5pcs diy led display

Buy 5pcs DIY LED Display Rotation Finger Tip Gyro Kit Electronic Production LED Display Module Kit... for R649.00

Buy 5Pcs DIY LED Lamp Kit LED Flash Set Electronic Production Kit for R558.73

Buy 5pcs Red LED Display DC-DC 5V to 3.3V/9V/12V/24V USB Adjustable Buck-boost Power Supply Voltage R... for R439.00

5Pcs MAX7219 Red 8 Bit Digital Tube LED Display Module For Arduino MCU Description: MAX7219 is an integrated serial input / output common-cathode display drivers, which connects the microprocessor and 8 bit 7-segment digital LED display, you can also connect a bar graph display or 64 separate LED. Includes an on-chip type B BCD encoders, multi-channel scanning loop, segment word driver, but also a 8x8 static RAM that stores each data. Only one external register is used to set the current of each LED segment. A convenient four-wire serial interface can connect all common microprocessor. Each data can be addressed in the update without rewriting all displays. MAX7219 also allows the user to select each data encoding or no coding. The entire device includes a 150μA low-power shutdown mode, analog and digital brightness control, a scan-limit register allows the user to display 1-8 bit data, there is an all LED light detection mode. Feature: 0.36 inch Common cathode Only need three IO ports can drive 8 bit digital tube The module compatible of 5V / 3.3V microcontroller (51 / AVR / STM32...) PCV board four corners of the fixed copper stud, which can effectively precent short circuit accidents happen Wiring instructions (a program, for example, you can pick any IO port definition can be modified in the program): VCC to 5V, GND to GND, DIN to P00, CLK to P02, CS to P01 Note: VCC and GND do not reversed, it would burn the chip. 51 MCU P0 port requires pull-up resistor, if your device does not have a pull-up resistor can be connected to other ports data lines. Package included: 5 x MAX7219 8 bit digital tube module 20 x Copper pillar 20 x Screws

5Pcs DIY Double Color LED Flash Lights Kit Electronic Production NE555+CD4017 Practice Learning Kit

DIY LED CUBE KIT 4*4*4 BLUE LIGHTS, 64PCS LEDS, SOUND CONTROL, ELECTRONIC LEARNING - E0804 This DIY kit aims at making a beautiful light cube which was designed with many kinds of 3D display modes. You can press the two buttons to switch for each display mode. The LEDs make up beautiful blue light for great visual perception. Features: Adopts 64pcs highlight long leg LEDs which can display wonderful effects at night. Built-in about 20 kinds of 3D display effects. Two buttons to switch modes, convenient for operation. Can switch different modes, can auto-play all the modes; can set the speed of modes or set sound control mode. High sensibility for sound control, simple for DIY but interesting for use. It's very nice for electronic enthusiasts and students as a DIY kit. Specifications: Power Supply: USB Interface LED Quantity: 64pcs PCB Board Size: 7 * 9cm / 2.75 * 3.54in Package Size: Approx. 13 * 8 * 2.5cm / 5.12 * 3.15 * 0.98in Package Weight: 76g / 2.68oz Package List: 1 * DIY LED Cube Kit 1 * USB Cable

5pcs TM1637 6-Bits Tube LED Display Key Scan Module DC 3.3V To 5V Digital IIC Interface Package contains 1 X item of the smallest listed variant.

