Charging module

10Pcs Mini 1A Lithium Battery Charging Module Board With USB Interface Description: Charging method: linear charge 1% Charging current: 1A adjustable Charge accuracy: 1.5% Input voltage: 4.5V-5.5V Full charge voltage: 4.2V Charging indicator: Red charging green full charge Charging input interface: Mini USB Working temperature: -10C to +85C Reverse: NO Size: 25 x 19 x 10mm Note: Ampere meter can only be connected to 5V input end of the module. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough. The connection wire should not be too long. Make sure the connect point is good. If the input voltage is too high, like 5.2V, the current will be less than 1000mA, it is normal. It is protection function, Auto-substract the charging current to avoid burn damage to chip. Input reverse has no effect on the chip, but the output (battery terminals) reverse will burn chips. Applications: This module is used for single-or multi-section parallel lithium lithium rechargeable battery, charging from the USB port to take power. Package included: 10 x 1A lithium battery charging module

Watch Magnetic Charging Module with USB Connector Portable Compact Cable Free Design for Use with Laptops, USB Wall Chargers Power Banks and more Combines MagSafe technology with inductive charging. The Magnetic Charging Module is compatible with Apple Watch Series 4, Series 3, Series 2, Series 1 and (1st generation) Size: 38mm (Diameter) | 13mm (Height) | 53mm (Wide -Including USB Connector) A portable tangle free solution without the hassle of wires. Simply plug into a USB port on your laptop, charger or portable power bank to charge your Watch. - Combines MagSafe technology with inductive charging. The Magnetic Charging Module works with Watch Series 3, Watch Series 2, Watch Series 1 and Watch (1st generation).

Description: 5A Constant LED Driver Battery Charging Module Voltmeter Ammeter Adjustable step-down module Specifications: Module Properties: non-isolated constant current and voltage module Rectification: non-synchronous rectification Conversion efficiency: 95% (the highest) Switching frequency: 300KHz Output ripple: 50mV (max) 20M bandwidth Load Regulation: ± 0.5% Voltage Regulation: ± 2.5% Operating Temperature: -40?ﾃto +85??br />Voltmeter Ammeter Measurement accuracy: 0.1% Refresh rate: about 200ms / times Display: 0.28"digital tube Current Range: 0A-5A Voltage range: 5V-30V Please connect right as the printed:"IN-,IN+,OUT-, OUT+", or the Module will be burned. Package included: 1 x Constant Current/Voltage Battery Charging Module Details pictures:

Buy XH-M601 12V Battery Charging Module Smart Charger Automatic Charging Power Outage Power Control Boar for R93.90

Buy 10PCS Lithium Battery Charging Module Set 5V 1A TP4056 Charging Modules + 5V 2A for R195.24

Buy XH-M601 12V Battery Charging Module Smart Charger Automatic Charging Power Outa for R195.24

Buy 3.7V Lithium Battery Solar Controller USB Charging Module Board for R194.90

Buy 3pcs 5V 1A Wireless Power Supply Charging Module 5W Wireless Charger Transmitte for R279.00

Buy 3pcs 5V 1A Wireless Power Supply Charging Module 5W Wireless Charger Transmitter Quick Charger DIY M for R284.00

Buy DC10-30V to DC5V 12A Car Power Charging Module with Shell Power Supply Board for R728.61

Buy DC10-30V to DC5V 12A Car Power Charging Module with Shell Power Supply Board for R784.50

Buy 5V 1A Wireless Power Supply Charging Module 5W Wireless Charger Transmitter Quick Charger DIY Micro for R205.00

Buy 6pcs for Tp4056 Charging Module with Battery Protection 18650 Bms 5v for R140.00

Please refer to our website for current and up to date pricing www.lantis.co.za Courier options available for online orders TP4056 5V 1A Lithium Battery Charging Module The TP4056 is a complete constant current / constant voltage linear charger for single cell lithium ion batteries. It's SOP package and low external component count make the TP4056 ideally suited for portable applications. The TP4056 includes current monitor, under voltage lockout, automatic recharge and two status pin to indicat charge termination and the presence of an input voltage. Features: Programmable charge current up to 1000mA No Mosfet, sense resistor or blocking diode required Complete linear charger in SOP-8 package for single cell lithium ion batteries Constant current / constant voltage Charges single cell Lithium Ion batteries directly from USB port Preset 4.2V charge voltage with 1.5% accuracy Automatic recharge

