Esp32 aduio kit wifi

Description: Brand: Wemos ESP32 Joystick KIT wifi & bluetooth Module development board For more product information, please click: https://github.com/LilyGO/ESP32-Joystick Package included: 1 x ESP32 Module 1 x Joystick Module 2 x Pin 1 x Cable

Buy M5Stack Core2 ESP32 with Touch Screen Development Board Kit WiFi bluetooth Grap for R923.77

Description:   WIFI Kit series is the new development of the cost-effective networking program, the main chip using ESP32,  LX6 dual-core processor, clocked at 240MHz, computing power up to 600DMIPS, chip built-in 520 KB SRAM, 802.11 b / g / N HT40 Wi-Fi transceiver, baseband, protocol stack and LWIP, integrated dual-mode Bluetooth (traditional Bluetooth and BLE low power Bluetooth).   This product is based on the WIFI Kit 32 added SX1276 chip, that is, LoRa ™ remote modem,  Applicable frequency:8 68MHz and 915MHz  frequency, about -148dBm high sensitivity, +20 dBm power output, high reliability, transmission distance (measured open area communication distance 2.6Km).   Onboard 32MByte Flash, Wi-Fi antenna, 0.96-inch blue OLED display, lithium battery charging circuit and interface, CP2102 USB to serial chip, the perfect support for Arduino development environment, can be very simple and fast for program verification and product development.   Technical Parameters:   Dominant Frequency: 240MHZ Flash: 32M-Bits Processor: for Tensilica LX6 Dual Core Master chip: ESP32 LoRa chip: SX1276 Support frequency band: 868-915MHZ Open communication distance: 2.8KM Computing capacity: up to 600DMIPS Dual-mode Bluetooth: traditional Bluetooth and BLE low-power Bluetooth Development environment: perfect support for Arduino Operating voltage: 3.3-7V Operating temperature range: -40-90 ℃ Receiver sensitivity: -139dBm (SF12, 125KHZ) UDP continuous throughput: 135Mbps USB adapter chip: CP2102 Support mode: Sniffer, Station, softAP and Wi-Fi Direct Transmit power: 19.5dBm@11b, 16.5dBm@11g, 15.5dBm@11n Data rate: 150Mbps @ 11n HT40, 72Mbps @ 11n HT20, 54Mbps @ 11g, 11Mbps @ 11b Note: this item do not have the Lithium battery and antenna. Package included: 1 x SX1276 ESP32 Module        

Description:   1. The main control chip using Le Xin ESP32, Tensilica LX6 dual core processor, clocked at 240MHz, computing capacity of up to 600DMIPS, 520 SRAM, 802.11 KB chip b/g/n HT40 WiFi transceiver,  baseband, and LWIP protocol stack, Bluetooth (Bluetooth dual-mode integrated traditional and BLE low-power Bluetooth). 2. onboard 16 Mt bytes (128 Mt bit), Flash, and Wi-Fi antennas. 3. 0.96 inch White OLED display. 4. lithium battery charging circuit and interface. 5. CP2102 USB to serial chip, perfect support for Arduino development environment ESP32 QFN package is a highly integrated chip, because of high frequency, small volume and not easy to heat dissipation, so Appeared when use high fever is normal, we complete the circuit had done to the stability of the evaluation, please rest assured use; If you have any worry, can increase the heat sink. This product has built-in batteries. Package included: 1 x ESP32 OLED V2.0 Kit( ESP32 OLED V2.0*1, Board*1, DTH12*1, 3D print Shell*1,Cable*1, Line *1, Small heat sink *1, pin*2) 1 x USB Cable

Buy X-8266 ESP-WROOM-02/ ESP32 Rev1 WiFi bluetooth Module OLED IOT Electronics Starter Kit for R423.32