Custom x board kit

DIY TDA2030A Audio Amplifier Board Kit Mono Power 18W DC 9V-24V Features: TDA2030A is widely used as Hi-Fi amplifier manifold in many computer active speakers. Easy Installation. It has the function of thermal shutdown, current limiting. Minimum transmission distortion Specifications: Output power: Maximum 18W Supply voltage: DC 9V-24V (recommended DC 12V, this voltage to the heat sink requirements are very low;) Maximum supply of this board is actually up to 40V, but you need to change the board's own electrolytic capacitor C1, the capacitor voltage value is higher than supply voltage can be use.) Quiescent current: about 25mA (disconnect to tone, connect to 8Ω speaker, 12V power supply.) Speaker impendance: 4Ω-8Ω Total harmonic distortion: THD 0.08% (Po=0.1 to 14W, RL=4Ω) SNR: 94dB-106dB (1W-15W) Heat: The higher the supply voltage, the great the volume, the higher the heat Note: This is DIY kit, you need to solder it by yourself! Package includes: 1 x DIY TDA2030A Audio Amplifier Board Kit

20pcs DIY LM386 Ultra Mini Mini Power Amplifier Board Kit Low Power Consumption 3~12V Package contains 1 X item of the smallest listed variant.

VST29 HD AV VGA LVDS Inverter LCD Driver Board Kit With Remote Controller Package contains 1 X item of the smallest listed variant.

Motor: Motor diameter: 49 MM Motor Height: 35 MM Motor shaft diameter: 3.17 MM (with a worm) Output shaft length: 18 MM Weight: 212 g Wiring length: about 150MM Driving voltage: one group 24V, one group 5V, and one group pulse Note: Do not connect the polarity wrongly, or it will damage the motor. Package included: 1 x Motor 1 x Driver Board

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Feature: Two-color LED strobe fun DIY kit parts produced. Simple and practical, easy installation, low power consumption. Technical specifications: Product Name: DIY Flash Kit Color: Two color in random Dimensions: 9x3cm / 3.54 "x1.18" Voltage: 3-5V Package Included: 3 x Flash Kit DIY (with battery box) 3 x Instructions 3pcs DIY Two-color LED Flashlight Electronic Kit Circuit Board 3pcs DIY Two-color LED Flashlight Electronic Kit Circuit Board 3pcs DIY Two-color LED Flashlight Electronic Kit Circuit Board

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Features: Kit name: Clap switch kit Working voltage: 4.5-5.5V PCB size: 27 x 49mm Kit function: Clap hand once, LED lit, and then clap once again LED turn off, so the cycle. Features: high sensitivity, about 4 meters clap can control. Note: This is a DIY kit, you need to assemble it. Package includes: 1 x PCB board 1 x MIC microphone head 1 x KF301-2P terminal block 1 x 47UF25V electrolytic capacitor 1 x 0.1UF50V electrolytic capacitor 4 x 104 monolithic capacitor 5 x 9013 transistor 1 x Colorful LED 2 x 1N4148 diode 1 x 510ohm resistance 8 x 4.7K resistance 6 x 10K resistance 1 x 750K resistance Voice Control Clap Switch Module Kit High Sensitive LED Rhythm Bistable Switch DIY Kit Voice Control Clap Switch Module Kit High Sensitive LED Rhythm Bistable Switch DIY Kit Voice Control Clap Switch Module Kit High Sensitive LED Rhythm Bistable Switch DIY Kit

Features: Kit name: Clap switch kit Working voltage: 4.5-5.5V PCB size: 27 x 49mm Kit function: Clap hand once, LED lit, and then clap once again LED turn off, so the cycle. Features: high sensitivity, about 4 meters clap can control. Note: This is a DIY kit, you need to assemble it. Quantity: 10 DIY kits Package includes: (per kit) 1 x PCB board 1 x MIC microphone head 1 x KF301-2P terminal block 1 x 47UF25V electrolytic capacitor 1 x 0.1UF50V electrolytic capacitor 4 x 104 monolithic capacitor 5 x 9013 transistor 1 x Colorful LED 2 x 1N4148 diode 1 x 510ohm resistance 8 x 4.7K resistance 6 x 10K resistance 1 x 750K resistance