Buy Charging Control Module Storage Lithium Battery Charger-DC 12-24V for R299.00

30Pcs Mini 1A Lithium Battery Charging Board Charger Module USB Interface Description: Charging method: linear charge 1% Charging current: 1A adjustable Charge accuracy: 1.5% Input voltage: 4.5V-5.5V Full charge voltage: 4.2V Charging indicator: Red charging green full charge Charging input interface: Mini USB Working temperature: -10°C to +85°C Reverse: NO Size: 25 x 19 x 10mm Note: Ampere meter can only be connected to 5V input end of the module. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough. The connection wire should not be too long. Make sure the connect point is good. If the input voltage is too high, like 5.2V, the current will be less than 1000mA, it is normal. It is protection function, Auto-substract the charging current to avoid burn damage to chip. Input reverse has no effect on the chip, but the output (battery terminals) reverse will burn chips. Applications: This module is used for single-or multi-section parallel lithium lithium rechargeable battery, charging from the USB port to take power. Package included: 30 x 1A lithium battery charging module

Buy 3pcs 7S NiMH NiCd Rechargeable Battery Charger Charging Module Board Input DC 5V for R215.08

Buy 5pcs 2S NiMH NiCd Rechargeable Battery Charger Charging Module Board Input DC 5V for R320.37

Buy 3pcs 5S NiMH NiCd Rechargeable Battery Charger Charging Module Board Input DC 5V for R331.00

Buy 10pcs 3S NiMH NiCd Rechargeable Battery Charger Charging Module Board Input DC 5V for R607.00

Module parameters: Input voltage: 6V-32V Output voltage: 1.5-32V continuously adjustable (can only be used step-down module, the input must be greater than the output 1.5V or more) Output current: adjustable, the maximum 5A (recommended in the use of 4.5A, when exceed 3A or 35W the best to strengthen the cooling! Suggest using a small fan at the input terminal! Constant current requires an output voltage of 2V or more to be adjusted, the current regulation, only in the constant current state will work, constant current is mainly directly used to the low resistance battery charge or LED working current limit and other use, please make sure about this before you order it. Output power: up to 75W (recommended in the use of 50W, if uses large pressure difference, please reduce the power) Operating temperature: -20 to +70 degrees (pay attention to the power tube temperature, when exceed please strengthen the cooling) Operating frequency: 180KHz Conversion efficiency: up to 96% Short circuit protection: Yes, constant current Current set constant current value Over-temperature protection: Yes (over-temperature automatically turn off the output) Input reverse protection: Yes Output reverse flow: None, for charging please add a diode! Installation: 8pcs pillars, 8pcs 3mm screws Wiring method: wiring terminal or soldering terminal, VIN for the input, VOUT for the output Module size: 65.6mm x 40mm x 25mm (L*W*H) Weight: 77g Calibration method: The module has a calibration function, don't worry about measuring inaccurate problems, if you find the measurment is not inaccurate you can use the following methods calibration. Just need to calibration once for the first time! Voltage calibration: In the case of power down, press and hold the "SET" button, power on, enter the voltage calibration mode, the LCD screen starts to flash, release the set button, press the "Set" key to add, "OK" to reduce, calibrate correct input voltage, such as: the input voltage is 12.65V, then adjust the current voltage to 12.65V, after 2 seconds it automatic save, power off and exit to complete the calibration! Current calibration: For no-load current display, or current is too large! In the case of power off, press and hold the "OK" button, power on, enter the current calibration mode, the LCD screen starts to flash, release the "OK" button, press the "Set" button to add, "OK" button to reduce, calibrate correct current, such as: no load display 0.02A, then adjust to 0.00A, after 2 seconds it automatic save, power off and exit to complete the calibration! Special Note: Some customers feedback that the output voltage can not be adjusted, this is due to the factory default voltage is 20V. When you encounter this problem, please counterclockwise rotation ADJ-V potentiometer 10 laps above, until the voltage value changes, and then the module can be normal adjustment of the voltage. Note: USB output voltage and the module output voltage needs to be consistent, when the USB indicator does not light, means USB has no output, when the USB light is set, it is not fixed 5V output, when charging USB device please make sure the voltage is 5V, if higher than 5.5V screen will flash, it will be reminded to adjust the voltage, otherwise it may damage your device, USB output power is turned off by default, to ensure that mistakenly plug USB will not damage the device. Setting Description: Setting key can be set to four kinds of display mode: 1. F-0 mode: display output voltage; 2. F-1 mode: display input voltage; 3. F-2 mode: alternately display input and output voltage; 4. USB mode: display USB output voltage and turn on or off the USB output; Instructions: press the "set" button, the cycle shows four kinds of display mode, the corresponding indicator light will on/off, press the "OK" key to save and exit, press the "OK" button to switch the LCD backlight. Package includes: 1 x 5A DC-DC Adjustable Step Down Power Supply Module (Board color will send in random)

