Card shield

Description: Now, you can drive TFT LCD in a much faster speed using 84Mhz Ardiuno DUE. The shield is designed to fit two types of LCD: 1. 40pin version LCD which is commonly used in previous version of TFT Mega shield for Arduino MEGA 2560 2. 32pin version LCD which is commonly used in STM32 development board. (unsoldered) The shield route all the LCD data pins to port PC1-PC8 and PC12-19, control pins to PD0-PD3, this design can acheive high speed data transfer (three cycles per write strobe to the LCD) to maximize LCD display speed. The SPI interface (for SD or flash control) is route to the ISP header of arduino DUE, so that high speed SPI transfer with DMA can be achieved. The shield is compatible with Arduino DUE and the following LCD: 2.2" TFT LCD Module  (220x176) 2.8" TFT LCD Module  (320x240) 3.2" TFT LCD Module with Font IC (320x240) 3.2" High Resolution TFT LCD Module with Font IC (480x320) 3.5" TFT LCD Module with Font IC (480x320) (Full viewing angle IPS panel) 4.0" TFT LCD Module with Font IC (480x320) 4.3" TFT LCD Module with Font IC (480x272) 5.0" TFT LCD Module with Font IC (800x480) 7.0" TFT LCD Module with Font IC (800x480) Features: - Drive TFT LCD on arduino DUE by just plugging into arduino DUE main board, no flying wires - Compatible with 40-pin version LCD, which is commonly used in TFT Mega shield - Also comptabile with 32-pin version LCD, which is commonly used in STM32 development board - On board SD card slot with adjustable CS selection - On board SPI flash footprint with adjustable CS selection, for upgrade include Font IC to draw text to the LCD and also support SPIFlash library - LCD power 3.3V and 5V selectable through solder jumpers - LCD Backlight (LEDA+) 3.3V., 5V or PWM selectable through solder jumpers - Pins are routed to reduce CPU cycles, i.e. display speed is faster Package included: 1 x CTE TFT LCD / SD Card Shield For Arduino DUE

Buy CTE TFT LCD / SD OLED Card Shield For DUE Support 32Pin 40Pin Version LCD for R425.09

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA More informations: https://myosuploads3./products/20181029/20181029050819SKU122168.rar Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: It is a self-drilling card holder for easy insertion and removal of the card. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 1 x Micro SD TF card module Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter For Arduino Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter For Arduino Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter For Arduino

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Features Can play a variety of music formats, support for OGG encoding real-time recording SPI interface, the control signal lines are led out A headphone and stereo output A microphone for recording A line_in input interface Power indicator 3.3V and 2.8V of LDO chip AMS-1117 on board, provides up to 800mA current A single power supply: +5 VDC 12.288 MHz crystal TF card slot Package included: 1 x MP3 Music VS1053B Shield Board With TF Card Slot MP3 Music VS1053B Shield Board With TF Card Slot Work With Arduino UNO MEGA MP3 Music VS1053B Shield Board With TF Card Slot Work With Arduino UNO MEGA MP3 Music VS1053B Shield Board With TF Card Slot Work With Arduino UNO MEGA

Description: Data logging shield for Arduino NANO a new for Arduino NANO shield,You can get going quickly - saving data to files on any FAT16 or FAT32 formatted SD card, to be read by any plotting, spreadsheet or analysis program. The included Real Time Clock timestamps all your data with the current time, so that you know precisely what happened when! Please note that this item does not come with an for Arduino NANO (you'll need one to use with the shield), or an SD card. SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card Real time clock (RTC) keeps the time going even when the for Arduino is unplugged. The battery backup lasts for years Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering connectors, circuitry or sensors. Onboard 3.3v regulator is both a reliable reference voltage and also reliably runs SD cards that require a lot of power to run Works with for Arduino NANO or MICRO Package Included: 1 x Nano Data Logging Shield For Arduino(Battery not included)

Description VS1053 MP3 Shield The VS1053 is a great MP3 decoder, it is capable of decoding Ogg Vorbis/MP3/AAC/WMA/MIDI audio and encoding IMA ADPCM and user-loadable Ogg Vorbis, can drive 30 ohm headphones with no additional power supply. This VS1053 MP3 Shield is designed based on VS1053B from VLSI. For the best headphone listening experience, the VS1053 includes EarSpeaker spatial processing which accurately simulates how a room with stereo loudspeakers would sound. In addition to being able to decode all major formats, VS1053 is capable of recording in Ogg Vobis files. With the SD card slot on the other side of the board, you can play mp3 files from SD card using this shield. It is easily to drop it in your project or make a mp3 player using your Arduino Quick Spec Can play a variety of music formats, support for OGG encoding real-time recording SPI interface, the control signal lines are led out A headphone and stereo output A microphone for recording A line_in input interface Power indicator 3.3V and 2.8V of LDO chip AMS-1117 on board, provides up to 800mA current A single power supply: +5 VDC 12.288 Mhz crystal SD card slot Audio Sample Listen to an audio sample recorded with a VS1053 using the Wideband Voice profile Resources Mp3 Shield Detailed Introduction VS1053 Datasheet Wiki Shipping List 1 X VS1053 MP3 Shield More Products View More Products

3Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 3 x Micro SD TF card module

10Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 10 x Micro SD TF card module

5Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 5 x Micro SD TF card module

