5pcs 30pin driver

Feature: This cable generally use for LED screen, is very convenience to use. Suitable for any 30 pin, 1 channel, 6 bit interface. Package included: 5 x 30Pin Cable

5Pcs LED Driver Charging Constant Current Voltage Step Down Buck Module Package contains 1 X item of the smallest listed variant.

Buy 5pcs A4988 Driver Module Stepper Motor Driver Board with Heatsink for R266.26

Feature: This cable generally use for LED screen, is very convenience to use. Suitable for any 30 pin, 1 channel, 6 bit interface. Package included: 1 x 30Pin Cable

Feature: This cable generally use for LED screen, is very convenience to use. Suitable for any 30 pin, 1 channel, 6 bit interface. Package included: 30 x 30Pin Cable

Feature: This cable generally use for LED screen, is very convenience to use. Suitable for any 30 pin, 1 channel, 6 bit interface. Package included: 10 x 30Pin Cable

5pcs L293D L293 L293B DIP / SOP Push-Pull Four Channel Motor Driver IC Feature: Quantity: 5pcs Part number: L293D Manufacturer: ST Pin no: 16 pins Package included: 5 x L293D driver IC

5Pcs MAX7219 Red 8 Bit Digital Tube LED Display Module For Arduino MCU Description: MAX7219 is an integrated serial input / output common-cathode display drivers, which connects the microprocessor and 8 bit 7-segment digital LED display, you can also connect a bar graph display or 64 separate LED. Includes an on-chip type B BCD encoders, multi-channel scanning loop, segment word driver, but also a 8x8 static RAM that stores each data. Only one external register is used to set the current of each LED segment. A convenient four-wire serial interface can connect all common microprocessor. Each data can be addressed in the update without rewriting all displays. MAX7219 also allows the user to select each data encoding or no coding. The entire device includes a 150μA low-power shutdown mode, analog and digital brightness control, a scan-limit register allows the user to display 1-8 bit data, there is an all LED light detection mode. Feature: 0.36 inch Common cathode Only need three IO ports can drive 8 bit digital tube The module compatible of 5V / 3.3V microcontroller (51 / AVR / STM32...) PCV board four corners of the fixed copper stud, which can effectively precent short circuit accidents happen Wiring instructions (a program, for example, you can pick any IO port definition can be modified in the program): VCC to 5V, GND to GND, DIN to P00, CLK to P02, CS to P01 Note: VCC and GND do not reversed, it would burn the chip. 51 MCU P0 port requires pull-up resistor, if your device does not have a pull-up resistor can be connected to other ports data lines. Package included: 5 x MAX7219 8 bit digital tube module 20 x Copper pillar 20 x Screws

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: 1. The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0V to 5V pulse. (or 0V to 3.3V pulse if you solder SJ2 closed on the EasyDriver) 2. EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. 3. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4, 6, or 8 wire stepper motors. 4. It provides much more flexibility and control over your stepper motor, when compared to older versions. The microstep select (MS1 and MS2) pins of the A3967 are broken out allowing adjustments to the microstepping resolution. The sleep and enable pins are also broken out for further control.cjmcu made. Features: 1. MS1 and MS2 pins broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) 2. Compatible with 4, 6, and 8 wire stepper motors of any voltage 3. Adjustable current control from 150mA / phase to 750mA / phase 4. Power supply range from 7V to 30V. The higher the voltage, the higher the torque at high speeds 5. Distribution pin, not welded, this module is open source Note: Do not connect or disconnect a motor while the driver is energized.This will cause permanent damage to the A3967 IC. Chip data: https://www.alldatasheetcn.com/datasheet-pdf/pdf/83571/ALLEGRO/A3967.html Package included: 5 X A3967 easy driver stepper motor driver board 5pcs DC 7V To 30V 150mA To 750mA A3967 Easy Driver Stepper Motor Driver Board For Arduino 5pcs DC 7V To 30V 150mA To 750mA A3967 Easy Driver Stepper Motor Driver Board For Arduino 5pcs DC 7V To 30V 150mA To 750mA A3967 Easy Driver Stepper Motor Driver Board For Arduino

