Class above rest

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over half a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. There's even a volume trim pot so you can adjust the volume on the board down from the default 24dB gain. This board is a welcome upgrade to basic "LM386" amps! CJMCU The A+ and A- inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the Audio- pin to ground. The output is "Bridge Tied" - that means the output pins connect directly to the speaker pins, no connection to ground. The output is a high frequency 250KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly. CJMCU Comes with a fully assembled and tested breakout board. We also include header to plug it into a breadboard and a 3.5mm screw-terminal blocks so you can easily attach/detach your speaker. You will be ready to rock in 15 minutes! Features: - Output Power: 2.5W at 4Ω, 10% THD, 1.5W at 8Ω, 10% THD, with 5.5V Supply - 50dB PSRR at 1KHz - Filterless design, with ferrite bead + capacitors on output. - Fixed 24dB gain, onboard trim potentiometer for adjusting input volume. - Thermal and short-circuit/over-current protection - Low current draw: 4mA quiescent and 1uA in shutdown mode Note: Speaker is not included, use any 4 ohm or greater impedance speaker. Package included: 10 x Audio Power Amplifier 10pcs CJMCU-832 PAM8302 Single Channel Class D Audio Power Amplifier Development Board For Arduino 10pcs CJMCU-832 PAM8302 Single Channel Class D Audio Power Amplifier Development Board For Arduino 10pcs CJMCU-832 PAM8302 Single Channel Class D Audio Power Amplifier Development Board For Arduino

Due to some influencing factors (such as brightness of the monitor, etc.), there are some differences lay between photos and actual goods. The measurement we mentioned above is only for your reference. Please allow 2-3cm measurement error.

Description: This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over half a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. There's even a volume trim pot so you can adjust the volume on the board down from the default 24dB gain. This board is a welcome upgrade to basic "LM386" amps! CJMCU The A+ and A- inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the Audio- pin to ground. The output is "Bridge Tied" - that means the output pins connect directly to the speaker pins, no connection to ground. The output is a high frequency 250KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly. CJMCU Comes with a fully assembled and tested breakout board. We also include header to plug it into a breadboard and a 3.5mm screw-terminal blocks so you can easily attach/detach your speaker. You will be ready to rock in 15 minutes! Features: - Output Power: 2.5W at 4Ω, 10% THD, 1.5W at 8Ω, 10% THD, with 5.5V Supply - 50dB PSRR at 1KHz - Filterless design, with ferrite bead + capacitors on output. - Fixed 24dB gain, onboard trim potentiometer for adjusting input volume. - Thermal and short-circuit/over-current protection - Low current draw: 4mA quiescent and 1uA in shutdown mode Note: Speaker is not included, use any 4 ohm or greater impedance speaker. Package included: 3 x Audio Power Amplifier

Description: This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over half a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. There's even a volume trim pot so you can adjust the volume on the board down from the default 24dB gain. This board is a welcome upgrade to basic "LM386" amps! CJMCU The A+ and A- inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the Audio- pin to ground. The output is "Bridge Tied" - that means the output pins connect directly to the speaker pins, no connection to ground. The output is a high frequency 250KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly. CJMCU Comes with a fully assembled and tested breakout board. We also include header to plug it into a breadboard and a 3.5mm screw-terminal blocks so you can easily attach/detach your speaker. You will be ready to rock in 15 minutes! Features: - Output Power: 2.5W at 4Ω, 10% THD, 1.5W at 8Ω, 10% THD, with 5.5V Supply - 50dB PSRR at 1KHz - Filterless design, with ferrite bead + capacitors on output. - Fixed 24dB gain, onboard trim potentiometer for adjusting input volume. - Thermal and short-circuit/over-current protection - Low current draw: 4mA quiescent and 1uA in shutdown mode Note: Speaker is not included, use any 4 ohm or greater impedance speaker. Package included: 10 x Audio Power Amplifier

