Dot matrix cable face

5Pcs MAX7219 Dot Matrix Module MCU LED Control Module Kit For Arduino Specifications: A single module can drive an 8 x 8 common cathode lattice Operating voltage: 5V Size: 5 x 3.2 x 1.5 cm (L x W x H) LED color: Red With four screws hole, aperture 3mm With input and output interfaces, supports multiple modules cascade Wiring instructions: 1. The module left side as an input port and the output port on the right 2. To control a single module, just connect the input port to the CPU 3. When cascading multiple modules, the input port of the first module connect to the CPU, the output port connect to the input port of the second one, and so on. In the case of 51 MCU: VCC → 5V GND → GND DIN → P22 CS → P21 CLK → P20 Note: 1. VCC and GND is not reversed, it would burn the chip! 2. When the 51 microcontroller P0 port controlling, must be connected to the pull-up resistor, it is recommended that the resistance of 4.7K--10K 3. Please install lattice into the round hole first, and then insert the round hole to PCB board and weld. Face the side of lattice with words, from left to right pin order is 123456. PCB board 1st pin is square pad! 4. Electrolytic capacitors long-pin as positive, short-pin as negative; ceramic capacitor hsa no positive and negative points Package included: 5 x LED module 5 x Dupont line (5P-20cm)

3Pcs MAX7219 Dot Matrix Module MCU LED Control Module Kit For Arduino Specifications: A single module can drive an 8 x 8 common cathode lattice Operating voltage: 5V Size: 5 x 3.2 x 1.5 cm (L x W x H) LED color: Red With four screws hole, aperture 3mm With input and output interfaces, supports multiple modules cascade Wiring instructions: 1. The module left side as an input port and the output port on the right 2. To control a single module, just connect the input port to the CPU 3. When cascading multiple modules, the input port of the first module connect to the CPU, the output port connect to the input port of the second one, and so on. In the case of 51 MCU: VCC → 5V GND → GND DIN → P22 CS → P21 CLK → P20 Note: 1. VCC and GND is not reversed, it would burn the chip! 2. When the 51 microcontroller P0 port controlling, must be connected to the pull-up resistor, it is recommended that the resistance of 4.7K--10K 3. Please install lattice into the round hole first, and then insert the round hole to PCB board and weld. Face the side of lattice with words, from left to right pin order is 123456. PCB board 1st pin is square pad! 4. Electrolytic capacitors long-pin as positive, short-pin as negative; ceramic capacitor hsa no positive and negative points Package included: 3 x LED module 3 x Dupont line (5P-20cm)

MAX7219 Microcontroller 4-in-1 Display Dot Matrix Module For Arduino Specifications: A single module can drive a 8x8 dot matrix common cathode Working voltage: 5V Module size: 12.8 x 3.2 x 1.3 cm (L*W*H) With 64 fixing screw holes, hole diameter: 3mm Module with input and output interfaces, support for cascading multiple modules Wiring: 1. The left side of the module is the input port, and the right is the output port. 2. Control of a single module, the input port only need to receive CPU. 3. The more a module cascade and input end of the first module is connected with the CPU and input end of the input end of the output end is connected to the second module, output terminal of the second module connected with the three modules, and so on. For example: 51 SCM VCC→5V GND→GND DIN→P2.2 CS →P2.1 CLK→P2.0 Package included: 1 x MAX7219 Dot Matrix Module 1 x 5pin Dupont Cable

Buy MAX7219 Dot Matrix MCU LED Display Control Module Kit With Dupont Cable for R210.00

SUPER-RED DOT MATRIX LED DISPLAY; 5x7; 38.50x53.20mm; 5mm DOTS BLACK FACE; WHITE DOTS; VF=2.1V; IF=20mA

LED DOT MATRIX DISPLAY MODULE 16x16 51 UNLIMITED CASCADING 12864 DEVELOPMENT BOARD COMPATIBLE INTERFACE; RED PCB.

