8pin p dip

Buy OPTOCOUPLER 8PIN P DIP 3K75V HCPL-7800-000E for R246.13

P[CB MOUNT LOW NOISE JFET OPERATIONAL AMPLIFIERS; OFFSET=3.0mV;

Buy 26 WAY PCB MOUNT SOCKET; DIP STRAIGHT P=2.54 170598 for R3.87

SUB-MICROAMP COMPARATOR WITH OPEN DRAIN OUTPUT / DIP / 1.6-5.5V / DUAL / -40 TO 125DEG

SINGLE CHANNEL 12 BIT DIGITAL TO ANALOGUE CONVERTER; DIP PACKAGE; SPI INTERFACE

MICROCONTROLLER; DIP PACKAGE; OTP; 8-BIT; 40MHz; 20 x I/O LINES; 1 x TIMER WIDE PACKAGE

Description TOUCH OR P/BUTTON CONTROL OF AC POWER IDEAL FOR UNIVERSAL OR SHADED-POLE MOTOR SPEED CONTROL More Products View More Products

CMOS FLASH MICROCONTROLLER; DIP40 PACKAGE; 20MHz; 33xI/O LINES; 8x10 BIT ADC CHANNELS; 2xCCP; SPI; I2C; USART; 3x TIMERS; 2xCOMPARATORS

8 BIT MICROCONTROLLER / 33 x I/O / PWM / 4 TIMERS / USART / 8K EPROM / CCP / 0 TO 70DEG

Description QUAD 2 INPUT XOR GATE, PCB MOUNT More Products View More Products

Description 10 bit Serial ADC, Differential Input, 16-Pin PDIP More Products View More Products

Description MULTIPLEXER, DUAL, 4 INPUT More Products View More Products

Description PCB MOUNT QUAD 2 INPUT MULTIPLEXER More Products View More Products

Recording Format: AVCHD Signal Format: i, p/p/p, p, p Recording Modes: x and x 720 High Definition Recording Media: SDHC memory card Number of image sensors: 3, Progressive CMOS Size of image sensors: 1/4" Pixels on image sensors: 3.05 Million Lens: Leica Dicomar Focus: Auto and Manual, Focus Assist Button, Switch to Focus Ring Shutter Speed: 1/2sec - sec Optical Zoom: 12x Image Stabilization: Optical Filter Thread Diameter: 43mm Manual White Balance: Yes Viewfinder: Yes, Color, pixels LCD Monitor: Yes; 2.7", Color, pixels Progressive Scan: Yes, (Native p and p) Connectors: HDMI, USB2.0, Composite, Component Mono/Stereo Recording: Stereo Microphone In: Yes, 1/8" and balanced 8pin, 48v phantom power Manual Audio Level Controls: Yes Headphone Jack: Yes, 1/8" Speaker: Yes Flash: No Wireless Remote: Yes Onboard Video Light: No Accessory Shoe: Yes, cold shoe Battery: Yes, mAh Dimensions: H 5.2", L 12", W 5.3" Weight: 2.2lbs.

Specifications: 1.Photoresistor (LDR) based line following 2.Individual wheel control 3.Chipset: LM393 4.Material: Electrical components 5.Color: See picture 6.Board Size:10.4*7.2cm The assembly steps: Step 1: Welding circuit - Electric welding part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance is important to use the multi meter to confirm resistance is correct Step 2: Mechanical assembly - The red line is connected to the 3V positive power supply, the yellow line grounding, the excess wire can be used for the motor wire. Step 3: The installation of a photoelectric circuit - Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test. Step 4: Vehicle debugging - The right direction is along the universal wheel direction if you press and hold the left photoresistor - The wheels on the right side of the car should be rotated. Press and hold the right photoresistor - The wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring on the back side. Note: The battery is not included. Package Included: 1 x Base board 1 x 35mm Wheels 1 x Rubber Wheel bands 1 x AA Battery holder 1 x Screw set 1 x LM393 Chipset 1 x 8pin DIP Socket 10 x Resistor 2 x Gearded DC Motors 2 x Electrolytic capacitor 2 x Light dependant resistors 2 x Transitors 2 x White LED 2 x Red LED 1 x Power switch 4 x 70mm Leads