3pcs pack breadboard power

Buy 3Pcs/Pack Breadboard Power Supply Board Module with MicroUSB Support 3.3V/5V Du for R262.18

Buy 3pcs MB102 Breadboard Power Supply Module Adapter Shield 3.3V/5V Geekcre for R155.00

3pcs Geekcreit MB-102 MB102 Solderless Breadboard + Power Supply + Jumper Cable Kits For Arduino Package contains 1 X item of the smallest listed variant.

3Pcs 8-Channel Logic Level Translator Converter Bi-Directional Module Introduction: If you've ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. This level converter also works with 2.8V and 1.8V devices. What really separates this Logic level converter from our previous versions is that you can successfully set your high and low voltages and step up and down between them safely on the same channel. Each level converter has the capability of converting 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side. The level converter is very easy to use. The board needs to be powered from the two voltages sources (high voltage and low voltage) that your system is using. High voltage (5V for example) to the 'HV' pin, low voltage (3.3V for example) to 'LV', and ground from the system to the 'GND' pin. Feature: 8-channel high-voltage and low-voltage logic bidirectional translation Mini size, 4.1cm x 1.8cm Comes with 2 rows of 6pin, unsoldered Compatible breadboard, can be directly inserted in the breadboard Note: (For example: High voltage: 5V, low voltage: 3.3V) HV connect 5V power supply LV connect 3.3V power supply GND connect negative, two power supply commons LVx input and output is 3.3V TTL, HVx input and output is 5V TTL, LVx and TVx bidirectional transfers Package includes: 3 x Eight Channel Logic Level Translator Converter

3Pcs 8-Channel Logic Level Translator Converter Bi-Directional Module 3Pcs 8-Channel Logic Level Translator Converter Bi-Directional ModuleIntroduction:If you've ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be.The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time.This level converter also works with 2.8V and 1.8V devices.What really separates this Logic level converter from our previous versions is that you can successfully set your high and low voltages and step up and down between them safely on the same channel.Each level converter has the capability of converting 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side.The level converter is very easy to use.The board needs to be powered from the two voltages sources (high voltage and low voltage) that your system is using.High voltage (5V for example) to the 'HV' pin, low voltage (3.3V for example) to 'LV', and ground from the system to the 'GND' pin.Feature:8-channel high-voltage and low-voltage logic bidirectional translationMini size, 4.1cm x 1.8cmComes with 2 rows of 6pin, unsolderedCompatible breadboard, can be directly inserted in the breadboardNote: (For example: High voltage: 5V, low voltage: 3.3V)HV connect 5V power supplyLV connect 3.3V power supplyGND connect negative, two power supply commonsLVx input and output is 3.3V TTL, HVx input and output is 5V TTL, LVx and TVx bidirectional transfersPackage includes:3 x Eight Channel Logic Level Translator Converter

Features: 1. Standard striboard is great for prototyping and building circuits but it can be time consuming to use with components with certain pin configurations such as ICs as much time has to be spent breaking tracks to ensure no shorts exist across opposite component pins. This bpard gets around that problem by having isolated groups of pins. 2. Solderable PCB breadboards, single-sided PCB, matches breadboards with Power Rails. These boards are especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place. Specifications: Material: Bakelite Length: 220mm Width: 100mm Thickness: 1.2mm Hole Dia: 1mm Package included: 3 x Single Side Copper Prototype Paper PCB Breadboard

Buy 3pcs 3S Lithium Battery Pack Power Indicator Board Electric Vehicle Battery Power for R210.00

Buy 3pcs Portable Mobile USB Power Bank Charger Pack Box Battery Module Case for 1x18650 DIY Power Bank for R136.00

Description: This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Ω speaker at over half a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. There's even a volume trim pot so you can adjust the volume on the board down from the default 24dB gain. This board is a welcome upgrade to basic "LM386" amps! CJMCU The A+ and A- inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the Audio- pin to ground. The output is "Bridge Tied" - that means the output pins connect directly to the speaker pins, no connection to ground. The output is a high frequency 250KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly. CJMCU Comes with a fully assembled and tested breakout board. We also include header to plug it into a breadboard and a 3.5mm screw-terminal blocks so you can easily attach/detach your speaker. You will be ready to rock in 15 minutes! Features: - Output Power: 2.5W at 4Ω, 10% THD, 1.5W at 8Ω, 10% THD, with 5.5V Supply - 50dB PSRR at 1KHz - Filterless design, with ferrite bead + capacitors on output. - Fixed 24dB gain, onboard trim potentiometer for adjusting input volume. - Thermal and short-circuit/over-current protection - Low current draw: 4mA quiescent and 1uA in shutdown mode Note: Speaker is not included, use any 4 ohm or greater impedance speaker. Package included: 3 x Audio Power Amplifier

Description: 1. Use aluminum alloy U disk shell to install internal motherboard. 2. The interface definition is directly marked on the enclosure. 3. 5V, 3.3V at the same time to provide external use, convenient for you to connect 5V and 3.3V target board. 4. The shell characters use laser engraving, never fade off and permanent clarity. 5. The internal motherboard with 500MA self recovery fuse, completely protect your expensive computer motherboards. 6. Red and blue double color LED indicator lamp, it is convenient for you to observe the working state of ST-LINK V2 at all times. 7. Distribution dupont wire, so that you can easily deal with the wire sequence of different target board. 8. The outer packing is made of anti-static bag and sealed pack by automatic sealing machine. It is safe and reliable and not afraid of static electricity or water. 9. Note: r ed, black, gold, green, grey, white, blue, pink color random delivery Features: 1. Support a full range of STM32 SWD interface debugging, 4 wire interface simple (including power), fast speed, work stability; interface definition shell is directly marked. 2. Support a full range of STM8 SWIM download debugging (common development environment such as IAR, STVD and so on are supported); support software version is as follows: 1) XTW LINK ST Utility 2.0 and above 2) STVD 4.2.1 and above 3) STVP 3.2.3 and above 4) IAR EWARM V6.20 and above 5) IAR EWSTM8 V1.30 and above 6) KEIL RVMDK V4.21 and above 6 and above 3. Support firmware automatic upgrade, factory firmware has been upgraded to the latest V2.J17.S4. 4. Increase the 5V power output, output I / O port are protected, not afraid of operating mistakes caused by LINK, ST, V2 damage. 5. The interface uses pure copper gold-plated 2.54 space simple ox horn socket with 20CM Dupont wire 6. Using U aluminum alloy shell to protect the motherboard 7. With data package, data contains: 1) XTW, LINK, ST, V2 driver; 2) KEIL, MDK (4.60) development environment (and other common development environment) 3) IAR, STM8 (1401) development environment (and other common development environment) 4) STVD STM8 development environment (and other common development environment) 5) A number of classic STM32 data (including a large number of examples of source code and video tutorials) 6) A number of classic STM8 data (including a large number of examples of source code and learning experience) Package included: 3 x 3.3V 5V XTW ST-LINK V2 STM8 / STM32 programmer with 20cm dupont wire