SELECTED OPTION: COLOR: PINK CLICK HERE for more options in this item. Description:   This DS3231 clock using Touch Key Control,the Brightness can be adjustable. Of course it also can shows temperature, day, date and important festival!Like New Year's Day,Christmas Day, Valentine's Day and so on.Besides,it has five kinds of switched mode,and you can also select the date of birth, It can show Happy Birthday when the date is coming. 1. Using DS3231 high precision clock chip(with temperature compensation)it can accurately travel time     after powered by backup battery(more accurate than the DS1302 clock chip). 2. Two Touch Key input replace the physical keys,to prevent the long-term press damage.     Long Touch the Menu key you can enter the Menu functions to prevent interference. 3. Four-color optional,you can choose White,Pink,Blue and Green color. 4. PCB Size: 15cm x 8cm.it can shows the big font by the big size. 5. Ideal digital clock DIY kit for electronics enthusiasts, easy to install. 6. Can connect with USB cable for 5V power supply, convenient for use. 7. Designed crystal acrylic shell. 8.  Manual is.   Function:   1. Long Touch the Menu key enter the Menu functions, Short Touch the Next key to select the function. 2. After selecting the function, short touch the Menu key to confirm to enter, after entering also through     Next key to select the change. Touch the Menu key again to confirm the set will switch back to the normal display. 3. The menu has TIME(Set Time), DATE(Setting the date), ALAR(Set the alarm), FONT(set the different font),     DISP(switched mode), MIDP(intermediate second point action), FMT(Set 24-12 format), BRH(Set the date of birth),     BRIG(Set the Brightness). Package included: 1 x  DIY DS3231 Touch Key Control Brightness Adjustable Big Size Dot Matrix Alarm Clock Kit(Without CR1220 battery)

SELECTED OPTION: COLOR: WHITE CLICK HERE for more options in this item. Description:   This DS3231 clock is designed to be completely sealed with an acrylic oval shape, very suitable for display on the desk. Using 4mm size high-brightnesss Dot-Matrix, even in the bright light situation is still clearly visible. It also has five level of brightness adjustable. Both sides of the back have a Touch Key control and with sound feedback to recognize whether the key is touch. Of course, it also can shows temperature, day, date and important festival! Like New Year's Day, Christmas Day, Valentine's Day and so on. Besides, it has five kinds of switched mode, and you can also select the date of birth, It can show Happy Birthday when the date is coming. That makes the clock no longer looks simple. 1, Using DS3231 high precision clock chip(with temperature compensation)it can still accurately travel time after powered by a backup battery(more accurate than the DS1302 clock chip). 2, Two Touch Key input replace the physical keys, to prevent the long-term press damage. Long Touch the Menu key you can enter the Menu functions to prevent interference. 3, Four-color optional, you can choose Red, Blue, Green and White color. 4, Whole Size: 11.7cm*4.2cm*1.6cm. 5, Ideal digital clock DIY kit for electronics enthusiasts, easy to install. 6, Can connect with USB cable 5V for power supply, convenient for use. 7, With the white circuit board it looks more clearly, and designed by crystal acrylic shell. 8, Manual: Function:   1, Long-Touch the Menu key enter the Menu functions, Short Touch the Next key to select the function. 2, After selecting the function, short touch the Menu key to confirm to enter, after entering also through Next key to select the change. Touch the Menu key again to confirm the set will switch back to the normal display. 3, The menu has TIME(Set Time), DATE(Setting the date), ALAR(Set the alarm), FONT(set the different font), DISP(switched mode), MIDP(intermediate second point action), FMT(Set 24-12 format), BRH(Set the date of birth), BRIG(Set the Brightness).   Package included:   1 x  DIY DS3231 Touch Key Precision Hight-Brightness LED Dot Matrix Display Desktop Alarm Clock Kit (Without CR1220 battery)