LED Driver Charging Constant Current Voltage Step Down Buck Module Feature: This module uses the LM2596 chip, high efficiency (up to 92%), low heat, can be very easily used to above 3A current, in conjunction with the original TI op amp control output current, so the overall output is very stable. This module uses the original Sanyo low ESR filter capacitor, you can make low ripple voltage to 50mV! This module uses machine placement, reflow soldering. This module is an adjustable buck module, the module can be adjusted from the blue adjustable resistor to change the output voltage. Input and output differential pressure is 2V, the minimum can be output 1.23V. Module indicated IN - (negative input), IN + (positive input), OUT - (negative output), OUT + (positive output), please note must be correct connected, otherwise may cause damage to the module. Description: Nature of the module: Non-isolated step-down module Rectification: Non-synchronous rectification Input voltage: 7V - 35V Output voltage: 1.25V - 30V Output current: Adjustable, 3A (maximum) Transfer efficiency: 92% (maximum) Switching frequency: 150KHz output ripple: 50mV (maximum) 20M Kbps Load regulation: ±0.5% Voltage regulation: ±2.5% Operating temperature: -40°C to +85°C Dimension: 48 x 23 x 14mm (L x W x H) Battery charging method: 1. Make sure the battery float voltage and charging current, the module input voltage; 2. Adjustment constant potentiometer, the output voltage is adjusted to about 5V. 3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjust the constant current potentiometer make the output current reaches a predetermined charge current value; 4. Turn lamp current default is 0.1 times charging current (constant current value), if you need to adjust please adjust the turn lamp current potentiometer; (generally doesn't need adjustment) 5. Adjustment constant potentiometer allows the output voltage reaches the float voltage; 6. Connected to the battery and try to charge. (1,2,3,4,5 steps are for the module input connected to the power supply, output-load battery is not connected.) LED constant current driver using method: 1. Make sure that the drive LED operating current and maximum working voltage; 2. Adjustment constant potentiometer, output voltage adjusted to about 5V. 3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjusting the constant current potentiometer allows the output current reaches a predetermined LED working current; 4. Adjustment constant potentiometer allows the output voltage reaches the maximum operating voltage LED; 5. Connect LED, test machine. (1,2,3,4 steps are module input connect to the power supply, output-load is not connected LED lights.) Package included: 1 x Buck module

