3pcs open smart

3Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load: AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 3 x 1 Channel H/L level trigger optocoupler relay module

3Pcs/Pack Ultrasonic Sensor/Ranging Sensor Acrylic Fixed Bracket for Smart Chassis Car

3Pcs/Pack KittenBot 23x12.2x29mm SG90 9g Mini Servo with 25cm Wire for Smart Robot Car

3Pcs Orange Rubber Wheels + 3-6v TT Motors DIY Kit For Arduino Smart Chassis Car Accessories

3Pcs 2 Way Relay Module With Optocoupler Protection Feature: The relay contact capacity 250V 10A Relay outputs normally open, normally closed Active low 5V relay signal input voltage range: 0-5V VCC system power JD-VCC power relay Default 5V relay JD-VCC and VCC shorted on it Package included: 3 x 2 Way Relay Module With Optocoupler Protection

3Pcs HC-12 433 SI4463 Wireless Serial Module Remote 1000M With Antenna Note: HC-11 cannot communicate with the HC-12, they work independently, in pairs Features: Supply voltage: 3.2V~5.5V. (If the module you want to work long hours in the emission state, it is recommended that when the supply voltage exceeds 4.5V threaded a 1N4007 diode to prevent module built-in LDO heated) Default address range (open field test): About 600m (maximum communication distance adjustable reach 1000m, the baud rate is 5000bps) Default idle current: 16MA (In different working modes operating current is different) Module dimensions: 27.8 x 14.4 x 4mm Operating frequency range: 433.4-473.0MHz, up to 100 channels of communication The maximum transmit power: 100mW (settable) Module support software upgrade Default factory settings: Mode FU3, baud rate is 9600bps, communication channels CH001 (433.4M) Package included: 3 x HC-12 433 Serial module AT command set:   Module parameters, AT command set AT command is used to set the parameters of the function module and switching modules need to exit the setting mode after setting to take effect. Meanwhile, modify the parameters and functions, power-down is not lost.   Enter the command mode: The first entry mode - normal use (has the power) in the first 5-pin "SET" is set low; The second mode of entry - power, 5th pin "SET" again first set low on power. Both methods can make the module into AT command mode, release ("SET" pin is not connected low) to exit command mode. After the exit command mode, if you change the module function, the function will be cut to the appropriate state. The second way is fixed in serial format 9600, N, 1 into the AT.   Instructions: 1. AT Test instructions Example: Send module commands "AT", the module returns "OK".   2. AT + Bxxxx Change the serial port baud rate command. You can set the baud rate is 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps. The factory default is 9600bps. Example: Set the module serial port baud rate is 19200bps, please send module command "AT + B19200", the module returns "OK + B19200".   3. AT + Cxxx Change the wireless communication channel, selectable from 001 to 127 (more than 100 radio channels after the communication distance not guaranteed). The default value is 001 radio channels, operating frequency is 433.4MHz. Step channel is 400KHz, the operating frequency of the channel 100 is 473.0 MHz.   Example: Set module to channel 21, please send module command "AT + C021", the module returns "OK + C021". After exiting the command mode, the module in the first 21 channels, operating frequency is 441.4 MHz. Note: Because the wireless receiver module sensitivity HC-12 is relatively high, the baud rate is greater than when air 58000 bps, 5 must be shifted to the adjacent channel use. When the air baud rate is not greater than 58000 bps, if the short distance (10 meters) communication, but also need to stagger five adjacent channel use.   4. AT + FUx Change the module serial pass-through mode, there FU1, FU2 and FU3 three modes. Module default mode is FU3, two serial pass-through mode module must be set to the same communication. See detailed above, "wireless serial pass-through" part. Example: Send module commands "AT + FU1", the module returns "AT + OK".   5. AT + Px The default setting is 8, maximum transmit power, communication distances. Transmit power level is set to 1, the minimum transmission power. In general, the transmission power of each drop 6dB, communication distance will be reduced by half. Example: Send module commands "AT + P 5", the module returns "OK + P5". After exiting the command mode, the module transmit power is +11 dBm. Package included: 1 x HC-12 module

