5pcs low

Buy 5pcs Low 3.5ohm PCA9306 Dual Bidirectional Voltage-Level Conversion Module Converter for R575.00

Buy 5Pcs Low Voltage DC 1.8V 3V 5V 6V 12V 2A Motor Speed Controller PWM 1803B... for R459.00

5Pcs A87 4 Channel Optocoupler Isolation Module High And Low Level Expansion Board For Arduino Description:1. Function: Use the low level to control the high level. Such as the use of single-chip 3V or 5V voltage control 9V or 12v voltage.2. HVCC should not exceed 24V. Output OUT1 / OUT2 / OUT3 / OUT4 output current equal to HVCC / 5.1K, absorption current 500ma.3. This module uses TLP281 chip (for Toshiba).4. Schematic:Input and output instructions: Input: IN1 / IN2 / IN3 / IN4, then the microcontroller or Arduino IO port, GND and the Arduino development board connected to the GND.IN1 / IN2 / IN3 / IN4 controls OUT1 / OUT2 / OUT3 / OUT4, respectively.Output: OUT1 / OUT2 / OUT3 / OUT4Output: HVCC: Connect the controlled high voltage positive, HGND connected to the controlled high voltage negativeUse: When IN1 is high, the corresponding OUT1 voltage is equal to HVCC, when IN1 is low, the OUT1 voltage is equal to HGNDUse examples The following example shows how to use the microcontroller's IO port to control the 24V motor rotation. Figure motor operating voltage of 24V,red ' ' that the motor power positive, black '-' that the motor power supply negative. When the microcontroller IO_0 output high, the motor rotate,when the IO_0 port output low, the motor stops rotating.Package included:5 x A87 4 Channel Optocoupler Isolation Module

5Pcs 5V 1-Channel H/L Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load: AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 5 x 1 Channel H/L trigger optocoupler relay module

5Pcs Jog Type Touch Sensor Module For Arduino Description: This is jog type capacitive touch switch sensor module based on a touch detection IC TTP223B. Normally, the output is low level(at mode of low power consumption). When the finger touch the corresponding location, output will be high(at quick speed mode). When the module do not be touched for 12 seconds, the mode would switch to low-power mode. It can be installed in the module, such as plastic, glass, non-metallic material surface. But not cover thin sheets(metal) on the surface of the module. Just touch the correct position, it can be hidden in walls, desktops and other parts to be buttons. Allows you to remove the troubles of conventional push-type buttons. Feature: Low power consumption Can replace the traditional key With four M2 screw holes, easy for operation Specification: Operating voltage: DC 2.0V ~ 5.5V VOH: VCC 0.8V VOL: VCC 0.3V Sink current: 8mA @ VCC = 3V, VOL = 0.6V Source current: -4mA @ VCC = 3V, VOH = 2.4V Response time: 220ms (at mode of low power consumption) and 60ms (at quick speed mode) Size: 24 x 24 x 7.2mm Package included: 5 x Capacitive jpg type touch sensor module

5Pcs LM35DZ TO-92 LM35 Precision Centigrade Temperature Sensor Feature: 0.5°C Ensured Accuracy (+25°C) Suitable for Remote Applications Low Cost Due to Wafer-Level Trimming Operates from 4 to 30 V Less than 60-μA Current Drain Low Self-Heating, 0.08°C in Still Air Low Impedance Output, 0.1 Ω for 1 mA Load Package included: 5 x LM35DZ Precision Temperature Sensor

5Pcs Soil Hygrometer Humidity Detection Moisture Sensor For Arduino Description: This is a summary of the soil moisture sensor can be used to detect moisture, when the soil is dry, the module outputs a high level, whereas output low. Using this sensor make an automatic watering system, so that your garden plants without people to manage. Operating voltage: 3.3V~5V. Adjustable sensitivity (shown in blue digital potentiometer adjustment) Dual output mode,analog output more accurate. A fixed bolt hole for easy installation. With power indicator (red) and digital switching output indicator (green). Having LM393 comparator chip, stable. Panel PCB Dimension: 3cm x 1.5cm. Soil Probe Dimension: 6cm x 2cm. Cable Length: 21cm. VCC: 3.3V-5V. GND: GND. DO: digital output interface(0 and 1). AO: analog output interface. Instructions for Use: 1. Soil moisture module is most sensitive to the ambient humidity is generally used to detect the moisture content of the soil. 2. Module to reach the threshold value is set in the soil moisture, DO port output high, when the the soil humidity exceeds a set threshold value, the module D0 output low. 3. The digital output D0 can be connected directly with the microcontroller to detect high and low by the microcontroller to detect soil moisture. 4. The digital outputs DO shop relay module can directly drive the buzzer module, which can form a soil moisture alarm equipment. 5. Analog output AO and AD module connected through the AD converter, you can get more precise values of soil moisture. Package Included: 5 x Soil moisture detector module 5 x Probe 5 x 2P Jumper Cable