Specifications: · 300W 8A 7-32V to 0.8-28V DC CC CV Buck Step-Down Converter Power Supply Step Down Module Adjustable Voltage Regulator LED Driver · High-power, constant current LED driver · Battery charger · Vehicle-mounted power supply · Low voltage system power supply · Non-isolated step-down CC CV Buck module with on-board LED load indicator · Input voltage: DC 7-32 V · Output Voltage: DC 0.8-28 V (Adjustable) · Output Current: 8A (MAX), more than 60Deg please strengthen heatsink · Continuous Current Range: 0.2-8A Adjustable · Output Power: 300W (MAX) · Conversion efficiency: 95% (more input voltage, more efficiency) · Output ripple: 50mV · Working Temperature: industrial (- 40 ° c to +85 °c) (environmental temperature, more than 40 degrees, please reduce power to use, or - enhance cooling) · No-load current: 20mA (input 24V,Output 12V for reference) · Voltage regulation: ± 1% · Load regulation: ± 1% · Dynamic response speed: 200uS 5% · Short circuit protection: YES · Input Reverse protection: No (please comply with a reverse protection or connect a diode at input parts.) · Size: 65 x 47 x 22 mm · On-board LED load indications: red = load present (eg. 'battery charging'), green = no load (eg. 'battery charged' or output disconnected) Features: 1. Fixed turn lamp current is 0.1 times the current value(Used to identify whether the battery is fully charged When charging). 2. Made from a dedicated benchmark IC and high-precision current sensing resistor, proving a more stable constant current, (when 20°C to 100°C constant current 1A, temperature drift less than 1%). Particularly suitable for LED driver. 3. High output current, the max output current can reach 8A. 4. Four high frequency capacitance, can lower output ripple, enhance the work stabilization. 5. Double heat sink design. MOS schottky diode independent heat sink,which heat dissipation is good, and won't affect each other. 6. Using large size Sendust Core and double pure copper wiring, improve working efficiency, reduce fever. 7. 3296 multiturn potentiometer,high accuracy voltage and current regulation, good stability. 8. Double color lamp, working condition be clear at a glance 9. Voltage and current are adjustable,wich effect is good. Applications: 1. High-power LED driver. 2. Lithium battery(or lead accumulator) charge. 3. Vehicle-mounted power supply. 4. Low voltage system power supply. 5. 6V, 12V, 14V, 24V battery charge. 6. On-board laptop power supply. 7. regulated power supply. 8.Low voltage power supply system. Module adjustment: ￢ﾀﾋ 1. When the module output voltage can not be adjusted (the output voltage is always equal to the input voltage) Please adjust the potentiometer counterclockwise 20 laps (20 turns) or more till it works.￢ﾀﾋ 2. Turn trimmers CLOCKWISE to INCREASE, ANTICLOCKWISE to DECREASE. 3. When adjust the blue potentiometer,please use a multimeter to monitor the voltage 4. The trimmer nearest the voltage output adjusts the output CURRENT (CC) 5. The trimmer nearest the voltage input adjusts the output VOLTAGE (CV) Charger application - intructions: 1. First determine the float voltage and charging current required by the battery to be charged (the ‘target battery'). The target battery disconnected from the module output, apply a voltage of 7V - 32V to the module input, being sure to observe correct polarity. 2. Using the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the charging current required by target battery. 4. Using the CV trimmer, adjust the module's output voltage to the float voltage required by the target battery. 5. Connect the target battery to the module output, observing correct polarity. Charging of the battery should commence ￢ﾀﾋ Constant current LED Driver Application - Instructions: 1. First determine the operating current and maximum operating voltage of the LED you need to drive. 2. With the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the operating current of your LED. 4. Adjust the CV trimmer to make the output voltage reach the maximum LED operating voltage. 5. Connect LED, test. Package included: 3 x 8A 300W buck adjustable power supply module