Buy Realacc Carbon Fiber Battery Protection Board with Tie Down Strap for X Frame kit for RC Drone FPV R for R82.69

Instructions phone calls lights: Phone calls phone calls lights kit can be used to sense the GSM signal display, sensing distance up to 1 m, is a very interesting DIY module. Electrical characteristics: Supply voltage: 3 to 12V Sensing distance: about 1 m PCB board size: 2.2cm * 2.8cm Scope: GSM mobile phone signal, for CDMA phones are useless Note: This is a DIY kit, you need to assemble it. The circuit theory: The main circuit is amplified antenna sensor signal circuit and circuit. Sensing signal through the antenna 3 to S8050 transistor amplifier to drive the LED, so that light up. When no signal is detected, no calls or no GSM phones, LED circuit is not only detects the signal to light up LED. Inductance of production: Inductance 0.25 to 0.5MM enameled available in pen core above can be around 5-10 laps. After a good round with a blade to scrape paint inductor 2, so we go soldered to the board. Package includes: 5 x DIY Kit

KIT CONTENTS:(2)Backdrop Support Stand, (4)Cross Bar, (3)1.8 X 2.8 meters Fabric Backdrop(White, Black, Green), (3)Backdrop Clips, (1) Carrying bag BACKDROP SUPPORT SYSTEM: The background stand is adjustable up to 8.5 feet tall by 10 feet wide. Made from aluminum alloy with a professional black stain finish BACKGROUND: Fabric. Finished along all edges to prevent tears. It is perfect for television, video production and digital photography BACKGROUND CLIPS: It is perfect to hang backdrop or something you need onto a support system with good and sturdy grip CARRYING BAG: Carrying bag in custom design for background support kit and photography accessories

- CNC Shield Board Version: 3.0 Color: Red Size(L*W*H): 68 x 53 x 18 mm Voltage: DC 12~36 V (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) Features: 1. Uses removable A4988 or DRV8825 compatible stepper drivers. 2. The extension board can be used for carving machine, 3 d printer driver expansion board 3. GRBL 0.8 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4. PWM Spindle and direction pins,4-Axis support (X, Y, Z, A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 5. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. 6. Please note that this is an unassembled kit and Basic soldering skills are needed. - A4988 Stepper Motor Driver Color: Red Size(L*W*H): 20 x 15 x 10 mm Thermal shutdown circuitry: Yes Crossover-current protection: Yes Ground fault protection: Yes Load short-circuit protection: Yes Compatible logic supply: 3.3V and 5 V Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16 Features: 1. Mix with slow current decay modes. 2. Internal UVLO and Low RDS (On) Output. 3. Automatic current decay mode detection/selection. 4. Synchronous rectification for low power dissipation. 5. Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. - Uno R3 Board MCU: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: 40 mA max 3.3 V output current: 150 mA max Digital I/O pins: 14 (including 6 with PWM capability) Analog input pins: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash memory: 32 kB Size(L*W*H): 68 x 53 x 10 mm Click to download universal course Package included: 1 x Uno R3 Board 1 x CNC Shield Board 4 x A4988 Stepper Motor Driver 4 x Heat Sink 1 x USB Cable 1 x 40-Pin Row Needles