Mega 2560 Motor Servo RFID Ultrasonic Ranging Starter Kit For Arduino Feature: With mega 2560 module starter kit, fully compatible with Arduino. Is a good choice if you want to learning Arduino. Package includes: 1 x Mega2560 1 x USB cable 1 x 65 jumper 1 x 830 hole breadboard 15 x LED (Red, Green, Yellow each) 30 x Resistance (220R, 10K, 1K each) 1 x 10pin dupont calbe (male to female) 1 x Potentiometer 1 x Active buzzer 1 x Passive buzzer 1 x 74HC595N 1 x Infrared receiving head 1 x LM35DZ 1 x Flame sensor 2 x Roll ball switch 3 x 5mm LDR 5 x Button switch with Cap 1 x IR remote control 1 x One digital tube 1 x Four digital tube 1 x 8*8 dot matrix tube 1 x UNL2003 driver board 1 x 5V stepper motor 1 x SG90 1 x LCD1602 IIC I2C 1 x PS2 game joystick module 1 x DHT11 temperature and humidity sensor module 1 x Water level measurement module 1 x RFID module 1 x RFID key ring 1 x RFID card 1 x Sound sensor module 1 x One channel relay module 1 x RTC module 1 x 16 button matrix keyboard module

Feature: The Compatible Arduino Starter Kit is designed for the new comers to Arduino. We think people will get a deep impression for their electronic knowledge if they can perform DIY things. So this kit includes a lot of discrete components and some interesting and easy to use modules. Through this Kit you can do many interesting projects. From basic simple Arduino project like LED blink to more complex usage like I2C RTC or Infrared remote controlling, just make your thought fly. Package included: 1 x Uno R3 Board 1 x Breadboard 1 x Prototype Shield 1 x 4x4 keypad 1 x 5V relay module 1 x step motor driver 1 x gas sensor 1 x IIC module 1 x sound module 1 x JoyStick 1 x Clock module 1 x servo 1 x stepper motor 1 x LCD1602 1 x IR controller 10 x Push button switch 1 x 7-Segment display(1-digit) 1 x 7-Segment display(4-digit) 1 x Dot Matrix 2 x 10K Potentiometer 1 x Active Buzzer 1 x Passive Buzzer 11 x Color Switch 1 x MAX7219 1 x 74HC595 1 x 4N35 1 x 10uF capacitor 1 x flame sensor 1 x Photo resistor 1 x IR receiver 1 x IR sender 1 x RGB LED 1 x Tilt 1 x LM360Z 1 x Monolithic capacitor 1 x L Shape 40 Pin Header 1 x Straight 40 Pin Header 10 x Green 5mm LED 10 x Red 5mm LED 10 x Yellow 5mm LED 10 x 220R Resistor 10 x 1K Resistor 10 x 10K Resistor 20 x Female-Female cable 20 x Female-male cable 65 x jumper wires 1 x USB cable 1 x 9V battery cable

Features: The most complete performance starter kit with all the essential arduino products. 174 PCS essential Arduino components. Includes lastest Arduino components to turn your idea into a real product. Arduino display includes IIC/I2C interface was developed to reduce the IO port usage on Arduino board Description: Simply the best Arduino kit with most complete components These lessons are old and outdated. Tons of updated lessons and Arduino codes are availabe on Google and Youtube for free! Just make sure that Arduino kit you ordering includes all the parts you need. Parts included in this package: 1 x Compatable Arduino Uno R3 Board 1 x Protoshield 1 x USB Cable for Arduino R3 board 1 x Mini Breadboad for R3 Protoshield Board 1 x 4X Pin Header for Uno R3 Board 1 x I2C Address: 0x27 1 x Infrared Phototransistor 1 x Ball Switch 1 x Infrared Sensor 1 x Infrared Receiver 1 x S8050 Transistor 1 x 5516 LDR Photo Resistor 5 x Color Switch 10 x Green 3mm LED 10 x Red 3mm LED 10 x Yellow 3mm LED 1 x 1k Rotary Switch 1 x 10k Rotary Switch 1 x 100k Rotary Switch 1 x Stepper Motor 1 x Stepper Motor Controller 1 x Sound Sensor 1 x 1 Channel Realy 1 x 9Volt Battery Holder 1 x Distance Sensor 1 x Digital Temp Sensor 10 x Male to Male Dupont Cable 10 x Male to Female Dupont Cable 10 x Female to Female Dupont Cable 1 x 4 Bits Digital Tube LED 1 x 1 Bits Digital Tube LED 1 x 8x8 Dot Matrix Digital Tube 1 x Joystick controller for Arduino 1 x 74HC595IC 1 x Active Buzzer 1 x Passive Buzzer 30 x 300 ohm Resistor 30 x 1K ohm Resistor 30 x 10 ohm Resistor 1 x Straight 40 Pin Header 1 x L Shape 40 Pin Header