Description: This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over half a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. There's even a volume trim pot so you can adjust the volume on the board down from the default 24dB gain. This board is a welcome upgrade to basic "LM386" amps! CJMCU The A+ and A- inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the Audio- pin to ground. The output is "Bridge Tied" - that means the output pins connect directly to the speaker pins, no connection to ground. The output is a high frequency 250KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly. CJMCU Comes with a fully assembled and tested breakout board. We also include header to plug it into a breadboard and a 3.5mm screw-terminal blocks so you can easily attach/detach your speaker. You will be ready to rock in 15 minutes! Features: - Output Power: 2.5W at 4Ω, 10% THD, 1.5W at 8Ω, 10% THD, with 5.5V Supply - 50dB PSRR at 1KHz - Filterless design, with ferrite bead + capacitors on output. - Fixed 24dB gain, onboard trim potentiometer for adjusting input volume. - Thermal and short-circuit/over-current protection - Low current draw: 4mA quiescent and 1uA in shutdown mode Note: Speaker is not included, use any 4 ohm or greater impedance speaker. Package included: 5 x Audio Power Amplifier

Fondi OnReal Camera - 8MP Photo Capture, 1080P 30FPS Full HD Video Quality, Built-in Wi-Fi, 120 degree Wide Viewing Angle, 400mAh Lithium-ion Rechargeable Battery, Compatible with Android 4.0 and above and iOS 7.0 and Above - White, Retail Box, 1 year Limited Warranty Product Overview The Fondi OnReal Cam is a small,lightweight, fun and entertainment digital fashion technology gadget which is essentially a wearable camera, similar to the GoPro or the HTC ReCamera, which allows you to capture and share real time videos and photos onto various social media platforms and features a smooth surface and weighs less than 25 grams. In terms of specifications, the device comes with the capability of recording Full HD videos at a resolution of 1080 pixels, through its 8-megapixel CMOS sensor. Users must add up to 32GB of Class 10 memory to the device through the microSD card slot to operate this device. With its unique shape, design this unit is currently available in Black or White colour options in South Africa. The OnReal Cam also comes with accessories such as magnet, adhesive mount, suction cup and clip, inside the box, so if you are looking for a compact device that can shoot your road trips or your extreme sports adventures, but are on a budget, the Fondi OnReal Cam could do the trick. The Fondi OnReal Cam is compatible with both Android and iOS devices and it connects to smartphones and tablets through Wi-Fi. In order to connect the OnReal camera to your smartphone, all you need to do is download the Fondi OnReal app from either the Apple App Store or Google Play, install the app, connect to a wireless network called "OnReal", enter the password to connect and you are good to go. Highlights ¿ Built-in Wi-Fi ¿ 120¿ Wide Viewing Angle ¿ Battery: 400mAh Lithium-ion Rechargeable Battery ¿ Battery Life: 1 Hour (Wi-Fi Mode Off) ¿ Video Quality: 1080P, 30FPS ¿ Photo Capture: 8 Mega Pixels ¿ Time Lapse at 1/5/10/30/60 Second Intervals ¿ Compatibility: Android 4.0 and Above and iOS 7.0 and Above ¿ Class 10 Micro SD Card Slot up to 32 GB (Sold Separately) ¿ Accessories: Magnet, Clip, Suction Pad and Adhesive Mount, ¿ Velvet Pouch ¿ USB Cable ¿ Compatibility: Android 4.0 and Above and iOS 7.0 and Above Please Note The Fondi OnReal Cam does not have any Internal memory, a MicroSD Flash memory card with Class 10 with size up to 32GB must be purchased separately to operate this device.