- CNC Shield Board Version: 3.0 Color: Red Size(L*W*H): 68 x 53 x 18 mm Voltage: DC 12~36 V (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) Features: 1. Uses removable A4988 or DRV8825 compatible stepper drivers. 2. The extension board can be used for carving machine, 3 d printer driver expansion board 3. GRBL 0.8 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4. PWM Spindle and direction pins,4-Axis support (X, Y, Z, A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 5. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. 6. Please note that this is an unassembled kit and Basic soldering skills are needed. - A4988 Stepper Motor Driver Color: Red Size(L*W*H): 20 x 15 x 10 mm Thermal shutdown circuitry: Yes Crossover-current protection: Yes Ground fault protection: Yes Load short-circuit protection: Yes Compatible logic supply: 3.3V and 5 V Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16 Features: 1. Mix with slow current decay modes. 2. Internal UVLO and Low RDS (On) Output. 3. Automatic current decay mode detection/selection. 4. Synchronous rectification for low power dissipation. 5. Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. - Uno R3 Board MCU: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: 40 mA max 3.3 V output current: 150 mA max Digital I/O pins: 14 (including 6 with PWM capability) Analog input pins: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash memory: 32 kB Size(L*W*H): 68 x 53 x 10 mm Click to download universal course Package included: 3 x CNC Shield + UNO R3 Board + 4x A4988 Driver Kit

Planet Waves - PWGPKIT10 CS Pedal Board Patch Kit Planet Waves solderless cable kits are the ultimate solution for custom wiring pedal boards, rack gear, and your entire layout from guitar to amp. Say good bye to messy, unreliable wiring and say hello to custom cut cable lengths that perfectly suit your needs. Planet Waves plugs and cables provide the most accurate and reliable sound reproduction, from guitar, to amp, and all points in between. Many of Planet Waves most notable artists use the solderless cable kits as their primary pedalboard and rack wiring solution.

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: This Starter Kit is based on UNOS R3 development board. It includes the most basic component, such as bread board, breadboard wires, LED lights, resistance. Note: Packing with carton box. Package included: 1 x Components storage 1 x UNO R3 1 x Breadboard 15 x LED (5 x Red, 5 x Blue, 5 x Yellow) 8 x Resistance (220 Ohm) 30 x Colorful breadboard wire 1 x USB cable 1 x UNO R3 Geekcreit UNO R3 Development Board Starter Kit Basic Kit For Arduino DIY Geekcreit UNO R3 Development Board Starter Kit Basic Kit For Arduino DIY Geekcreit UNO R3 Development Board Starter Kit Basic Kit For Arduino DIY

Description: - This Arduino uno development kit, is designed based on the Arduino uno board, together with 2-channel & 16-channel servo shield board to drive the tank and 2WD car. In addition, There has wireless contoller and receiver, you can control the tank car via wireless control. - Provide source code, APP, and manual. Specifications: About Active Buzzer: - Size: 3.2cm * 1.3cm - Module Interface Description: 1. VCC external 3.3V-5V voltage (which can be connected directly with the 5v microcontroller and 3.3v microcontroller) 2. GND External GND 3. I/O external microcontroller IO port About Arduino Uno Development Kit: Description: - The Arduino Uno Development Kit, with the ability to control 2 motors and 16 servos at the same time, is ideal for developing mobile robots such as robotic arms, trolleys, tank chassis and more. - This set of development board is based on ESP8266 development and is compatible with Arduino UNO R3. - It can control 2 motors and 16 servos at the same time. It is suitable for mobile robot driving control with a robotic arm. ESPduino is an Arduino board with WiFi function. Features: - Can control 2-way motor and 16-way servo at the same time; - Using Bluetooth (reserved in-line interface) or WiFi control; - Using plug-in design. Power connection method: - Disconnect VM and VIN, (separate control motor, 6 ~ 36V); - Open circuit VS and VIN, (control servo separately, 6 ~ 18V); - Short circuit VM and VIN while shorting VS and 5V. At the same time control the motor (6 ~ 18V) and 16 5V servos. Package Included: 1 x 2-channel motor&16-channel servo shield board 1 x UNO board 1 x USB Cable 1 x Wireless controller 1 x Receiver 1 x Active buzzer 1 set Copper pillar kit 1 x 18650 Battery box 1 x Dupont line