5pcs key

5Pcs 4 x 3 Matrix 12 Key Array Membrane Switch Keypad Keyboard For Arduino Description: Pad Size: 68.9 x 76 x 0.8mm Cable length: 85mm (include connector) Connector: dupont 7 pins, 0.1 inch (2.54mm) Pitch Mount style: Self-Adherence Max. circuit rating: 35VDC, 100mA Insulation spec.: 100M Ohm, 100V Dielectric withstand: 250Vrms (60Hz, 1min) Contact bounce: 5ms Life expectancy: 1 million closures Weight: 7g Package included: 5 x Membrane switch Matrix Array 12 key

5PCS Squeeze Spoof Toy Stress Reliever Toy With Key Chain Random Color Description: The product is a funny stress reliever toy, you can repeat boring actions make you calm down to vent your pressure and discontent. It also has a key chain. Color & Patterns: Random Specification: Material: Flexible Plastic Size(about):3.5 x 3.5 x 5 cm Package Included: 5 x Squeeze Toy

5pcs Whistle Key Finder Keychain Sound LED With Whistle Claps

5pcs TM1637 6-Bits Tube LED Display Key Scan Module DC 3.3V To 5V Digital IIC Interface Package contains 1 X item of the smallest listed variant.

5Pcs Jog Type Touch Sensor Module For Arduino Description: This is jog type capacitive touch switch sensor module based on a touch detection IC TTP223B. Normally, the output is low level(at mode of low power consumption). When the finger touch the corresponding location, output will be high(at quick speed mode). When the module do not be touched for 12 seconds, the mode would switch to low-power mode. It can be installed in the module, such as plastic, glass, non-metallic material surface. But not cover thin sheets(metal) on the surface of the module. Just touch the correct position, it can be hidden in walls, desktops and other parts to be buttons. Allows you to remove the troubles of conventional push-type buttons. Feature: Low power consumption Can replace the traditional key With four M2 screw holes, easy for operation Specification: Operating voltage: DC 2.0V ~ 5.5V VOH: VCC 0.8V VOL: VCC 0.3V Sink current: 8mA @ VCC = 3V, VOL = 0.6V Source current: -4mA @ VCC = 3V, VOH = 2.4V Response time: 220ms (at mode of low power consumption) and 60ms (at quick speed mode) Size: 24 x 24 x 7.2mm Package included: 5 x Capacitive jpg type touch sensor module

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA 5Pcs 4x4 16-Key Matrix Keypad Keyboard Module 16 Buttons For Arduino 5Pcs 4x4 16-Key Matrix Keypad Keyboard Module 16 Buttons For Arduino Specification: 4 x 4 Matrix Keyboard 16 Buttons Size: 39 x 43mm Package included: 5 x 16 key 4 x 4 matrix keypad keyboard 5Pcs 4x4 16-Key Matrix Keypad Keyboard Module 16 Buttons For Arduino 5Pcs 4x4 16-Key Matrix Keypad Keyboard Module 16 Buttons For Arduino

Feature:   Onboard 2W mono amplifier (5V power supply up to 3W) can directly connected speakers (recommended with 4Ω3W speakers), 3.5mm gold-plated headphone jack can be accessed by headphones or external audio. With MicroUSB power supply interface, using mobile bank power or USB charger power supply, can also be used 3.7V lithium battery, USB 5V power supply. Support TF card (mobile phone memory card), U disk playback mode. With a speaker terminal without soldering, easy wiring.   1) Support MP3 format, power automatically play, led status turn to red. 2) Support U disk (tested with 32G), TF card (tested with 16G) playing mode, power default TF card mode, if the TF card does not exist automatically jump to U disk mode, and both devices are installed, you can manually set the playback mode, please refer to the key operation instructions.   Key operation instructions:   "Prev / V--" key: "short press" to switch "Previous" song, "long press" to switch "volume down" "Next / v ++" key: "short press" to switch "next song", "long press" to switch "volume increase" "P / P / Mode" key: "short press" to "play / pause" switch, "long press" for the U disk, TF card "mode" select "Repeat" key: "short press" for the "single / full song" cycle switch (no long press function)   Note:   1. Long press time about 2S 2. If you use U disk mode, the recommended 5V power supply, some U disk does not support 3.7V power supply.   Specifications:   Power supply range: 3.7 - 5.5V Product size: 45mm * 36mm   Package includes:   5 x MP3 Lossless Decoder Board