Fondi OnReal Camera - 8MP Photo Capture, 1080P 30FPS Full HD Video Quality, Built-in Wi-Fi, 120 degree Wide Viewing Angle, 400mAh Lithium-ion Rechargeable Battery, Compatible with Android 4.0 and above and iOS 7.0 and Above - White, Retail Box, 1 year Limited Warranty Product Overview The Fondi OnReal Cam is a small,lightweight, fun and entertainment digital fashion technology gadget which is essentially a wearable camera, similar to the GoPro or the HTC ReCamera, which allows you to capture and share real time videos and photos onto various social media platforms and features a smooth surface and weighs less than 25 grams. In terms of specifications, the device comes with the capability of recording Full HD videos at a resolution of 1080 pixels, through its 8-megapixel CMOS sensor. Users must add up to 32GB of Class 10 memory to the device through the microSD card slot to operate this device. With its unique shape, design this unit is currently available in Black or White colour options in South Africa. The OnReal Cam also comes with accessories such as magnet, adhesive mount, suction cup and clip, inside the box, so if you are looking for a compact device that can shoot your road trips or your extreme sports adventures, but are on a budget, the Fondi OnReal Cam could do the trick. The Fondi OnReal Cam is compatible with both Android and iOS devices and it connects to smartphones and tablets through Wi-Fi. In order to connect the OnReal camera to your smartphone, all you need to do is download the Fondi OnReal app from either the Apple App Store or Google Play, install the app, connect to a wireless network called "OnReal", enter the password to connect and you are good to go. Highlights • Built-in Wi-Fi • 120∘ Wide Viewing Angle • Battery: 400mAh Lithium-ion Rechargeable Battery • Battery Life: 1 Hour (Wi-Fi Mode Off) • Video Quality: 1080P, 30FPS • Photo Capture: 8 Mega Pixels • Time Lapse at 1/5/10/30/60 Second Intervals • Compatibility: Android 4.0 and Above and iOS 7.0 and Above • Class 10 Micro SD Card Slot up to 32 GB (Sold Separately) • Accessories: Magnet, Clip, Suction Pad and Adhesive Mount, • Velvet Pouch • USB Cable • Compatibility: Android 4.0 and Above and iOS 7.0 and Above Please Note The Fondi OnReal Cam does not have any Internal memory, a MicroSD Flash memory card with Class 10 with size up to 32GB must be purchased separately to operate this device.

IN STOCK at supplier. If ordered before 12PM: DELIVERED next day (main centres) or 2-3 days (regional areas or large items) COLLECTION from Geewiz Same Day (aprox 4pm) PRODUCT DESCRIPTION Road safety is important. Transcend's DrivePro 110 dashcam utilizes a Sony image sensor to provide high-resolution images with extremely fine tonal gradation even in low light. In addition, the DrivePro 110 features a built-in battery, a handy snapshot button, emergency recording, headlight reminder, and driver fatigue alert. F/2.0 Aperture and high-quality 6 glass camera lens Wide 130° viewing angle with Sony high-sensitivity imaging sensor for clear and smooth 1080p (30fps) recordings Li-Polymer battery with Auto Power On/Off feature 2.4" Color LCD Built in speaker and microphone Snapshot function Parking monitoring mode Headlight reminder Driver fatigue alert Exclusive DrivePro Toolbox software Built-in G-Sensor detects an impact during recording Sony high-sensitivity image sensor The DrivePro 110 uses a Sony sensor to capture high-resolution images with superb, rich color even in low light. Its built-in Wide Dynamic Range (WDR) technology balances the light and dark areas of captured images, ensuring that every critical shot is as clear as possible. Built-in battery A built-in Li-Polymer battery ensures uninterrupted power to the device. Video will continue to be recorded and stored in the event of an accident or when the engine is off. Handy snapshot function The snapshot button allows you to take photos while still recording video. During an incident, you can remove the DrivePro 110 from the vehicle to create a photographic record of collision damage. Emergency recording In the event of a collision, the DrivePro 110's motion G-sensor detects the impact and triggers emergency recording mode. This prevents overwriting of the file being recorded at the time. This feature can also be manually activated by pressing the red button on the side of the unit. 24/7 Guardian In addition to on-the-road safety, the DrivePro 110 stands sentry when the vehicle is parked. Enabling time-lapse video recording means you can get right to the heart of the matter without needing to view hours of incident-free footage. Note: This feature requires external power supply after the car engine is switched off. Headlight reminder When the DrivePro detects poor lighting conditions, for example at dusk, or in dark places such as a tunnel and basement, the headlight reminder will automatically activate. Driver fatigue alert To help prevent tired drivers from getting into an accident, the driver fatigue alert regularly reminds the driver of the need to rest after driving for a preset, driver-determined period of time. Exclusive DrivePro Toolbox software In addition to playback, Transcend's DrivePro Toolbox features a sorting function to quickly locate video clips by file name, recording date, or group. The DrivePro Toolbox also provides a screenshot function allowing for the capture of a single frame. MLC-based microSD card included The DrivePro 110 comes bundled with a Transcend 16GB High Endurance memory card built of top-tier MLC NAND flash chips, and tested under harsh environmental conditions. It can operate in temperatures from -25° to 85°C, providing consistent long-life durability and endurance. PRODUCT SPECIFICATIONS Dimensions 70.2 × 63.1 × 32.5mm  Weight 71g  Display Type and Size 2.4" color LCD Lens F/2.0, 130° wide angle USB Slot micro USB G-Sensor 3-axis Microphone Built-in Speaker Built-in Battery Built-in Li-Polymer Resolution/Frame Rate Full HD 1920x1080P (30fps) HD 1280x720P (30fps) Video Formats H.264 (MOV: up to 1920x1080 30fps) Memory Card Support 8GB-128GB MLC-based microSD card (Class 10 or above) Connection Interface USB 2.0 Power Supply Input: DC 12V~24V Output: DC 5V 1A Operating Temperature -20°C (-4°F) ~ 65°C (149°F) Storage Temperature -25°C (-13°F) ~ 70°C (158°F) Certificates CE, FCC, BSMI, KC Package Contents DrivePro 110 Car mount Car lighter adapter 16GB High Endurance microSDHC memory card System Requirements Desktop or notebook computer with a USB port, and one of the following operating systems: Microsoft Windows 7 Microsoft Windows 8 Microsoft Windows 10 Mac OS X 10.8.2 or later Linux Kernel 2.6.38 or later

