temperature co-efficiency:0.1 × basic accuracy / ￢ﾄﾃ(temperature range 28￢ﾄﾃ) Continuity/open test:Beeper sounds for resistance readings below threshold, or to indicate a momentary open circuit Battery type:two AA 1.5V Alkaline (LR6) batteries(Not included) DC current output(SIMULATE): about 50 hours; DC current output (SOURCE)20mA(1000Ω load): about 2.5 hours. Battery life:when using alkaline battery: measures any parameter: about 100 hours; Low battery:displays battery symbol Automatic power-off:The default value is 5 mins if no operation which is adjustable. Preheating time:10min Measuring detailed accuracy indicator Measuring part range frequency accuracy remark DC voltage 50V 10mV 0.5%+4 • Measuring impedance 10 MΩ (standard value) • Common mode restrain: 50Hz or 60Hz > 100Db • String mode restrain:50Hz or 60Hz > 45dB • Overload protection: 600V (pea'k –pea'k value) AC voltage 500V 100mV 0.5%+20 (45Hz~100Hz) • frequency beeps: 45Hz~400Hz • Adaptive to range from 10% to 100% • AC conversion: mean value • Measuring impedence:10 MΩ(standard Click here for more deals VC77 Digital Multimeter 2 In 1 4-20MA Signal Output Multimeter Process Signal S VC77 Digital Multimeter 2 In 1 4-20MA Signal Output Multimeter Process Signal S

Description:   DDS function / arbitrary waveform generator uses direct digital synthesis technique (DDS), FPGA design, interior prefabricated 7 kinds of commonly used waveform while users can also edit the output 8-bit, 256 points user-defined arbitrary waveforms; its easy to use, the signal high stability, low distortion, with 1 watt power output, wideband frequency measurement and counter functions. The output signal amplitude and DC offset can be adjusted. Waveforms: sine, square, triangle, ramp, user-defined waveform (Arb), commonly used pulse, noise, electrocardiogram waveforms.   Parameters:   Signal output: o utput waveform Sine, square wave (variable duty cycle), triangle wave, sawtooth.A rbitrary waveforms, commonly used pulse, noise, ECG, AM, FM and other waveforms Output amplitude ≥ 0.5-8V p-p (no load) Output impedance 10 ohms ± 10% Power supply: DC 5V DC bias ± 3V Frequency range 0.01Hz~50kHz  Frequency resolution 0.01Hz (10mHz) Frequency accuracy ± 5 x 10-6 Frequency stability ±2 x 10-6 / 3hours Sine wave distortion ≤ 0.8% (Reference frequency 1kHz) Triangle wave linearity ≥ 98% (0.01Hz~10kHz) Square wave an increase of fall time ≤ 100ns Square wave duty cycle range 1%~99% Counter function:   Counting range 0-65535 Measurement frequency range 1Hz~20MHz Input amplitude 0.5V p-p~20V p-p   Others:   1. Size: 83*60*24mm  (length* width* height) 2. Display LCD 1602 LCD display in English 3. Storage and recall function M0-M9 (M0: default transferred) 4. Buzzer function can be programmed to turn on or off 5. Production process surface mount technology, LSI 6. Operating characteristics all key operations, continuous adjustment knob 7. Environmental conditions temperature‚0~40°c Humidity¸ Package included: 1 X DDS function frequency meter signal generator module

Product 2MHz USB PC Function Generator Brand Velleman Description Overview The PCGU1000 is a digital function generator which can be connected with a PCvia USB. Standard signal waves like e.g. sine, triangle and rectangle areavailable; other sine waves can be easily created. The signal waves arecreated in the PC and produced by the function generator via DDS (DirectDigital wave Synthesis Features Frequency range: from 0.01Hz to 2MHz Crystal-based stability Outputs are galvanically isolated from the PC Low sine wave distortion Two parallel output connectors for waveforms TTL-level synchronisation output Stores up to 8192 of waveform points Standard waveforms: sine, square and triangle Predefined library waveforms included: noise, sweep,... You can create your own waveforms with the integrated signal wave editor Sweep frequency range 0.0001Hz to 25MHz Sweep time 1ms to 10 hours Noise mode bandwidth 25MHz Extended bode plot option together with PC scope Automated wave sequence generation, using file or computer RS232 input DLL available for custom software development System Includes: USB function generator Getting started manual Software on CD USB cable Worldwide charging adaptor Specifications Amplitude range: 100mVpp to 10Vpp @ 1KHz// 600ohm load / 0V offset Frequency setting resolution: 0.01% With internal 40 dB attenuator (output divided by 100) Direct digital wave synthesis (DDS), stores up to 8192 of waveform points Amplitude resolution: 0.4% of full scale Offset: from 0 to -5V or +5V max. (resolution 0.4% of full scale) Vertical resolution: 8 bits (0.4% of full scale) Sample rate: 50MHz Typical sine wave distortion (THD): Output impedance: 2 x 50ohm Power supply: standard 9V DC adapter, 600mA (included) Dimensions: 55 x 190 x 200mm Minimum system requirements: IBM compatible PC Windows™ 98SE, ME, 2000, XP, Vista * SVGA display card (min. 800x600) Mouse Free USB port CD Rom player More Products View More Products

Buy FY6900 Dual Channel DDS Function Arbitrary Waveform Signal Generator Pulse Signal Source Frequency C for R2,346.54

Buy DDS Signal Generator Counter - JDS6600 DDS Signal Source Dual Channel Arbitrary Wave Function Gener for R5,359.00

Buy DDS Signal Generator Counter - JDS6600 DDS Signal Source Dual Channel Arbitrary Wave Function Gener for R3,859.00

Wireless RF Signal Detector CC308 Multi Function Camera Bug GSM Alarm System WiFi GPS Laser Package contains 1 X item of the smallest listed variant.

Buy SGP1002S Digital Signal Generator DDS Function Generator Sine Wave Arbitrary Waveform Frequency Gene for R881.75

Buy 5MHz UDB1005S DDS Signal Generator LCD1602 Sweep Function Source Sine Square T for R1,256.02

Buy XR2206 Signal Function Generator DIY Kits + Case Sine Triangle Square 1Hz-1MHz for R225.00

Buy CC308 Wireless Signal Metal Detector Multi Function Camera Bug GSM Alarm System WiFi GPS for R332.70

Buy 0-50kHz 1W DDS Function Frequency Meter Signal Generator Module With Custom Arb for R649.00