Specifications: · 300W 8A 7-32V to 0.8-28V DC CC CV Buck Step-Down Converter Power Supply Step Down Module Adjustable Voltage Regulator LED Driver · High-power, constant current LED driver · Battery charger · Vehicle-mounted power supply · Low voltage system power supply · Non-isolated step-down CC CV Buck module with on-board LED load indicator · Input voltage: DC 7-32 V · Output Voltage: DC 0.8-28 V (Adjustable) · Output Current: 8A (MAX), more than 60Deg please strengthen heatsink · Continuous Current Range: 0.2-8A Adjustable · Output Power: 300W (MAX) · Conversion efficiency: 95% (more input voltage, more efficiency) · Output ripple: 50mV · Working Temperature: industrial (- 40 ° c to +85 °c) (environmental temperature, more than 40 degrees, please reduce power to use, or - enhance cooling) · No-load current: 20mA (input 24V,Output 12V for reference) · Voltage regulation: ± 1% · Load regulation: ± 1% · Dynamic response speed: 200uS 5% · Short circuit protection: YES · Input Reverse protection: No (please comply with a reverse protection or connect a diode at input parts.) · Size: 65 x 47 x 22 mm · On-board LED load indications: red = load present (eg. 'battery charging'), green = no load (eg. 'battery charged' or output disconnected) Features: 1. Fixed turn lamp current is 0.1 times the current value(Used to identify whether the battery is fully charged When charging). 2. Made from a dedicated benchmark IC and high-precision current sensing resistor, proving a more stable constant current, (when 20°C to 100°C constant current 1A, temperature drift less than 1%). Particularly suitable for LED driver. 3. High output current, the max output current can reach 8A. 4. Four high frequency capacitance, can lower output ripple, enhance the work stabilization. 5. Double heat sink design. MOS schottky diode independent heat sink,which heat dissipation is good, and won't affect each other. 6. Using large size Sendust Core and double pure copper wiring, improve working efficiency, reduce fever. 7. 3296 multiturn potentiometer,high accuracy voltage and current regulation, good stability. 8. Double color lamp, working condition be clear at a glance 9. Voltage and current are adjustable,wich effect is good. Applications: 1. High-power LED driver. 2. Lithium battery(or lead accumulator) charge. 3. Vehicle-mounted power supply. 4. Low voltage system power supply. 5. 6V, 12V, 14V, 24V battery charge. 6. On-board laptop power supply. 7. regulated power supply. 8.Low voltage power supply system. Module adjustment: ￢ﾀﾋ 1. When the module output voltage can not be adjusted (the output voltage is always equal to the input voltage) Please adjust the potentiometer counterclockwise 20 laps (20 turns) or more till it works.￢ﾀﾋ 2. Turn trimmers CLOCKWISE to INCREASE, ANTICLOCKWISE to DECREASE. 3. When adjust the blue potentiometer,please use a multimeter to monitor the voltage 4. The trimmer nearest the voltage output adjusts the output CURRENT (CC) 5. The trimmer nearest the voltage input adjusts the output VOLTAGE (CV) Charger application - intructions: 1. First determine the float voltage and charging current required by the battery to be charged (the ‘target battery'). The target battery disconnected from the module output, apply a voltage of 7V - 32V to the module input, being sure to observe correct polarity. 2. Using the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the charging current required by target battery. 4. Using the CV trimmer, adjust the module's output voltage to the float voltage required by the target battery. 5. Connect the target battery to the module output, observing correct polarity. Charging of the battery should commence ￢ﾀﾋ Constant current LED Driver Application - Instructions: 1. First determine the operating current and maximum operating voltage of the LED you need to drive. 2. With the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the operating current of your LED. 4. Adjust the CV trimmer to make the output voltage reach the maximum LED operating voltage. 5. Connect LED, test. Package included: 5 x 8A 300W buck adjustable power supply module

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: This is a 8 x 8 LED dot matrix display module that can be used to display characters and graphics and it is simple to control it. Features: Compatibility: Compatible with Arduino UNO R3 / Arduino Mega2560. Libraries for Arduino: Max72xxPanel and Adafruit_GFX Resolution: 8 x 8 Driver: LED color: Highlight Red Display size: 60.2X60.2mm LED size: 5mm Cascadable: Yes Number of cascadable node: 32(MAX) Driver IC: MAX7219 Working voltage: 4.5-5.5V Working current: 250mA(MAX) Interface logic voltage: 5V Interface type: SPI Great for Arduino DIY projects Package included: 5 x OPEN-SMART Dot Matrix LED 8x8 Seamless Cascadable Red LED Dot Matrix F5 Display Module 5pcs OPEN-SMART Dot Matrix LED 8x8 Seamless Cascadable Red LED Dot Matrix F5 Display Module 5pcs OPEN-SMART Dot Matrix LED 8x8 Seamless Cascadable Red LED Dot Matrix F5 Display Module 5pcs OPEN-SMART Dot Matrix LED 8x8 Seamless Cascadable Red LED Dot Matrix F5 Display Module

Buy 5pcs DRV8833 2 Channel DC Motor Driver Module Board 1.5A 3V-10V for R251.55

Buy 5pcs 7W 9W 12W 15W 7-15W LED Driver Input AC110V/220V Power Supply Built-in Drive Power Supply 300mA for R295.00

Buy 5Pcs PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module for R653.93

Buy 5pcs DC 9V 12V 18V 24V 20W Adjustable LED Driver PWM Controller DC DC Step for R199.00