Arduino Starter Kit     Please check shipping information before placing an order   General   Compatible with Arduino High quality Board: UNO R3   Package Contents   Arduino UNO R3 Board 400 point Breadboard USB Cable 9V Wall Power Adapter (1A) Remote control for Ardunio 1602 LCD Ardunio Protosheild w/ Mini Breadboard 65 X MM Jumper Wires (assorted length) 4 Pin DuPont Wires SG90 9G Servo Stepper Motor Stepper Motor Driver 100 x Resistors (10 each / 10, 100, 200, 330, 1K, 2K, 5K, 10K, 100K, 1m ohm) 9V Battery 1 Channel Relay Module 8*8 Dot Matrix Module 7 Segment Display (4 digit) 7 Segment Display (1 digit) MPU 6050 Accelerometer and Gyroscope Module XY Joystick Module HCSR04 Ultrasonic Sensor Module Small Plastic Box (with components) 5 x BC547 NPN Transistor 5 x BC557 PNP Transistor 2 x Photoresistor (LDR) 5 x 1N4007 Diodes 5mm LED (5 each / blue, green, yellow, white, red) RGB LED (Common Cathode) 2 x 10K Potentiometer 74HC595 8 Bit Shift Register MAX7219 Chip (LED Driver) Thermistor Piezo Buzzer 5 x 22pF Capacitors 5 x 0.1uF Capacitors 2 x 50V 10uF Capacitors 2 x 50V 100uF Capacitors 5 x Push Button Switches H-Bridge Motor Driver IR Receiver 3V DC Motor 5 x PN2222 Transistors Breadboard Holder 40 PIN Header            

Feature: The Compatible Arduino Starter Kit is designed for the new comers to Arduino. We think people will get a deep impression for their electronic knowledge if they can perform DIY things. So this kit includes a lot of discrete components and some interesting and easy to use modules. Through this Kit you can do many interesting projects. From basic simple Arduino project like LED blink to more complex usage like I2C RTC or Infrared remote controlling, just make your thought fly. We provide some learning lessons for starters, but you can also make your own interesting projects by using the parts of the Kit. Package included: 1 x Compatible UNO R3 board 1 x Breadboard (830 points) 1 x USB cable 1 x 9V battery 1 x Remote control 1 x IIC 1602 LCD 1 x Protoshield with mini breadboard 1 x 65mm jumper wire (assorted length) 1 x 8*8 Dot matrix module 1 x SG90 9G wervo set 1 x Stepper motor 1 x Stepper motor driver 30 x Resistor 1 x 9V Battery connection 1 x 7-Segment display (4 digit) 1 x 7-Segment display (1 digit) 1 x Small plastic box (with component) 1 x Photoresistor (LDR) 25 x 5mm LED (5 each / green, yellow, red) 1 x 10K Potentiometer 1 x 74HC595 8 bit shift register 1 x Thermistor 2 x Piezo buzzer cactive&Passtive) 4 x Push button switche 1 x H-Bridge motor driver 1 x IR receiver 4 x Cap 1 x Pin header