5Pcs HC-12 433 SI4463 Wireless Serial Module Remote 1000M With Antenna Note: HC-11 cannot communicate with the HC-12, they work independently, in pairs Features: Supply voltage: 3.2V~5.5V. (If the module you want to work long hours in the emission state, it is recommended that when the supply voltage exceeds 4.5V threaded a 1N4007 diode to prevent module built-in LDO heated) Default address range (open field test): About 600m (maximum communication distance adjustable reach 1000m, the baud rate is 5000bps) Default idle current: 16MA (In different working modes operating current is different) Module dimensions: 27.8 x 14.4 x 4mm Operating frequency range: 433.4-473.0MHz, up to 100 channels of communication The maximum transmit power: 100mW (settable) Module support software upgrade Default factory settings: Mode FU3, baud rate is 9600bps, communication channels CH001 (433.4M) Package included: 5 x HC-12 433 Serial module AT command set:   Module parameters, AT command set AT command is used to set the parameters of the function module and switching modules need to exit the setting mode after setting to take effect. Meanwhile, modify the parameters and functions, power-down is not lost.   Enter the command mode: The first entry mode - normal use (has the power) in the first 5-pin "SET" is set low; The second mode of entry - power, 5th pin "SET" again first set low on power. Both methods can make the module into AT command mode, release ("SET" pin is not connected low) to exit command mode. After the exit command mode, if you change the module function, the function will be cut to the appropriate state. The second way is fixed in serial format 9600, N, 1 into the AT.   Instructions: 1. AT Test instructions Example: Send module commands "AT", the module returns "OK".   2. AT + Bxxxx Change the serial port baud rate command. You can set the baud rate is 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps. The factory default is 9600bps. Example: Set the module serial port baud rate is 19200bps, please send module command "AT + B19200", the module returns "OK + B19200".   3. AT + Cxxx Change the wireless communication channel, selectable from 001 to 127 (more than 100 radio channels after the communication distance not guaranteed). The default value is 001 radio channels, operating frequency is 433.4MHz. Step channel is 400KHz, the operating frequency of the channel 100 is 473.0 MHz.   Example: Set module to channel 21, please send module command "AT + C021", the module returns "OK + C021". After exiting the command mode, the module in the first 21 channels, operating frequency is 441.4 MHz. Note: Because the wireless receiver module sensitivity HC-12 is relatively high, the baud rate is greater than when air 58000 bps, 5 must be shifted to the adjacent channel use. When the air baud rate is not greater than 58000 bps, if the short distance (10 meters) communication, but also need to stagger five adjacent channel use.   4. AT + FUx Change the module serial pass-through mode, there FU1, FU2 and FU3 three modes. Module default mode is FU3, two serial pass-through mode module must be set to the same communication. See detailed above, "wireless serial pass-through" part. Example: Send module commands "AT + FU1", the module returns "AT + OK".   5. AT + Px The default setting is 8, maximum transmit power, communication distances. Transmit power level is set to 1, the minimum transmission power. In general, the transmission power of each drop 6dB, communication distance will be reduced by half. Example: Send module commands "AT + P 5", the module returns "OK + P5". After exiting the command mode, the module transmit power is +11 dBm. Package included: 1 x HC-12 module

5pcs 2 Channel DC 12V Relay Module Solid State Low Level Trigger For Arduino 240V2A Package contains 1 X item of the smallest listed variant.

5pcs BESTEP 1 Channel 5V Low Level Solid State Relay Module With Fuse 250V2A For Auduino Package contains 1 X item of the smallest listed variant.

5pcs HC-05 Wireless Bluetooth Serial Module With Baseplate For Arduino Note: This module does not suitable for IOS system. Pin serial port descriptions: PIO8 connect LED, indicates the status of working, after powered the module flashing, different states in different flashing intervals. PIO9 connect LED, indicates successful connecting module, after successful mating bluetooth serial port, LED long lights. PIO11 state switch pin (high level) -> AT command response to the work state, low level or dangling -> Bluetooth regular work status. On module with a reset circuit, re-power to complete the reset. Main module setup steps: 1. PIO11 set high. 2. Power ON, the module into the AT command response status. 3. HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity, no flow control. 4. Serial send characters "AT + ROLE = 1 r n", successful return "OK r n", which r n for carriage return. 5. PIO set low, re-power, module as the main module, automatic search from module to establish a connection. Feature: 6V - 4.5V power supply; Support connect Android phones with Bluetooth; The default baud rate: 9600 can be modified according to the data sheet; Package included: 5 x HC-05 Wireless Bluetooth Serial Module