Fondi OnReal Camera - 8MP Photo Capture, 1080P 30FPS Full HD Video Quality, Built-in Wi-Fi, 120 degree Wide Viewing Angle, 400mAh Lithium-ion Rechargeable Battery, Compatible with Android 4.0 and above and iOS 7.0 and Above -Black, Retail Box, 1 year Limited Warranty Product Overview The Fondi OnReal Cam is a fun and entertainment digital fashion technology gadget which is essentially a wearable camera, similar to the GoPro or the HTC ReCamera, which allows you to capture and share real time videos and photos onto various social media platforms and features a smooth surface and weighs less than 25 grams. In terms of specifications, the device comes with the capability of recording Full HD videos at a resolution of 1080 pixels, through its 8-megapixel CMOS sensor. Users can add up to 32GB of memory to the device through the microSD card slot. With its unique shape, design this unit is currently available in Black or White colour options in South Africa. The OnReal Cam also comes with accessories such as magnet, adhesive mount, suction cup and clip, inside the box, so if you are looking for a compact device that can shoot your road trips or your extreme sports adventures, but are on a budget, the Fondi OnReal Cam could do the trick. Please Note The Fondi OnReal Cam is compatible with both Android and iOS devices and it connects to smartphones and tablets through Wi-Fi. In order to connect the OnReal camera to your smartphone, all you need to do is download the Fondi OnReal app from either the Apple App Store or Google Play, install the app, connect to a wireless network called "OnReal", enter the password to connect and you are good to go. Highlights ¿ Built-in Wi-Fi ¿ 120¿ Wide Viewing Angle ¿ Battery: 400mAh Lithium-ion Rechargeable Battery ¿ Battery Life: 1 Hour (Wi-Fi Mode Off) ¿ Video Quality: 1080P, 30FPS ¿ Photo Capture: 8 Mega Pixels ¿ Time Lapse at 1/5/10/30/60 Second Intervals ¿ Compatibility: Android 4.0 and Above and iOS 7.0 and Above ¿ Class 10 Micro SD Card Slot up to 32 GB (Sold Separately) ¿ Accessories: Magnet, Clip, Suction Pad and Adhesive Mount, ¿ Velvet Pouch ¿ USB Cable ¿ Compatibility: Android 4.0 and Above and iOS 7.0 and Above Please Note The Fondi OnReal Cam does not have any Internal memory, a MicroSD Flash memory card with Class 10 with size up to 32GB must be purchased separately to operate this device