Godox Witstro ADB600 battery flash The Godox Witstro AD600B is an all-in-one 600WS Lithium-ion powered strobe. It is both TTL and HSS enabled and is compatible with Canon and Nikon's 2.4GHz radio receiver units built inside. The AD600 Witstro can be controlled with full manual power control via the recent 2.4GHz X1 transmitter units or master speedlite units like the TT685. What makes this piece of photographic equipment so beneficial is that it also provides the option of a lightweight remote head, which is a feature that has been on the lot on many photographers' lists. A soft case and shoulder strap then provide support for the strobe. To achieve the 1200Ws output you simply attach two AD600 strobes to one 1200Ws head via a 2into1 adapter cable. The remote head is enabled by a cord that simply plugs into the strobe flash tube socket that in turn acts as an extension cord between the strobe and remote flash tube. The Ad600's removable provides a battery health of 500 full power flashes from one charge while the complete strobe in the cordless configuration weighs approximately 2.9kg. Features: Powerful 600Ws Fan Cooled 10W LED Modelling Light (Adjustable) Optional Remote Head (600Ws & 1200Ws Options) Godox and Bowens Mount Versions Built in (removable) 11.1V/8700mAh Lithium-ion Battery Up to 500 Full Power Pops per Battery Charge 0.01 — 2.5 Seconds Recycle Time Flash Modes — TTL/Manual/Multi HSS to 1/8000th Second Curtain Sync FEC/FEB — 1/3rd Increments (+ Stops) FEL (Flash Exposure Lock) Manual Flash — 1/256 — 1/1 Outdput (1/3rd Increments) Godox 2.4GHz x Radio System ETTL & ITTL Radio Slave Modes (Auto Switching) Range — 100m + with X1 as Transmitter Groups — A/B/C 32 Channels Supports Legacy Godox FT-16 Remote Manual Trigger System Support Godox XT-16 Remote Manual Trigger System Canon & Nikon Optic Wireless Slave Modes Groups — A/B/C 4 Channels S1 & S2 Optics Slave Modes Flash Duration — 1/220s — 1/1000s Large Dot Matrix LCD Display Custom Functions Auto Memory Function Micro USB Port for Firmware Upgrades USB Communication Port (for FTR-16 & XTR-16 Receivers 3.5mm Sync Port Included: 1 x Godox Witstro AD600 head with battery 1 x Protective cover 1 x Charger

 Specifications: Receiver: L1Type, C/A Code Capture channel: 51 Tracking channel: 1 Maximum update frequency: 10 Hz Display: pixel  height * width   128 x 64 dot matrix Size: 65mmx 52mmx 21mm Weight: 39.6g (With the battery) Memory: 512KB Key: 3 function keys Location: 10m (Support the difference correction system area up to 2 meters) Speed: 0.1m/s The initial positioning time: Hot start: About 5 seconds Warm start: About 40 seconds Cold start: About 2 Minutes Sensitivity:-161dBm tracking/ -157dBm re capture/ -148dBm capture Data protocol: NMEA-0183 v3.0 The power supply voltage: USB DC 5 V / 3.7 V  390 Ma the built-in lithium battery The operation time: approximately 6 hours Power waste: Capture: about 70 Ma Continuous tracking: about 30 Ma Storage temperature:  -30°C to +85°C Working temperature: -20°C to +75°C Humidity: Up to 80% non-condensing Range of use: This product only work under outdoor sky open areas around elevation 15 ° no building cases to receive satellite signals!   Note: Built-in GPS Module, it's the best choice to climb the mountain or forests!  However most of other GPS trackers need to install a SIM card, which will be no signal in mountain. Kindly noted that use it in opean areas without obstacle,  it takes a whiletime to get the satellite signal.   Color  Green (As in the picture)   Package includes: 1 x Mini gps tracker 1 x USB cable 1 x Instructions 1 x Retail Box