Smart sensor Simple push button indication Battery power indication Locate stud and metal with audio and LCD wave bar indication Locate A/C wire with audio and arrow indication Normal scan and deep scan by push button selection. Simple LCD display with wave bar. Audio alert and icon function indication Operated with 9v battery(included) We are at Shop 43 Frontline between the Postnet & Simply Asia Moffet on Main Lifestyle centre Charlo (Port Elizabeth) Mon to Fri 9:00 to 18:00 Closed Fri from 12:15 to 14:15 Sat 9:00 to 15:00 We will be open every Sunday till Christmas Sun 9:00 to 14:00 Public holidays 9:00 to 15:00 Debit & Credit cards Accepted

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Summarize: LC 12V WiFi relay module carried a ESP8266 WiFi module and microcontroller. It will send the serial port instructions to the cell phone APP and Implementation within the local area network (LAN) for wireless control relay. The function and characteristics: Onboard ESP8266 WIFI module, AP mode 5 client can be connected at the same time; Module has two work modes: 1, cell phones, carry on the WiFi module;2, mobile phone and WiFI module Carrying on the same router, by mobile phone APP to control relay; Transmission distance: 1, the open environment, the mobile phone when carrying on the WIFI module maximum transmission distance of 400 m; 2, when the WiFI module and cell phone carrying on the router at the same time the signal transmission distance in accordance with the router on the weak; Onboard 12 v, 10 A / 250 v AC 10 A / 30 v DC relay, absorb 100000 times continuously; Module with diode effusion protection, short response time; Module baud rate: 9600,8,1,0,0. Introduced the hardware and instructions: Size: 45*28mm The board function description: IN +,IN-: 12 v power input; TX,RX and GND: a serial port debug pins; Introduction: Onboard the ESP8266 WIFI module has three work modes: STA (client), AP (hot), the STA + Ap(hot +client), according to the workings of a module to the corresponding choice of WIFI module working mode.Module need before use serial debugging software and USB to TTL module send serial command was carried out on the WIFI module configuration (don't power outages after configuration is complete, as some of the parameters of WIFI module cannot be saved when the power is cut off), mobile phone and WIFI module after establishing a network connection can use the phone APP control relay. App download from here ! Package included: 3 x ESP8266 12V WiFi Relay Networking Smart Home Phone APP Remote Control Switch 3Pcs ESP8266 12V WiFi Relay Networking Smart Home Phone APP Remote Control Switch 3Pcs ESP8266 12V WiFi Relay Networking Smart Home Phone APP Remote Control Switch 3Pcs ESP8266 12V WiFi Relay Networking Smart Home Phone APP Remote Control Switch

Description: This WIFI relay based on AI-Thinker ESP-01S WIFI module. It is designed for smart home, Internet of thing and other DIY project. With this smart relay, you will easy to DIY your smart switch to control any device by your phone anywhere. Product parameters: Product size: 37 * 25mm Operating voltage: DC5V Communication: WIFI (ESP8266 module) Transmission distance: the maximum transmission distance of 400m (open environment, mobile phone equipped with WIFI module) Load: 10A/250VAC 10A/30VDC, the relay pull 100,000 times Download:https://pan.baidu.com/s/1cHBbbw Usage: 1. Power it by DC 5v; 2. Open your phone WLAN then connect the WiFi ESP8266-XXXX, Power word:12345678 3. Open the ESP8266 Controller.app (Installed it in your android phone before) 4. Set IP Address: 192.168.1.1 than you can control your device via the wifi relay module Package included: 3 x ESP8266 ESP-01S Relay Module(Not Includ ESP-01S WIFI Module)