Fondi OnReal Camera - 8MP Photo Capture, 1080P 30FPS Full HD Video Quality, Built-in Wi-Fi, 120 degree Wide Viewing Angle, 400mAh Lithium-ion Rechargeable Battery, Compatible with Android 4.0 and above and iOS 7.0 and Above -Black, Retail Box, 1 year Limited Warranty Product Overview The Fondi OnReal Cam is a fun and entertainment digital fashion technology gadget which is essentially a wearable camera, similar to the GoPro or the HTC ReCamera, which allows you to capture and share real time videos and photos onto various social media platforms and features a smooth surface and weighs less than 25 grams. In terms of specifications, the device comes with the capability of recording Full HD videos at a resolution of 1080 pixels, through its 8-megapixel CMOS sensor. Users can add up to 32GB of memory to the device through the microSD card slot. With its unique shape, design this unit is currently available in Black or White colour options in South Africa. The OnReal Cam also comes with accessories such as magnet, adhesive mount, suction cup and clip, inside the box, so if you are looking for a compact device that can shoot your road trips or your extreme sports adventures, but are on a budget, the Fondi OnReal Cam could do the trick. Please Note The Fondi OnReal Cam is compatible with both Android and iOS devices and it connects to smartphones and tablets through Wi-Fi. In order to connect the OnReal camera to your smartphone, all you need to do is download the Fondi OnReal app from either the Apple App Store or Google Play, install the app, connect to a wireless network called "OnReal", enter the password to connect and you are good to go. Highlights • Built-in Wi-Fi • 120∘ Wide Viewing Angle • Battery: 400mAh Lithium-ion Rechargeable Battery • Battery Life: 1 Hour (Wi-Fi Mode Off) • Video Quality: 1080P, 30FPS • Photo Capture: 8 Mega Pixels • Time Lapse at 1/5/10/30/60 Second Intervals • Compatibility: Android 4.0 and Above and iOS 7.0 and Above • Class 10 Micro SD Card Slot up to 32 GB (Sold Separately) • Accessories: Magnet, Clip, Suction Pad and Adhesive Mount, • Velvet Pouch • USB Cable • Compatibility: Android 4.0 and Above and iOS 7.0 and Above Please Note The Fondi OnReal Cam does not have any Internal memory, a MicroSD Flash memory card with Class 10 with size up to 32GB must be purchased separately to operate this device

Fondi OnReal Camera - 8MP Photo Capture, 1080P 30FPS Full HD Video Quality, Built-in Wi-Fi, 120 degree Wide Viewing Angle, 400mAh Lithium-ion Rechargeable Battery, Compatible with Android 4.0 and above and iOS 7.0 and Above -Black, Retail Box, 1 year Limited Warranty Product Overview The Fondi OnReal Cam is a fun and entertainment digital fashion technology gadget which is essentially a wearable camera, similar to the GoPro or the HTC ReCamera, which allows you to capture and share real time videos and photos onto various social media platforms and features a smooth surface and weighs less than 25 grams. In terms of specifications, the device comes with the capability of recording Full HD videos at a resolution of 1080 pixels, through its 8-megapixel CMOS sensor. Users can add up to 32GB of memory to the device through the microSD card slot. With its unique shape, design this unit is currently available in Black or White colour options in South Africa. The OnReal Cam also comes with accessories such as magnet, adhesive mount, suction cup and clip, inside the box, so if you are looking for a compact device that can shoot your road trips or your extreme sports adventures, but are on a budget, the Fondi OnReal Cam could do the trick. Please Note The Fondi OnReal Cam is compatible with both Android and iOS devices and it connects to smartphones and tablets through Wi-Fi. In order to connect the OnReal camera to your smartphone, all you need to do is download the Fondi OnReal app from either the Apple App Store or Google Play, install the app, connect to a wireless network called "OnReal", enter the password to connect and you are good to go. Highlights • Built-in Wi-Fi • 120∘ Wide Viewing Angle • Battery: 400mAh Lithium-ion Rechargeable Battery • Battery Life: 1 Hour (Wi-Fi Mode Off) • Video Quality: 1080P, 30FPS • Photo Capture: 8 Mega Pixels • Time Lapse at 1/5/10/30/60 Second Intervals • Compatibility: Android 4.0 and Above and iOS 7.0 and Above • Class 10 Micro SD Card Slot up to 32 GB (Sold Separately) • Accessories: Magnet, Clip, Suction Pad and Adhesive Mount, • Velvet Pouch • USB Cable • Compatibility: Android 4.0 and Above and iOS 7.0 and Above Please Note The Fondi OnReal Cam does not have any Internal memory, a MicroSD Flash memory card with Class 10 with size up to 32GB must be purchased separately to operate this device.(003)