Features: 5PCS 5CM Simulation Porcelain Large Bowl Chinese Food Key Chain Home Decoration All is traditional Chinese food. Have noodles, rice, syrup, and so on. It look so real, so real to believe it is real food. But you can`t eat because it`s not a real food. Forget that, I`m hungry. Come for the most delicious food in the world. Specifications: Size: Diamater 5.5CM Material: Plastic Pattern:  Random Warning: The dish is simulation food, please keep it away from child who`s under 3 years old in case they eat them by accident. Package Included: 1set x  Simulation Large Bowl Chinese Food (1set included 5 pieces)

Buy 5pcs 6x6mm Key Module Touch Push Button Switch Module Electronic Component for R139.35

Buy 5pcs AT42QT1070 5-Pad 5 Key Capacitive Touch Screen Sensor Module Board DC 1.8 to 5. - Free Shipping for R1,335.00

Buy 5pcs 433MHz Remote Key PCB Circuit Board For Peugeot 307 / Citroen 73373067C for R645.89

Buy 5Pcs RFID IC Keyfobs 13.56 MHz Keychains NFC Key Card ISO14443A MF Classi For Smart Access Control S for R72.00

Buy 5pcs Big Key Module Push Button Switch Module With Hat High Level Output Electronic for R124.26

Buy 5Pcs 4 x 3 Matrix 12 Key Array Membrane Switch Keypad Keyboard for R184.57

Buy 5Pcs TM1638 Chip Key LED Display Module 8 Bits Digital LED Tube for R474.56

Buy 5pcs 433MHz DC 12V One Key Gate RF Wireless Remote Control Garage Door Transmit for R449.00

Buy 5Pcs 12x12mm Key Switch Module Touch Tact Switch Push Button Non-locking With C for R190.00

Buy 5pcs 433MHz Remote Key PCB Circuit Board For Peugeot 307 / Citroen 73373067C for R659.50

Buy 5pcs Touch Memory TM Key Card RW1990 iButton Copy Card Rewritable RFID Clone Dupl... (COLOR.: GREEN) for R267.00

Buy 5Pcs 4 x 3 Matrix 12 Key Array Membrane Switch Keypad Keyboard Geekcreit for Arduino - products that for R215.00

Buy 5Pcs 433MHz Auto Pair Copy Remote 4 Buttons Garage Gate Door Wireless Remote Control with Key Ring for R549.00

Buy 5Pcs DANIU 433mhz Electric Cloning Universal Gate Garage Door Remote Control Fob Key Fob for R470.00

Description: Suitable for the following batteries: Lead acid: 12V 24V 36V 48V Lithium battery: 2 strings, 3 strings, 4 strings, 5 strings, 6 strings, 7 strings....13 strings, 14 strings, 15 strings This product uses LCD display, the LCD capacity consumption is 70% lower than the conventional digital tube, and the display is clear. Ultra wide voltage input, 63V high voltage input still can work smoothly. Voltage range: 6-63V Current: 3-4mA Size: 63 x 25 mm Setting steps: 1. Disconnect the power to display the power, press and hold the setting key to power the power, then release the set key, enter the setting interface, electricity display the current setting parameters; 2. Short press set key to select the battery specification: P/L/F (P=12V lead acid, L=3.7V lithium battery, F=3.2V phosphate iron lithium battery); 3. Set the number of battery strings by short function keys. The function keys and setting keys can select the battery series up or down. 4. After the setup is completed, the power is reset automatically, and the data can be saved automatically. Package included: 5 x LCD capacity meter

