Clearline board single

Buy Clearline DB Board Single Phase SS25 Surge Arrestor for R304.74

Buy Clearline DB Board Single Phase SS40P Surge Arrestor for R419.09

Buy Low Pass Filter Bass Subwoofer Preamp Amplifier Board Single Power DC 9-32V Preamplifier with Bass V for R310.00

Sherlo Single Pole Dry Contact Relay Board 12 - 16V AC/DC:ￂﾠSingle Pole Dry contact Relay board 12 - 16V AC/DC input N.O / N/C / COMMON LED indication e&oe ￂﾠsherlo, relay board

Buy Single Power Supply DC10-24V 22Hz-300Hz Subwoofer Preamp Board Low Pass Filter Module for R190.91

Centurion Single VANTAGE 500 - Max Leaf Width 4.0m, 310kg Kit Kit includes: Operator, Mounting Hardware, Controller, Wall Box with 2A SM Charger, 7Ah Battery, Mains Isolator, LED External Indicator Board, 2 x 4 Button NOVA Tx e&oe centurion, vantage 500, gate motor, swing gate, motors

Description PCB FG SS P1015 | Single Sided PC Board Single Sided PC Board • Fibre Glass • 10 x 15cm More Information View More Information More Products View More Products

5pcs 1CH 12V 30A Relay Module High Power Relay Control Board Single Switch

Buy 1CH 12V 30A Relay Module High Power Relay Control Board Single Switch for R219.00

SINGLE SIDED PHENOLIC 1.6MM PROTOTYPING BOARD / FOR 2 x 5 TO 20 PIN DIPS

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over half a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. There's even a volume trim pot so you can adjust the volume on the board down from the default 24dB gain. This board is a welcome upgrade to basic "LM386" amps! CJMCU The A+ and A- inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the Audio- pin to ground. The output is "Bridge Tied" - that means the output pins connect directly to the speaker pins, no connection to ground. The output is a high frequency 250KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly. CJMCU Comes with a fully assembled and tested breakout board. We also include header to plug it into a breadboard and a 3.5mm screw-terminal blocks so you can easily attach/detach your speaker. You will be ready to rock in 15 minutes! Features: - Output Power: 2.5W at 4Ω, 10% THD, 1.5W at 8Ω, 10% THD, with 5.5V Supply - 50dB PSRR at 1KHz - Filterless design, with ferrite bead + capacitors on output. - Fixed 24dB gain, onboard trim potentiometer for adjusting input volume. - Thermal and short-circuit/over-current protection - Low current draw: 4mA quiescent and 1uA in shutdown mode Note: Speaker is not included, use any 4 ohm or greater impedance speaker. Package included: 10 x Audio Power Amplifier 10pcs CJMCU-832 PAM8302 Single Channel Class D Audio Power Amplifier Development Board For Arduino 10pcs CJMCU-832 PAM8302 Single Channel Class D Audio Power Amplifier Development Board For Arduino 10pcs CJMCU-832 PAM8302 Single Channel Class D Audio Power Amplifier Development Board For Arduino

FR4 100x70mm Single Side Copper Clad Laminate PCB Board Fiberboard CCL Specification: Panel Size: Approx. 100mm X 70mm or 3.94" X 2.75" (inch) Thickness: 0.06" ±0.005 (1.5mm ± 0.15) Weight: Approx. 23g each Layers: Single Side Panel: FR4 Operating temperature: Up to 140 °C or 285°F Description: This Single PCB Copper Clad Laminate Board is made of copper foil by the hot-pressing technology. Super-fine steel-wool, Restore4, Tarn-X, roscherite, Zap or similar before using. After that be sure to rinse and dry so without any water spots. Combined resin with reinforced material. As basic material of PCB production. Package included: 1 x Single Side Copper Clad Laminate

FR4 70x50mm Single Side Copper Clad Laminate PCB Board Glass Fiberboard CCL Specification: Panel Size: Approx. 70mm x 50mm or 2.75" x 1.96" Thickness: 0.06" ±0.005 (1.5mm ± 0.15) Weight: Approx. 14g each Layers: Single Side Panel: FR4 Operating Temperature: Up to 140 °C or 285°F Description: This Single PCB Copper Clad Laminate Board is made of copper foil by the hot-pressing technology. Super-fine steel-wool, Restore4, Tarn-X, roscherite, Zap or similar before using. After that be sure to rinse and dry so without any water spots. Combined resin with reinforced material. As basic material of PCB production. Package included: 1 x Single Side Copper Clad Laminate

FR4 180x120mm Single Side Copper Clad Laminate PCB Circuit Board CCL Specification: Panel Size: Approx.180mm x 120mm or 7.09" x 4.73" (inch) Thickness: 0.06" ±0.005 (1.5mm ± 0.15) Weight: Approx.58g Layers: Single Side Panel: FR4 Operating temperature: Up to 140 °C or 285°F Description: This Single PCB Copper Clad Laminate Board is made of copper foil by the hot-pressing technology. Super-fine steel-wool, Restore4, Tarn-X, roscherite, Zap or similar before using. After that be sure to rinse and dry so without any water spots. Combined resin with reinforced material. As basic material of PCB production. Package included: 1 x Single Side Copper Clad Laminate

Buy 30pcs 7x10cm Single Sided Copper PCB Board FR4 Fiberglass Board for R464.77