GSM/GPRS Shield Expansion Board EFCom Wireless Module With Antenna Description: The GPRS Shield-EFCom expansion board is a serial GSM / GPRS wireless module. Arduino enthusiasts to quickly learn a GSM / GPRS mobile phone development, and can be applied to wireless development projects to the class, but also suitable for remote control development, such as wireless meter reading, smart appliances, ultra-long-range control.   EFCom compatible with all the Freaduino and standards the Arduin development board. EFCom is a 4-band GPRS / GSM module supports four standard band 850/900/1800/1900MHz, send SMS messages, phone calls, faxes, etc. all GPRS handsets have features. EFCom allows your very fast phone development process and the wireless development.   EFCom SIM900 is a patch type GSM / GPRS integrated single-chip, ARM926EJ-S core, build enthusiasts and learn to use the smallest integrated development environment.   The EFCom using AT commands through UART serial configuration settings only need to extend the board into Freaduino board, you will be able to easily control via AT commands EFCom make calls, send text messages... addition EFCom support LCD5110 display (default hair Bluetooth backlight, is inserted in EFCom effect diagram below) and serial keypad keyboard input.   The board set the hardware boot the Button Software boot (D10), hardware RestButton, software Rest (D9) allows use and arduino spiritual and match to meet various types of both hard boot or soft boot or the hard reset or soft restart DIY needs. The two jump take to D0-D3, you are excelent to choose EFCom Arduino communication: software serial port (jumper cap to D2, D3) or hardware serial port (D0, D1).   EFCom three operating modes: Short Message Service SMS service mode Audio music mode GPRS mode Features: Fully compatible the Arduino and Mega2560 development board series Serial communication, the freedom to choose hardware serial port (D0/D1) or software serial communication (D2/D3) and motherboard SIM900, all the IC set aside not only the UART, DEBUG mouth, all GPIO port and KEY PANEL interface Board super capacitor to ensure the RTC work Support both hardware and software switch machines, support for hardware and software restart 4 band 850/900/1800/1900 MHz   Specification: The GPRS Shield power supply 5V GPRS multi-slot class 10/8 GPRS mobile station class B Compliant to GSM phase 2/2 +  - Class 4 (2 W@850/900 MHz)  - Class 1 (1 W@1800/1900MHz) Weight: 3.4g Control via AT commands (GSM 07.07, 07.05 and SIMCOM enhanced AT Commands) SIM application toolkit Supply voltage range: 3.1 - 4.8V Low power consumption: 1.5mA (sleep mode) Operation temperature: -40 ° C to +85 ° C Note: Plug Freaduino / Arduino Main Board, in connection we 9V DC AC adapter. The reason is the need EFCom boot current and maximum peak current 2A, but the USB port is unable to provide such a large current, so must an external power supply equipment.Your SIM card is not lockedBest EFCom communication baud rate of 19200 bps 8-N-1(EFCom default automatic pairing baud rate) Package included: 1 x EFCom wireless module 1 x Quad-Band antenna IO definition: Dimension:   PCB:

 Open box demo test unit. 1 Week old. Highlights  • Built-in Wi-Fi • 120¿ Wide Viewing Angle • Battery: 400mAh Lithium-ion Rechargeable Battery • Battery Life: 1 Hour (Wi-Fi Mode Off) • Video Quality: 1080P, 30FPS • Photo Capture: 8 Mega Pixels • Time Lapse at 1/5/10/30/60 Second Intervals • Compatibility: Android 4.0 and Above and iOS 7.0 and Above • Class 10 Micro SD Card Slot up to 32 GB (Sold Separately) • Accessories: Magnet, Clip, Suction Pad and Adhesive Mount,  • Velvet Pouch • USB Cable • Compatibility: Android 4.0 and Above and iOS 7.0 and Above   Please Note   The Fondi OnReal Cam does not have any Internal memory,  a MicroSD Flash memory card with Class 10 with size up to  32GB must be purchased separately to operate this device.