5Pcs NE555 Pulse Frequency Duty Cycle Adjustable Module Square Wave Signal Generator Features: 1. As a square wave signal generator,generates a square wave signal used for experimental development. 2. Used to drive a stepper motor for generating a square wave drive signal. 3. Generate adjustable pulse for MCU. 4. Generate adjustable pulse,to control circuitry associated. 5. Size: 31mm x 22mm 6. Main chip: NE555 7. Input Voltage: 5V-15V DC. When power supply is 5V, the output current can be 15 MA around; when 12V power supply, the output current can 35 MA around 8. Input current: >=100 MA 9. Output amplitude: 4.2V V-PP to 11.4V V-PP. (Different input voltage, the output amplitude will be different) 10. Maximum output current: >=15MA (5V power supply, V-PP greater than 50%), >=35MA (12V power supply, V-PP greater than 50%) 11. Output with LED indication(low level,LED will on; high level,LED will off;low frequency, the LED flashes) 12. The output frequency range is selectable: LF file: 1Hz ~ 50Hz IF file: 50Hz ~ 1kHz High-frequency file: 1KHz ~ 10kHz HF file: 10kHz ~ 200kHz 13.The output duty cycle can fine-tune; duty cycle and frequency is not separately adjustable; adjusting the duty cycle will change the frequency Package included: 5 x NE555 Pulse Frequency Duty Cycle Adjustable Module

5Pcs Speed Measuring Sensor Counter Motor Test Groove Coupler Module For Arduino Application: Widely used in motor speed detection, pulse count, the position limit, etc.   Feature:   Using imported groove optical coupling sensor, width 5mm. It have the output state light, if output high level, the lights are off. if output low level,it on. If it covered,it will output high level;otherwise it output low level. Good signal and waveform, with strong driving ability for more than 15mA. The working voltage of 3.3V to 5V. Output: digital switch output (0 and 1). Equipped with a fixed bolt hole, easily install. Small board PCB size: 3.2 cm x 1.4 cm. Use the LM393 wide voltage comparer.   Specification:   The DO output interface can be directly connected to a micro-controller IO port, if there is a block detection sensor, such as the speed of the motor encoder can detect. DO modules can be connected to the relay, limit switch, and other functions, it can also with the active buzzer module, compose alarm.   Wiring specification: VCC Connect the positive 3.3 5 v power supply GND Connect power negative DO TTL switch signal output AO This module does not work Package included: 5 x Speed Measuring Sensor Module

5pcs CJMCU-1232 ADS1232 Analog-to-Digital Converter Board ADS1232IPWR Ultra Low Noise For Arduino Package contains 1 X item of the smallest listed variant.

5Pcs 5V MAX485 TTL To RS485 Converter Module Board For Arduino Feature: Operating voltage: 5V On-board MAX485 chip A low power consumption for the RS-485 communication Slew-rate limited transceiver 5.08mm pitch 2P terminal Convenient RS-485 communication wiring All pins of chip have been lead to can be controlled through the microcontroller Board size: 44 x 14mm Package included: 5 x MAX485 TTL to RS485 module

5Pcs AD9833 Programmable Microprocessor Serial Interface Module Features: Digitally programmable frequency and phase 12.65 mW power consumption at 3 V 0 MHz to 12.5 MHz output frequency range 28-bit resolution: 0.1 Hz at 25 MHz reference clock Sinusoidal, triangular, and square wave outputs 2.3 V to 5.5 V power supply No external components required 3-wire SPI interface Extended temperature range: ?40ﾰC to 105ﾰC Power-down option Update rate: 25(max) VOUT maximum: 0.65V VOUT minimum: 38mV VOUT temperature Coefficient: 200ﾰ Input high voltage: 1.7-2.8V Input low voltage: 0.5-0.7V Input current: 10ﾵA Input capacitance: 3pF Operating temperature range: ?40ﾰC to 105ﾰC, typical specification at 25ﾰC Size: 17*12mm / 0.66*0.47' Package includes: 5 x Signal Generator Module

5Pcs Infrared Obstacle Avoidance Sensor For Arduino Smart Car Robot Description: The sensor module light is adaptable to the environment, the working voltage of 3.3 V to 5 V. It has a pair of infrared transmitting and receiving tube, when detecting direction meet with obstacles (reflecting surface), reflected infrared receiving by the tube. After the comparator circuit processing, green indicator will light up, at the same time the signal output interface output a digital signal (a low level signal), can be adjust the detection distance through the potentiometer knob, effective distance range 2 ~ 80 cm, easy to assemble and use. So it can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and so on many occasions. Package included: 5 x Arduino obstacle avoidance sensor