Specifications: · 300W 8A 7-32V to 0.8-28V DC CC CV Buck Step-Down Converter Power Supply Step Down Module Adjustable Voltage Regulator LED Driver · High-power, constant current LED driver · Battery charger · Vehicle-mounted power supply · Low voltage system power supply · Non-isolated step-down CC CV Buck module with on-board LED load indicator · Input voltage: DC 7-32 V · Output Voltage: DC 0.8-28 V (Adjustable) · Output Current: 8A (MAX), more than 60Deg please strengthen heatsink · Continuous Current Range: 0.2-8A Adjustable · Output Power: 300W (MAX) · Conversion efficiency: 95% (more input voltage, more efficiency) · Output ripple: 50mV · Working Temperature: industrial (- 40 ° c to +85 °c) (environmental temperature, more than 40 degrees, please reduce power to use, or - enhance cooling) · No-load current: 20mA (input 24V,Output 12V for reference) · Voltage regulation: ± 1% · Load regulation: ± 1% · Dynamic response speed: 200uS 5% · Short circuit protection: YES · Input Reverse protection: No (please comply with a reverse protection or connect a diode at input parts.) · Size: 65 x 47 x 22 mm · On-board LED load indications: red = load present (eg. 'battery charging'), green = no load (eg. 'battery charged' or output disconnected) Features: 1. Fixed turn lamp current is 0.1 times the current value(Used to identify whether the battery is fully charged When charging). 2. Made from a dedicated benchmark IC and high-precision current sensing resistor, proving a more stable constant current, (when 20°C to 100°C constant current 1A, temperature drift less than 1%). Particularly suitable for LED driver. 3. High output current, the max output current can reach 8A. 4. Four high frequency capacitance, can lower output ripple, enhance the work stabilization. 5. Double heat sink design. MOS schottky diode independent heat sink,which heat dissipation is good, and won't affect each other. 6. Using large size Sendust Core and double pure copper wiring, improve working efficiency, reduce fever. 7. 3296 multiturn potentiometer,high accuracy voltage and current regulation, good stability. 8. Double color lamp, working condition be clear at a glance 9. Voltage and current are adjustable,wich effect is good. Applications: 1. High-power LED driver. 2. Lithium battery(or lead accumulator) charge. 3. Vehicle-mounted power supply. 4. Low voltage system power supply. 5. 6V, 12V, 14V, 24V battery charge. 6. On-board laptop power supply. 7. regulated power supply. 8.Low voltage power supply system. Module adjustment: ￢ﾀﾋ 1. When the module output voltage can not be adjusted (the output voltage is always equal to the input voltage) Please adjust the potentiometer counterclockwise 20 laps (20 turns) or more till it works.￢ﾀﾋ 2. Turn trimmers CLOCKWISE to INCREASE, ANTICLOCKWISE to DECREASE. 3. When adjust the blue potentiometer,please use a multimeter to monitor the voltage 4. The trimmer nearest the voltage output adjusts the output CURRENT (CC) 5. The trimmer nearest the voltage input adjusts the output VOLTAGE (CV) Charger application - intructions: 1. First determine the float voltage and charging current required by the battery to be charged (the ‘target battery'). The target battery disconnected from the module output, apply a voltage of 7V - 32V to the module input, being sure to observe correct polarity. 2. Using the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the charging current required by target battery. 4. Using the CV trimmer, adjust the module's output voltage to the float voltage required by the target battery. 5. Connect the target battery to the module output, observing correct polarity. Charging of the battery should commence ￢ﾀﾋ Constant current LED Driver Application - Instructions: 1. First determine the operating current and maximum operating voltage of the LED you need to drive. 2. With the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the operating current of your LED. 4. Adjust the CV trimmer to make the output voltage reach the maximum LED operating voltage. 5. Connect LED, test. Package included: 5 x 8A 300W buck adjustable power supply module