Product Parameters :   1, Onboard TTP229 capacitive touch-sensitive 16 key IC 2, Working Voltage: 2.4V-5.5V 3, You can set the output mode, key, mode, maximum output time and fast/low power selection 4, PCB Board Dimensions: 49  x 64.5 (mm)   Package Included:   5x Touch Sensor Module

Specifications: 1. Ultra wide voltmeter range: DC 4.5-40V 2. 5V / 2A output current capacity (when the input voltage is at 6.5~40V, can stabilize to output 5.0V voltage) 3. One key ("output enable" button) switch USB output, one key (“low power ” button) into ultra-low power consumption 4. Voltmeter can be self calibration, there will never be inaccurate voltmeter problems!! 5. Reverse connection protection, reverse connect not burning 6. With over-current and over-temperature protection 7. With USB power indicator 8. With wiring terminals, easy access to the line 9. High efficiency and low ripple Module instructions: After power module can be real-time detection of voltage, when you need to charge for mobile phone, Ipad, MP3 and other digital products, touch the "output enable" button, the USB power indicator lights, USB output 5.0V voltage; when you need to close the digital tube, touch the "low power" button, then the module into the ultra-low power standby mode, USB output is also shut down accordingly. Module use: Ultra wide input voltage, can be used for cars / battery vehicles / motorcycles, used to monitor the battery voltage, timely grasp the battery state, can be used for various voltage measurement purposes. The output current capability of the 5.0V and 2A is sufficient to meet various USB devices, and the voltage is very stable. Note: this module defaults to D+ D- short connection, compatible with most mobile phone charging, and set aside a variety of mobile phone to identify resistance position, if you need to join the resistance identification, please cut off the wire connection D+ D-. Package included: 5 x DC-DC 2 in 1 6.5V-40V to 5V buck step down power module

Features: The voltmeter resolution: ±0.1V The voltmeter digital display range: 0V - 45V The voltmeter input voltage range: DC 4V - 40V Output voltage: continuous adjustable (1.3V -37V) Output current: 2A (Max 3A) Size:65 x 35mm Description: With terminal block Over-heat protection and short circuit protection function LED digital voltmeter tube, it can adjustable accurate aimed at your multimeter. Press the key "S1" to let the display show the input or output voltage. when the green led light, it shows output, the red show input. Touch the button to switch the measurement input or output voltage, and indicator light shows which voltage is being measured, it can save the settings, even if the power off and restart. Using 150KHz internal oscillation frequency, belonging to the second generation switching voltage regulator, low power consumption and high efficiency. Note: To guarantee the accuracy of the voltmeter, make sure the input voltage above 4V. The input voltage must be 1.5V higher than the output voltage or 1.5V above. Package included: 5 x LM2596 DC-DC 1.3V -37V 3A adjustable buck power module

Description: Note: This module does not suitable for IOS system. The core module HC-06 main modules, leads the interface includes VCC, GND, TXD, RXD, KEY pin high trigger to clear the pairing information re search led indicate Bluetooth connection status, flash unpaired slow flash indicates paired but not slave connection, Always follow machine connected Backplate settings LDO input voltage of 3.6~~6V unpaired current is about 30mA, paired 10mA, input voltage prohibit more than 7V absolute prohibition of reverse power! Interface level 3.3V, can be directly connected the various SCM (51, AVR, PIC, ARM, MSP430, etc.), the 5V MCU also can be connected directly, without MAX232 can not go through the MAX232! Open to effective distance of 10 meters, over 10 meters is also possible, but not of this the quality of the connection of the distance do to ensure The pair later when full-duplex serial use, do not need to know anything about the Bluetooth protocol, but only supports 8 data bits, 1 stop bit, no parity communication format, which is the most commonly used communication format does not support other formats. Support to establish a Bluetooth connection through AT commands set the baud rate, passkey, set parameters are saved after. Bluetooth connection is automatically switched to the pass-through mode. Wireless serial Bluetooth port with free extension cable. With transparent shrink tube, dust and beautiful, and there is a certain degree of anti-static capabilities. Size:3.57cm x 1.52cm Tips: TXD: the sender, usually expressed as its sender, the normal communication must be connected to another device RXD. RXD: the receive side, generally expressed as the receiving end of their normal communication to another device connected to TXD. Package included: 5 x HC-06 wireless bluetooth transceiver