Summarize: LC 5V WiFi relay module carried a ESP8266 WiFi module and microcontroller. It will send the serial port instructions to the cell phone APP and Implementation within the local area network (LAN) for wireless control relay. Function and characteristics: Onboard ESP8266 WIFI module, AP mode 5 client can be connected at the same time; Module has two work modes: 1, cell phones, carry on the WiFi module;2, mobile phone and WiFI module Carrying on the same router, by mobile phone APP to control relay Transmission distance: 1.The open environment, the mobile phone when carrying on the WIFI module maximum transmission distance of 400 m 2.When the WiFI module and cell phone carrying on the router at the same time the signal transmission distance in accordance with the router On the weak Onboard 5 v, 10 A / 250 v AC 10 A / 30 v DC relay, absorb 100000 times continuously Module with diode effusion protection, short response time Module baud rate: 9600,8,1,0,0. The board function description:   Size: 45*28mm IN +,IN-: 5 v power input TX,RX and GND: a serial port debug pins Introduction: Onboard the ESP8266 WIFI module has three work modes: STA (client), AP (hot), the STA + Ap(hot +client), according to the workings of a module to the corresponding choice of WIFI module working mode.Module need before use serial debugging software and USB to TTL module send serial command was carried out on the WIFI module configuration (don't power outages after configuration is complete, as some of the parameters of WIFI module cannot be saved when the power is cut off), mobile phone and WIFI module after establishing a network connection can use the phone APP control relay. When cell phone equipped with WiFi module sends commands in the following order: (The default baud rate 115200) 1, AT+CWMODE=2, namely AP mode is selected; 2, AT+RST, reset; 3, AT+CIPMUX=1, open multiple connections; 4, AT+CIPSERVER=1,8080, configure the TCP server, set the port; 5, AT+CIOBAUD=9600 set the baud rate to 9600. (working in relays to control the baud rate 9600) 6, AT+CIFSR to view the AP mode IP address, such as: the APIP, "192.168.4.1"; 7, Cell phone WIFI signal connection name starts with AI-THINKER or ESP8266; 8, In the "TCP connection" address and port into the APP, such as 192.168.4.1 and 8080; 9, Click on the grey box relays can be controlled. 10,  Document: Applications:   1. Home Automation 2. Industrial IOT Applications 3. Lighting Controls Package included: 3 x ESP8266 5V WiFi Relay Module

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Feature: This is a smart hardware development kit that supports the cloud. The simple and cost-effective IoT development board does not require you to understand the complex knowledge of network, TCP/IP, etc. As long as you can C language, you can quickly realize it with Anxin's wit cloud SDK. Secondary development, this DEMO board can use the mobile phone flow control onboard RGB colorful lights, mobile phone APP, can display the ambient brightness through the photoresistor, the code can be made to your own remote as long as you can modify it for half an hour. Control equipment, the system generates APP (Android, IOS) for free, open SDK, you only need to do the API UI of the APP to develop a finished product. Wit Cloud Beta User Guide and ESP8266SDK: https://pan.baidu.com/s/1eQDaQau SDK compilation environment cygwin: https://pan.baidu.com/s/1kTIpKJ9 Wit Cloud Developer Forum: https://club.gizwits.com Wit cloud platform: https://site.gizwits.com/zh-cn/developer Mobile APP source code and related materials can be downloaded to the wit cloud platform registration developer number. Package includes: 3 x ESP8266 Development Board 3 x ESP-12F Expansion Module 3pcs ESP8266 Development Board ESP-12F Expansion Module Board Secondary Development Hardware Development Kit 3pcs ESP8266 Development Board ESP-12F Expansion Module Board Secondary Development Hardware Development Kit 3pcs ESP8266 Development Board ESP-12F Expansion Module Board Secondary Development Hardware Development Kit

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA 3Pcs Infrared Obstacle Avoidance Sensor For Arduino Smart Car Robot Description: The sensor module light is adaptable to the environment, the working voltage of 3.3 V to 5 V. It has a pair of infrared transmitting and receiving tube, when detecting direction meet with obstacles (reflecting surface), reflected infrared receiving by the tube. After the comparator circuit processing, green indicator will light up, at the same time the signal output interface output a digital signal (a low level signal), can be adjust the detection distance through the potentiometer knob, effective distance range 2 ~ 80 cm, easy to assemble and use. So it can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and so on many occasions. Package included: 3 x Arduino obstacle avoidance sensor 3Pcs Infrared Obstacle Avoidance Sensor For Arduino Smart Car Robot 3Pcs Infrared Obstacle Avoidance Sensor For Arduino Smart Car Robot 3Pcs Infrared Obstacle Avoidance Sensor For Arduino Smart Car Robot

Buy 3pcs Smart Life Wireless Wifi Switch Universal Automation Smart Home Module Timer DIY Wifi Remote Co for R575.18

Buy 3Pcs SONOFF S26 10A AC90V-250V Smart WIFI Socket UK Wireless Plug Power Sockets Smart Home Switch Wo for R890.00

Buy 3Pcs SONOFF S26 10A AC90V-250V Smart WIFI Socket IL Wireless Plug Power Sockets Smart Home Switch... for R949.00