Specifications: · 300W 8A 7-32V to 0.8-28V DC CC CV Buck Step-Down Converter Power Supply Step Down Module Adjustable Voltage Regulator LED Driver · High-power, constant current LED driver · Battery charger · Vehicle-mounted power supply · Low voltage system power supply · Non-isolated step-down CC CV Buck module with on-board LED load indicator · Input voltage: DC 7-32 V · Output Voltage: DC 0.8-28 V (Adjustable) · Output Current: 8A (MAX), more than 60Deg please strengthen heatsink · Continuous Current Range: 0.2-8A Adjustable · Output Power: 300W (MAX) · Conversion efficiency: 95% (more input voltage, more efficiency) · Output ripple: 50mV · Working Temperature: industrial (- 40 ° c to +85 °c) (environmental temperature, more than 40 degrees, please reduce power to use, or - enhance cooling) · No-load current: 20mA (input 24V,Output 12V for reference) · Voltage regulation: ± 1% · Load regulation: ± 1% · Dynamic response speed: 200uS 5% · Short circuit protection: YES · Input Reverse protection: No (please comply with a reverse protection or connect a diode at input parts.) · Size: 65 x 47 x 22 mm · On-board LED load indications: red = load present (eg. 'battery charging'), green = no load (eg. 'battery charged' or output disconnected) Features: 1. Fixed turn lamp current is 0.1 times the current value(Used to identify whether the battery is fully charged When charging). 2. Made from a dedicated benchmark IC and high-precision current sensing resistor, proving a more stable constant current, (when 20°C to 100°C constant current 1A, temperature drift less than 1%). Particularly suitable for LED driver. 3. High output current, the max output current can reach 8A. 4. Four high frequency capacitance, can lower output ripple, enhance the work stabilization. 5. Double heat sink design. MOS schottky diode independent heat sink,which heat dissipation is good, and won't affect each other. 6. Using large size Sendust Core and double pure copper wiring, improve working efficiency, reduce fever. 7. 3296 multiturn potentiometer,high accuracy voltage and current regulation, good stability. 8. Double color lamp, working condition be clear at a glance 9. Voltage and current are adjustable,wich effect is good. Applications: 1. High-power LED driver. 2. Lithium battery(or lead accumulator) charge. 3. Vehicle-mounted power supply. 4. Low voltage system power supply. 5. 6V, 12V, 14V, 24V battery charge. 6. On-board laptop power supply. 7. regulated power supply. 8.Low voltage power supply system. Module adjustment: ??br /> 1. When the module output voltage can not be adjusted (the output voltage is always equal to the input voltage) Please adjust the potentiometer counterclockwise 20 laps (20 turns) or more till it works.??br />2. Turn trimmers CLOCKWISE to INCREASE, ANTICLOCKWISE to DECREASE. 3. When adjust the blue potentiometer,please use a multimeter to monitor the voltage 4. The trimmer nearest the voltage output adjusts the output CURRENT (CC) 5. The trimmer nearest the voltage input adjusts the output VOLTAGE (CV) Charger application - intructions: 1. First determine the float voltage and charging current required by the battery to be charged (the ‘target battery'). The target battery disconnected from the module output, apply a voltage of 7V - 32V to the module input, being sure to observe correct polarity. 2. Using the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the charging current required by target battery. 4. Using the CV trimmer, adjust the module's output voltage to the float voltage required by the target battery. 5. Connect the target battery to the module output, observing correct polarity. Charging of the battery should commence ??br /> Constant current LED Driver Application - Instructions: 1. First determine the operating current and maximum operating voltage of the LED you need to drive. 2. With the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the operating current of your LED. 4. Adjust the CV trimmer to make the output voltage reach the maximum LED operating voltage. 5. Connect LED, test. Package included: 3 x 8A 300W buck adjustable power supply module

3.7V Li-ion Battery Mini USB To USB A Power Supply Module 5V 1A Charger Module Features: This PCB also support charging the battery, simply supply a 5V micro USB source to the charging input and it will charge the connected battery to 4.2V. Great for mobile power source using Lithium ion batteries (unprotected is also ok). Connect multiple batteries to the battery input to increase the capacity power capacity. With iphone recognition circuit, can charge iPhone. Protection Circuit: Overcharge protection: 4.3V Overcharge protection release: 4.1V Overdischarge protection: 2.9V Overdischarge protection release: 3V Specification: Charging voltage input: 5V 1A Step up voltage output: 5V 1A max Transient current: 180uA Red LED: Charging Green LED: Charging completed Blue LED: There is a load in the USB Size: 50 x 20 x 9 mm Package include: 1 x USB DC 5V power supply

Description: This product is for the current wireless charging various series of small electronic products, and power development and design is made with a small size, extremely easy to use, high efficiency, low cost features primarily for mobile electronics products such as: cell phones, game machine, fish tank, MP3, MP4, adult products, digital cameras, electric shavers, machine learning, medical supplies and other products of underwater applications; As a result of non-contact charging power supply, make the product completely sealed, waterproof and dustproof, increase the life of the product and easier to use. Module main parameters: Input voltage: 9 -12V Maximum load current: 1.1A The max output voltage and current of receive: 5V / 2A, 12V / 700mA Transmitting coil size: diameter 43mm, thickness 2.3mm Transmitter module size: 18mmx8.5mmx15mm Receiving coil size: diameter 43mm, thickness 1.2mm Receiver Module size: 10mmx25mmx3mm Receive the best distance: 3 - 6mm Package included: 1 x Transmitter 1 x Receiver