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: Operating voltage:DC 4 ~ 30V Measure voltage: DC 0 ~ 100V Minimum resolution(V): 0.1V Measure current:50A (require external shunt) Minimum resolution(A): 0.1A Operating current: Display: three 0.28" LED digital tube Display color: Red and Blue (two-color display) Refresh rate: about 300mS / times Measure accuracy: 1% (± 1 digit) Operating temperature: -10 to 65° c Operating Humidity: 10 to 80% (non-condensing) Working pressure: 80 to 106 kPa Applications:Suitable for automotive/electric cars/motorcycles battery monitoring or other products voltage current measurement Wiring: Black line (thin): vacant or buck circuit (module) negative Red line (thin): power supply+ Black line (thick): COM, common measuring Red line (thick): PW+, measuring terminal voltage input positive Yellow line (thick): IN+, current input+ (Please refer to the wiring diagrams for more details) Notice: The voltage between the thin red and thin black lines must be within DC 4-30V The ammeter can only be connected to the negative of the device under test Exceeds 5A, long-term full load working continuously, it is recommended that the measurement side of the leads are directly soldered to the socket When the black thin line vacant, it is better to use insulating tape around the exposed part of the wire, to prevent short circuits If just be used as a voltmeter, it is recommended that the yellow line and the black line were connected together, to prevent the ammeter digital flashing It is unsuitable to use this meter to test current less than 10A. ￢ﾀﾋPackage included: 5 x Digital Voltmeter Ammeter Meter 5 x Current Shunt 5 x Cable 5pcs 0.56 Inch Blue Red Dual LED Display Mini Digital Voltmeter Ammeter DC 100V 50A Panel Amp Volt Voltage Current Meter Tester 5pcs 0.56 Inch Blue Red Dual LED Display Mini Digital Voltmeter Ammeter DC 100V 50A Panel Amp Volt Voltage Current Meter Tester 5pcs 0.56 Inch Blue Red Dual LED Display Mini Digital Voltmeter Ammeter DC 100V 50A Panel Amp Volt Voltage Current Meter Tester

Buy 5pcs DIY Electronic Kit Set Cartoon Bear LED Flash Light Production Kit Simple Flash Parts DIY Sk... for R189.00

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: The dimming circuit can make the voltage at both ends of the bulb change in the range of tens to 200 volts, and the dimming effect is remarkable. In the circuit, R2, R3, R4, RP1, C1 and VT1 constitute a single junction transistor oscillator circuit, which is used to generate trigger pulses.When the capacitor is charged by R4 and RP1, the voltage Ue increases gradually. When the Ue reaches the peak voltage, e B1 turns on and the voltage on the capacitor outputs a pulse voltage to R2 via e-b1. Because the resistance of R4 and RP1 is large, when the voltage on capacitor drops to the trough voltage, the current supplied by R4 and RP1 is less than the trough current, which can not meet the conduction requirements, so the single-junction transistor restores the blocking state. Thereafter, the capacitor recharges and repeats the above process. As a result, a sawtooth wavy voltage is formed on the capacitor and a pulse voltage is formed on R2. During each half cycle of AC voltage, the single-junction transistor will output this pulse to trigger the gate of the thyristor, which will turn on the thyristor and light up the lamp. Change the resistance value of RP1, that is, change the oscillation frequency of sawtooth wave, thus change the size of thyristor conduction angle, and then change the output voltage of controlled rectifier circuit to achieve the purpose of adjusting the brightness of the bulb. Input voltage: 220V Size: 45 x 30mm Package Included: 1 x DIY BT33 Table Lamp Dimmable Optical Circuit Kit DIY BT33 Table Lamp Dimmable Optical Circuit Kit LED Display Module Kit DIY BT33 Table Lamp Dimmable Optical Circuit Kit LED Display Module Kit DIY BT33 Table Lamp Dimmable Optical Circuit Kit LED Display Module Kit

Buy 5pcs DIY 4017 Running Water Light NE555 LED Horse Race Lamp Flash Kit for R313.31

Buy 5pcs Electronic DIY LED Dimming Lights Series and Parallel Circuit Technology S for R236.62

Buy 5pcs DIY Blue LED Round Flash Electronic Production Kit Component Soldering Training Practice Board for R210.00

Buy 5pcs DIY Gradient LED Flash Light Production Kit Electronic 4017NE555 for R459.00

Buy 5pcs RGB LED Module Board for M5GO Kit STEM DIY Traffic Light Compatible M5 Core for R389.06