  Description: ENNIO SY1001A-MJIDS11 Touch Key 10" LCD RFID Password Video Door Phone Intercom System Wth IR Camera 1000 TV Line Remote Access Control MJIDS Access Controller  - The MJIDS  is a standalone access control, they use the latest microprocessor technology to operate door strikes and security systems that require a momentary (timed) or latching dry contact closure. All programming is done through the keypad. Codes and operating parameters are stored within the microprocessor and can not be lost due to power failure. Support 125KHz EM card. Low power consumption (standby input current: 3 access modes: Card, Card or PIN, Card with PIN. Can work as a standalone keypad (PIN code length: 4-6 digits). Relay output load can be 3A max. Water resistant. Remote Control  - This is a remote control device for Door Access Control System, after you connect it on your system, you can press the remote control to open the door remotely, the distance can reach up to 6-20 meters 125KHz RFID Cards  - These are 5pcs 125KHz RFID Proximity ID Card, they can work with the product which has 125Khz RFID card reader. MJIDS Access Controller: Intput Voltage:12VDC Input current: User Capacity: 500 User Card,  1 Password Card Type: RFID compatible card Frequency: 125Khz Read range: 10-50mm Wiring connections: Electric Lock, Exit Button Remote Control: Detecting distance: 3-10cm Operation frequency: 125Khz Each comes with Key ring included Compatible with all RFID ID card reader to gain access Each token pre-programmed with unique ID which is printed on it Indoor monitor: Screen: 10" TFT LCD (16:9 display) Resolution: 960 * 480 Power supplied by: power adapter Power adapter: input: AC 100-240V 50/60Hz output: DC 15V 2000mA Adapter type: US EU AU UK plug Adapter cable length: 1.45m/ 4.75ft Consumption: working state: 8W, standby state: 0.5W Call duration time: approx. 120 seconds Monitor duration time: approx. 60 seconds Material: plastic Outdoor unit: Material: plastic & metal LED: 6 x infrared LED lights Camera: 1/3 CMOS  1000 TV Line Viewing angle: 92 degrees Consumption: calling state: 12W, standby state: 0.1W Valid distance (6 x 0.75mm² copper wires): 80m/ 262.4ft Working temperature: -10¿¿¿ to +50¿¿¿ Working humidity: ≤85%  

Note: It works for universal unencrypted 125kHz RFID cards/tags only! Not work for other frequencies. Not work for encrypted cards like HID, Indala, Cobra, APCiK, Paradox, Radio, Honeywell, Kaba, Isonas, etc. It can copy 125kHz RFID ID cards with EM4305, EM4100, T5577 CET5200, 6610, 8210. Reading distance is 0 - 6cm. Built-in buzzer and LED indicator. Handheld and portable design. Working independently. Easy to use, read & write. Powered by 2x AAA battery(not included). With 5x writable key cards. ETEKJOY Handheld 125kHz RFID ID Card/Tag Reader Writer Copier Duplicator + 5PCS Writable Blank Cards

Just buy one effect and you have it all This incredible effect mixes 3 different effects in wonderful combination: LED effect, similar to our LED DEVIL (5pcs 3watt leds with different colors: red, green, blue, orange, white) LED STROBE: powerful white LEDs (8pcs 1watt) LASER effect: wonderful red (150mW) / green (50mW) laser patterns A lot of different internal programs to make life simple DMX-control: 1channel for easy operation or 9 channels for full control. Standalone: sound activated (internal mic) or automatic. Master/slave: wonderful synchronized shows. 3-digit LED display for easy menu navigation IEC mains input + output for easy linking Key activated on/off switch and emergency switch (interlock) input for additional safety Complies to EN/IEC 60825-1 2007 for Laser Safety