Description: 1080P Wireless Remote Control Module Board Mini Camera DV DVR Recorder with Microphone Hidden HD Camcorder   Features: Mini camera uses 2.4G wireless remote control, remote control distance of up to 20 meters, including the curve reflects the simple, responsive. Using high-capacity battery, continuous recording up to 5 hours of recording time without the human body sensor. Use CCD lenses to ensure high-resolution, low light. It is only used for forensic purposes of public security, court reporters, lawyers, etc. Prohibited for illegal videotaping, such as for illegal videotaping constitutes a crime, our Company is out of responsibility.   Specification: Video format: AVI Video encoding: M-JPEG Video resolution: 1280 x 960 Photo: 1280 x 1024 Video frame rate: 30fps Picture format: JPG Image ratio: 4:3 Playback software: Operating system or Mainstream audio and video playback software Support System: Windows 2000/XP/2003/Vista; Macos; Linux Working time: About 25 hours Charging voltage: DC-5V Battery Type: High capacity polymer lithium battery 3000mah Interface type: Mini 8Pin USB Storage: TF card Operating Instructions: 1. Starting up: slide the switch on the machine  to ON, press the A button on the remote control, red keep bright enters the standby state 2. Take photo: In standby mode, short press the B button, and red lights flashing once, it means take a picture and save it. 3. Take video: In standby mode, short press the C key, red light flashing three times then off, then starting to take video, then press the C button, the red bright, stop recording and save. 4. Body sensor camera: In standby mode, short press the D button, the red and blue light flash three times, then enter the motion detection status. When detect a moving picture object, blue lights flash again, then start recording. 5. Shutdown: In standby mode, press the A button, blue light flashes three times, shut down. (slide switch to the off, cut off all power) 6. USB connected to the computer: open the removable disk can read the file, USB connected to the computer 7. Charging: USB connected to the computer ro charging,Or you can connect the charger, the red light flashes when charging, fully charged red keep bright.. 8. Time modify setting: Please insert the TF card to the machine, connect the computer, open the "Time" document in the removable hard disk, then change the time to current time, then save the “Time” file. After saving the file and exit security hardware, restart the machine, time setting is completed. And now video file time of watermark is set at the same time with you.   Package includeds: 1 x Module Camera 1 x USB Cable 1 x Remote Control 1 x User Manual   Details pictures:

Description: This develop board integrated ESP8266 and 18650 battery. A standard 3000mAH 18650 battery could run it 17 hours. What is it? You can call it "WiFi Battery". I added a 18650 battery to ESP8266 make ESP8266 more easy to develop projects. Why did you make it? When you do some ESP8266 projects you must hate to add a power bank to provide the power. This tiny board could solve such problems. A 3000mAH 18650 battery could make ESP8266 run 17 hours or more. What makes it special? · Same with NodeMCU. · 18650 charging system integrated. · indicate LED inside(Green means full& Red means charging) · Charging and working could be at the same time. · 1 Switch could control the power. · 1 SMT connector could be used to sleep mode · 1 extra LED could be programmed(Connected with GPIO16[D0]) · 0.5A charging current · 1A output · Over charge protection · Over discharge protection · 10 digital pins write/read/interrupt/pwm/I2C/one-wire supported(except D0) · 1 analog input Be careful + and -. If you put the wrong direction of battery the charging chip will be destroyed. This product does not include 18650 battery. Dimensional drawing: this size is measured by hand,There may be 1-3mm errors. Package included: 1 x WeMos® esp-wroom-02 Mainboard D1 Mini WIFI Module

Characteristic: On-board TP4056 lithium battery charging management chip On-board micro USB head, can be directly connected with most of the smart phone charger as the input side to the lithium battery charging Reserved IN+ and IN- input port, convenient user DIY On-board charging status indicator Support charge discharge over current protection Chip with constant current and constant pressure, full automatic stop Supports simultaneous charging and discharging Parameter: Input voltage: DC5V Charge cutoff voltage: DC4.2V±1% Charge maximum output current: 1.2A Charging mode: linear charge Working environment temperature: -20-85 degrees Celsius Package included: 5 x Micro USB TP4056 Charge And Discharge Protection Module