ASTONVILLA AV05 4/4 Glossy Spruce Wood Acoustic Violin with Accessories Description: Brand: ASTONVILLA Size: 4/4 Face Material: Spruce Wood Back/Side Material: Flame Maple Top/Violin Bridge Material: Maple Wood Tailpiece/Chin Rest/Tuning Peg/End Pin Material: Jujube Wood Violin Bow Material: Brazilwood Shoulder Rest/Fingerboard Materia: Ebony Weight: 52.24oz / 1481g Violin Color: Wood Color Violin Dimensions: (23.42 x 8.27 x 2.76)" / (59.5 x 21 x 7)cm (L x W x H) Bow Length: 29.13" / 74cm Bag Dimensions: (31.5 x 10.43 x 5.12)" / (80 x 26.5 x 13)cm(L x W x H) Size Reference: 4/4 size fits arm length 60cm above the age of 11 years old to adults; 3/4 size fits arm length 56.5-60cm, aged 9-11 years; 1/2 size fits arm length 52-56.5cm, aged 6-10 years; 1/4 size fits arm length 47-52cm, ages 4-7 years old. Features: Suitable for adults 4/4 size and easy to carry Exquisite appearance and fine craftsmanship Convenient to carry, can be played anywhere and anytime Provide the basic accessories for the beginner The tuner also does a great favor to tone tuning The inside of case is very soft to protect the violin Rosin is a free gift for you to apply on the violin bow The shoulder rest prevents the instrument from slipping and offers a comfortable position for playing Perfect violin set for all music lovers, also a good gift for your family or friends Package Includes: 1 x Violin 1 x Bag 1 x Bow 1 x Rosin 1 x Shoulder Rests 1 x String 1 x Tuner Notice: The violin bridge is wrapped by white paper and placed under the tailpiece or inside the violin box. Please check it carefully.

      General Sensor: 1/4 Inch 8 MP CMOS Sensor DSP: AllWinner V3 Image Sensor: IMX179 Screen: 0.96 Inch LTPS LCD Lens: 220 Degree fish-eye lens, f=1.1mm, F2.0 Lens Angle: 360 + 220 Degrees Image Format: JPG Video Format: MP4 Decode Format: H.264 Frame Rate: 60fps Photos Resolution: 16M (4096x4096), 12M (3264x3264), 8M (2880x2880), 5M (2448x2448) Video Resolution: 2448P (2448x2448) 30fps, 2048P (2048x2048) 30fps, 1440P (1440x1440) 30/60fps, 1072P (1072x1072) 30/60fps Mode: Round, 360° panoramic, Half-half, Half round, Inner rim, Aunnular, Square, VR Loop recording: Off, 2min, 3min, 5min Slow motion: yes, 1440P (1440x1440) 60fps Time lapse: Off, 0.5s, 1s, 2s, 5s, 10s, 30s, 60s Timed: Off, 3s, 5s, 10s, 20s Auto: Off, 3s, 5s, 15s, 20s, 30s Burst mode: 3, 5,10 Photo Per Second Exposure: -3, -2, -1, 0, +1, +2, +3.0 White Balance: Auto, Sunny, Cloudy, Incandescent light, Fluorescent Driving Mode Light Source Frequency: Auto, 50Hz, 60Hz Built in MIC and Speaker WIFI Distance: up to 10 Meters WIFI: IEEE 802.11 b/g/n WIFI Function: Remote Control, Sync and Sharing Albums APP: Support iOS 9.1, Android 4.1 and above APP name: XDV360 Operation System: Windows XP/7/8/Vista and Mac 10.5 or above Battery: 1200mAh Li-­polymer Battery (Removable) Charging Time: Up to 1.5 Hours Battery Usage Time: Up to 90 Minutes with WIFI off Memory Type: Micro SD Card, Up to 64GB (not included) Class Rating Requirements: Class 6 or Above Waterproof Rating: IP68 (with waterproof case), 30m underwater Other Operating Temperature: ­-10 to 55 Degree Celsius Storage Temperature: ­-20 to 70 Degree Celsius Support Working as PC Camera Ports Micro USB Micro HDMI Micro SD Card Language English, Japanese, Korean, Russian, Deutsch, French, Italian, Spanish, Polish, Dutch, Portuguese, Thai, Simplified Chinese, Traditional Chinese Dimensions Main Product Dimensions: 55x 64 x73 mm (L x W x D) Main Product Weight: 88g