Board system memory

Description:   Full integration on one board: Uno R3 ATmega 328 and WiFi ESP8266 with memory 32Mb (MegaByte). All of the modules can work together or each separately. And everyone has their own pinout headers. The convenient solution for the development of new projects requiring Uno and WiFi. Via USB you can update sketches and firmvare for ATmega328 and for ESP8266. For this on board have the USB-serial converter CH340G. Use this board is very simple. The board has DIP-switch, to connect the modules. For example, to: USB and ATmega328, USB and ESP8266, ATmega328 and ESP8266. Table DIP- switch: Connection DIP   1 2 3 4 5 6 7 ATmega328 ESP8266 ON ON OFF OFF OFF OFF OFF USB ATmega328 OFF OFF ON ON OFF OFF OFF USB ESP8266 (Update firmware or sketch) OFF OFF OFF OFF ON ON ON USB ESP8266 (communication) OFF OFF OFF OFF ON ON OFF All independent OFF OFF OFF OFF OFF OFF OFF Package included: 1 x UNO+WiFi R3 ATmega328P+ESP8266 Board 32Mb Memory

Buy N76E003AT20 Core Controller Board Development Board System Board for R210.00

Buy 5pcs STM32F030C8T6 Core Board System Board STM32 F0 ARM Development Board... for R399.00

Buy STM32F030C8T6 Core Board System Board STM32 F0 ARM Development Board for R219.00

Buy 3pcs N76E003AT20 Core Controller Board Development Board System Board for R191.10

Buy 10pcs N76E003AT20 Core Controller Board Development Board System Board for R561.76

SYSTEM ON CHIP DEVELOPMENT BOARD RUNS ON DEBIAN; OPENWRT AND ANDROID

Apacer 4GB DDR4 2133Mhz Desktop Memory, Retail Box, Limited 3 Year Warranty Product Overview: Apacer's DDR3 1600 MHz Unbuffered-DIMM module provides higher performance and lower power consumption, making it ideally suited for use in desktops. Apacer's 240-pin DIMMs are used in DDR3 memory for desktop computers. DDR3 is the latest generation of memory with an improved architecture that allows it to transmit data more quickly. A dual inline memory module (DIMM) consists of a number of memory components (usually black) that are attached to a printed circuit board (usually green). The gold pins on the bottom of the DIMM provide a connection between the module and a socket on a larger printed circuit board. The pins on the front and back of a DIMM are not connected to each other. To use DDR3 memory, your system motherboard must have 240-pin DIMM slots and a DDR3-enabled chipset. This is because a DDR3 SDRAM DIMM will not fit into a standard DDR2 DIMM socket or a DDR DIMM socket. Features: • Form Factor UDIMM • Total Capacity 4GB • Warranty Limited Lifetime • Specs: DDR3L PC3L-12800, CL=11, Unbuffered, NON-ECC, DDR3L-1600, 1.35V, 512Meg x 64 • ECC: NON-ECC • Module: Qty 1 • Speed: 1600 MT/S • Tracer: False • Voltage: 1.35V • DIMM Type: Unbuffered • Bullet Features: Increases system performance Specifications: • Stock Code KCP424SS6/4 • Description: Apacer 4GB DDR4 2133Mhz Desktop Memory • DDR3 Speed Grade: 1600Mbps • Unbuffered DIMM: 240-pin • Memory Organization: x8 FBGA DRAM chip • Bandwidth: 12800MB/s • CAS latency (11) • Internal memory - 4 GB • Memory clock speed 1600 MHz • Internal memory type - DDR3 • Component for (PC/server) • Memory layout (modules x size) (1 x 4 GB).(003)

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA More informations: https://myosuploads3./products/20181029/20181029050819SKU122168.rar Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: It is a self-drilling card holder for easy insertion and removal of the card. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 1 x Micro SD TF card module Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter For Arduino Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter For Arduino Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter For Arduino

3Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 3 x Micro SD TF card module

10Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 10 x Micro SD TF card module

5Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 5 x Micro SD TF card module

Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 20 x Micro SD TF card module

Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: It is a self-drilling card holder for easy insertion and removal of the card. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 20 x Micro SD TF card module

Description: Stereo Bluetooth 12V/5V lossless WAV music decoder, WMA / MP3 / FM speaker panel modules, support breakpoint memory Features: 1. Support USB, SD, support for external signal directly switch 2. Support for stereo Bluetooth (Bluetooth3.0EDR) 3. Support USB / SD / Bluetooth / FM / LINE switch automatically. 4. Support MP3 / WMA / WAV lossless songs. 5. Support USB / SD card switch, switch songs song selection 6. Support Bluetoot the song, the next song, adjust volume, EQ, play / pause, mute, shut down. 7. Support FAT16, FAT32 file system. 8. Support MP1 Layer3, MP2 Layer3, MP3 Layer3 version of the song. 9. Support 32-320kbps of MP3 songs. 10. Support power and memory function, continue playing the song played before the power and volume. 11. Support cycle mode 12. Power supply: DC 12V: 7-12V, DC5V: 3.7-5V 13. Panel dimensions: 92 * 35 * 40mm How to connect: Connection: 2P circuit board electrically connected to 12V (GND Ground, + 12V positive); FM: ANT FM radio antenna connected to the welding hole; The audio output: 5P row seat then press the icon audio output R / L / GND; and your amplifier board R / L / GND pair are connected. Or connected to the AUX input jack The audio input (AUX): 3P-row seat according to the illustrated audio inputs L-IN / GND / R-IN Note: Can not connect two power supply in the same time (5V / 12V choose one) Package included: 5 x Decoding panel 5 x Remote control