Buy Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter for R210.00

Buy Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter for R182.61

Description: With this Data Log Shield for WiFi D1 Mini board, can saving data to files on any FAT16 or FAT32 formatted MicroSD card. The included RTC (Real Time Clock) can be used to timestamp all your data with the current time, so that you know precisely what happened when. SD card interface works with FAT16 or FAT32 formatted cards. Real time clock (RTC) keeps the time going even when the power disconnected. The coin cell battery backup last date and time. RTC protected from wrong connecting of battery. Pinout: RTC: D1 - SCL D2 - SDA CD card: D5 - CLK D6 - DO D7 - DI D8 - CS Package included: 1 x DataLog Shield 2 x Male Pin Header 2 x Female Pin Header 2 x Stackable Header

Description: With this Data Log Shield for WiFi D1 Mini board, can saving data to files on any FAT16 or FAT32 formatted MicroSD card. The included RTC (Real Time Clock) can be used to timestamp all your data with the current time, so that you know precisely what happened when. SD card interface works with FAT16 or FAT32 formatted cards. Real time clock (RTC) keeps the time going even when the power disconnected. The coin cell battery backup last date and time. RTC protected from wrong connecting of battery. Pinout: RTC: D1 - SCL D2 - SDA CD card: D5 - CLK D6 - DO D7 - DI D8 - CS Package included: 3 x DataLog Shield 6 x Male Pin Header 6 x Female Pin Header 6 x Stackable Header

Description: With this Data Log Shield for WiFi D1 Mini board, can saving data to files on any FAT16 or FAT32 formatted MicroSD card. The included RTC (Real Time Clock) can be used to timestamp all your data with the current time, so that you know precisely what happened when. SD card interface works with FAT16 or FAT32 formatted cards. Real time clock (RTC) keeps the time going even when the power disconnected. The coin cell battery backup last date and time. RTC protected from wrong connecting of battery. Pinout: RTC: D1 - SCL D2 - SDA CD card: D5 - CLK D6 - DO D7 - DI D8 - CS Package included: 5 x DataLog Shield 10 x Male Pin Header 10 x Female Pin Header 10 x Stackable Header

Buy 30pcs Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter for R427.00

3Pcs Logging Recorder Shield Data Logger Module For Arduino UNO SD Card Features: SD card interface works with  FAT16 or FAT32 formatted cards. 3.3V level shifter circuitry prevents damage to your SD card. Real time clock (RTC) keeps the time going even when the Arduino is unplugged. Included libraries and example code for both SD and RTC, means you can get going quickly. Prototyping area for soldering connectors, circuitry or sensors. Onboard 3.3V regulator is both a reliable reference voltage and also reliably runs SD cards that require a lot of power to run. Works with Arduino UNO,  Duemilanove, Diecimila, Leonardo or ADK/Mega R3 or higher. ADK/Mega R2 or lower are not supported. Specification: Size: 68 x 53 x 23mm (approx) Regulator voltage: 3.3V Battery: CR1220 3V Note: This product has red and blue color, the color is random delivery. Package included: 3 x Data logger module 3 x Lithium cell

Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 20 x Micro SD TF card module

Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: It is a self-drilling card holder for easy insertion and removal of the card. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 20 x Micro SD TF card module

10Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Package contains 1 X item of the smallest listed variant.

Buy 2.8 inch TFT LCD Display Shield + UNO R3 Board with TF Card Touch Pen USB Cable Kit For UNO Mega2560 for R565.00

Buy 3Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter for R182.61

Buy GPS SHIELD BOARD W/ SD CARD SLOT AND AERIAL EB0072 / 190019 for R524.50

5Pcs MEGA Sensor Shield V2.0 Expansion Board For Arduino ATMEGA 2560 R3 Description: MEGA Sensor Shield V2.0 Expansion Board For Arduino ATMEGA 2560 R3 1280 ATmega8U2 ATMEL AVR New Arduino MEGA Sensor Shield V2.0 dedicated sensor expansion board set market expansion board advantages in one design, PCB Immersion Gold processed all of the digital and analog interfaces. The motherboard will not only be extended to the steering gear line order form ad hoc Bluetooth modulecommunication interface, SD card module communication interface, APC220 radio frequency module communication interface, and RB URF v1.1 ultrasonic sensor interface, and independent expansion easier to use convenient. Package included: 5 x MEGA sensor shield V2.0 expansion board

Introduction:   1. This shield supports both 16 bit mode. 2. Mega board has enough pins for using SD card and touch function at the same time.Also, the maximum of 2GB is can be supported. 3. The 3.2 TFT LCD module works in 3.3V voltage level and you need to use cables to connect with for Arduino Mega. And this shield can help you out of the bothers to use other cables. You just need to plug the module to Mega through this shield. 4. It has an adjustable button for contrast of the LCD display.   Package included:   1 X TFT   LCD adjustable shield expansion board

Buy 2.8 3.2 Inch TFT/SD Shield Expansion Board For DUE LCD Module SD Card Adapter for R221.97

Buy 2.8 3.2 Inch TFT SD Shield Expansion Board For MEGA 2560 LCD Module SD Card... for R309.00

Buy 2.8 3.2 Inch TFT SD Shield Expansion Board For MEGA 2560 LCD Module SD Card for R326.60

Buy 2.8 3.2 Inch TFT/SD Shield Expansion Board For DUE LCD Module SD Card Adapter Geekcreit for Arduino for R312.00

3Pcs UNO R3 Sensor Shield V5 Expansion Board For Arduino Feature: This Arduino Sensor Shield V5.0 sensor expansion board, the motherboard is not only extended out the Arduino Uno all digits and analog interface to servo line order form, but also add hoc IIC interface, servo controller interface, Bluetooth module communication interface, SD card module communication interface, APC220 radio frequency module communication interface, ultrasonic sensor interface, 12864 LCD serial and parallel interfaces, independent expansion will be more easy and convenient. Package included: 3 x UNO R3 Sensor Shield v5