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Specification: Input Power Supply: 12V DC Load Voltage: AC240V 2A Maximum operating current: 13.8mA Trigger mode: low level Input control signal voltage: (0-2.5V low state relay OFF) (3.3-5V state high relay ON) Blue KF301 terminal connection control line is more convenient. Module interface: DC +: positive power supply (by relay voltage power supply) DC-: connect power negative CH: Relay Module signal triggering end (Low level trigger effective) Note: Power must be DC voltage and need to be consistent with the voltage relay Package Included: 5 x Low Level Relay Module 5pcs 1 Channel DC 12V Relay Module Solid State Low Level Trigger For Arduino 240V2A 5pcs 1 Channel DC 12V Relay Module Solid State Low Level Trigger For Arduino 240V2A 5pcs 1 Channel DC 12V Relay Module Solid State Low Level Trigger For Arduino 240V2A

Specifications: Color: Black Shape: Cylindrical Capacitance: 10 Farad Max Voltage: 2.7V ESR: 60mΩ permissible voltage: 2.5V Lead wire type: Same direction Diameter: 10mm Length: 26mm Allowable deviation: -20~40 (%) Dielectric material: Super farad Frequency: Low frequency Application scope: Low voltage Features: - Good quality - High cost performance - Low temperature and low internal resistance and low leakage current - The volume is small, but the capacity is big. The capacity is bigger than the same volume electrolytic capacity about 30~40 times. - The power density of the capacitor is 10~100 times of the battery. It can even reach about 10kw/kg. - Charging speed is quick. - With super long life which is up to more than 100 thousand times, and is more than 10-100 times the battery. - Less pollution. Application for: - CPU intelligent home appliance, meter, tax control machine, controller, air conditioning, recorder, MP3, car audio, telephone, solar lights, real-time clock etc. - Power supply of small power devices, such as: intelligent water meter, gas meter, disinfection cabinet, electronic door locks, solar equipment, digital set-top boxes, toys, etc.; - Electric starting system, with the battery used in various internal combustion engines such as cars, tanks, diesel locomotives, can effectively protect the battery and prolong its service life, reduce the power loss with capacity, especially in low temperature and battery case, ensure reliable start Package included: 5 x Super farad capacitor

Description: The CC1101-868MHz RF module is low cost and highly integrated UHF transceiver designed for low power wireless applications. These pro certificate modules, operating in the license free 868 MHz ISM band, can be easily integrated into your application, thereby reducing development time and cost. Features: Low power UHF wireless transceivers @868MHz Support FSK, GFSK, ASK/OOK and MSK Configurable data rate 1.2K to 500kps Independent 64 bytes FIFO for TX & RX buffer Packet handling including address recognition Support Wake-On-Radio Support Clear Channel Assessment (Listen-before-Talk) RSSI Output & Link Quality Indictor SPI Interface Wide Operating Voltage 2~3.6V Applications: AMR – Automatic Meter Reading Two-way RKE – Remote Keyless Entry Low power telemetry Home and building automation Wireless alarm and security systems Industrial monitoring and control Wireless sensor networks Electrical characteristics: Recommended operating conditions: Operating ambient temperature range: -40°C - +85 °C Operating supply voltage: 2V - 3.6 V Package included: 5 x CC1101-868MHz RF Module

Buy 5pcs WEAH-D222 60W Speaker Crossover High and Low 2 Frequency Divider Sound Quality Upgrade Tool for R390.00

Buy 5pcs JDY-22 4.2 Ultra Low Power BLE bluetooth Module Serial Transmissions External Antenna for R325.00

Buy 5pcs CJMCU-250E BMA250E Sensor Module Three-axis Low G Acceleration Sensor Triaxial Accelerometer SP for R428.22

Buy 5pcs JDY-22 4.2 Ultra Low Power BLE bluetooth Module Serial Transmissions Exter for R322.94

Buy 5pcs AC-DC 5V 2A Switching Power Supply Board Low Ripple Power Supply Board 10W for R461.82

Buy 5pcs WEAH-D224 80W Speaker Crossover High and Low 2 Frequency Divider Sound Quality Upgrade Tool for R325.00

Buy 5pcs 5V USB Cooling Fan Governor LED Dimming Module Low Power Timer Board with for R542.19

Buy 5pcs WEAH-D224 80W Speaker Crossover High and Low 2 Frequency Divider Sound Qua for R301.00

Buy 5pcs CJMCU-250E BMA250E Sensor Module Three-axis Low G Acceleration Sensor for R385.89

Buy 5pcs 1 Channel 5v Relay Module High And Low Level Trigger... for R229.00