3pcs navigation signal

3Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 3 x Micro SD TF card module

3Pcs Sound Detection Sensor Module LM393 Chip Electret Microphone For Arduino Features: The product boast of output signal instruction. Single-channel signal output. Output valid signal is low and the light will be bright. Specification: Weight: 4g Size: 3.1 x 1.6 x 0.8cm Operating current pressure: 4V - 6V Package included: 3 x Sound detection sensor module

3Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module Description: You’ve always wanted to output analog voltages from a microcontroller, the MCP4725 is the DAC that will let you do it! The CJMCU-MCP4725 is an I2C controlled Digital-to-Analog converter (DAC). A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller. Digital to analog converters are great for sound generation, musical instruments, and many other creative projects! This version of the CJMCU-MCP4725 Breakout fixes a few issues with the board including the IC footprint, the I2C pinout, changes the overall board dimensions to better fit your projects, and a few more minor tweaks. This board breaks out each pin you will need to access and use the MCP4725 including GND and Signal OUT pins for connecting to an oscilloscope or any other device you need to hook up to the board. Also on board are SCL, SDA, VCC, and another GND for your basic I2C pinout. Additionally, if you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this. Feature: 12-bit resolution I2C Interface (Standard, Fast, and High-Speed supported) Small package 2.7V to 5.5V supply Internal EEPROM to store settings Package included: 3 x CJMCU-MCP4725 I2C DAC Breakout Development Board Module

3Pcs ESP8266 ESP-12E Remote Serial Port WIFI Transceiver Wireless Module Description: ESP8266-12E is an enhanced version ESP8266-12, improve peripheral circuitry increases impedance matching, the signal output is better, whether it is stable or anti-jamming capability, have been greatly improved! For users before selecting the ESP-12, it does not matter even if the product has been made, enhanced version is fully compatible with previous firmware, the pin has added six IO ports on the basis of the ESP-12, SPI leads Note: We don't offer any supports,sorry for the inconvenience Package included: 3 x ESP8266 ESP-12E Remote Serial Port WIFI Transceiver Wireless Module  

3Pcs 2 Way Relay Module With Optocoupler Protection Feature: The relay contact capacity 250V 10A Relay outputs normally open, normally closed Active low 5V relay signal input voltage range: 0-5V VCC system power JD-VCC power relay Default 5V relay JD-VCC and VCC shorted on it Package included: 3 x 2 Way Relay Module With Optocoupler Protection

3Pcs 15W TDA7297 Dual-Channel Amplifier Board For Arduino Features: AC / DC, 2.0 / dual channel / stereo,12V/2A when using, the output power of 15W +15 W, peak up 25W +25 W Can be accessed by two 4-8Ω 10-50W speakers A large volume of small size High signal to noise ratio Upgraded version of the radiator, wider and thicker, better cooling effect Fit for Bookshelf speakers, CRT televisions, radios, and other small amplifiers Specifications: 1. Working voltage: DC 9-15V 2. Power: 15W +15 W 3. Maximum power:30W+30W 4. Output Impedance: 4-8Ω Package included: 3 x TDA7297 Version Amplifier Boards

Feature: Note: This module does not suitable for IOS system. TTL data transparent transfer between a host Bluetooth device Build-in CSR company Bluetooth chip BC417143 Bluetooth specification v2.0 + EDR Works with any USB Bluetooth adapters Default Baud Rate: 9600, pairing code 1234, the working mode SLAVE Coverage up to 30ft Built in antenna Mini Size Using mainstream CSR Bluetooth chip, Bluetooth V2.0 protocol standards Serial module operating voltage 3.3V, 10 meters from the general The working current: pairing: 30mA ~ 40mA Sleep current: not sleep For GPS navigation systems, utility meter reading systems, industrial control systems mining site Can be used with a Bluetooth laptop computer plus a Bluetooth adapter, PDA and other devices to connect seamlessly   Specification: Power input: +3.3V DC Signal coverage: 30ft Size: 26.9 x 13 x 2.2mm Application: This module is mainly used for wireless transmission of data in the field a short distance. And PC can be easily connected Bluetooth device, you can also exchange data between two modules. Avoid cumbersome cable connections, direct serial cable replacement.   Package included: 3 x HC-06 30ft wireless bluetooth RF transceiver module

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: Trigger mode: High level 5V relay module Can be used for microcontroller development board module or home appliance control 5V - 12V TTL control signal Can control DC or AC signal, also 220V AC load Normally open / closed contact Power indicator Controlled lights bright when pull and not shine when disconnect Increase the transistor drive relay coils, control pins high impedance Control pins have pull down circuit to prevent malfunction of relay vacant Package included: 3 x 5V 1 channel relay module 3Pcs 5V Relay 5-12V TTL Signal 1 Channel Module High Level Expansion Board For Arduino 3Pcs 5V Relay 5-12V TTL Signal 1 Channel Module High Level Expansion Board For Arduino 3Pcs 5V Relay 5-12V TTL Signal 1 Channel Module High Level Expansion Board For Arduino

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Features: LC 5A Over-current protection Sensor module uses current transformer to collect the AC signal to achieve the relay over-current signal output within 0-5A. Relay pull while over-current, relay released while not over-current. Users can use the relay COM, NC, NO three ports to control the external circuit on and off, in order to achieve over-current protection. Functions: -Current detection resolution can change the parameter of resistance parameters; -Output over-current switching signal output; -Over-current signal setting critical point adjustable, Specifications: Operating voltage: DC12V Operating current: Operating frequency range: 20Hz ~ 400Hz Output mode: switch signal output Maximum detection wire diameter: 5.2mm Mounting hole: hole diameter is 3mm, hole distance is 52.5mm Operating environment: -40 ￢ﾄﾃ ~ +85 ￢ﾄﾃ The current detection range:AC0.3A-5A Board size: 38 * 44mm The Board Description: VCC: Operating voltage positive; GND:Operating voltage negative; NO: Normally open, the relay pulls before the NO and COM disconnect, short-circuit after the suction; COM: common, relay common interface; NC: Normally closed, the relay before the NC and COM short-circuit, pull off after. Using Instructions: By setting the potentiometer to set the overcurrent protection point, the clockwise adjustment reduces the detection current. As bellows: 1. Measured the wire through the current transformer, connect VCC and GND to DC12V power supply; 2. Adjust the potentiometer, when you hear the sound of the relay pull (can be measured with a multimeter COM and NO whether was turned on, if connected to the relay means activated), then reduce or cut off the current flowing that through the tested wire, if the relay release at this time that over-current protection point has been identified (available to multimeter COM and NC measurement whether is connected, if connected to the relay means been released); 3. When reduce or cut off the current flowing through the wire, the relay is not released, will still need to continue to adjust the potentiometer to find the over-current protection point. Package Included: 3 x 5A 12V Relay Module 3Pcs DC 12V 5A Overcurrent Protection Sensor Module AC Current Detection Relay Module Switch Output 3Pcs DC 12V 5A Overcurrent Protection Sensor Module AC Current Detection Relay Module Switch Output 3Pcs DC 12V 5A Overcurrent Protection Sensor Module AC Current Detection Relay Module Switch Output

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA 3Pcs Infrared Obstacle Avoidance Sensor For Arduino Smart Car Robot Description: The sensor module light is adaptable to the environment, the working voltage of 3.3 V to 5 V. It has a pair of infrared transmitting and receiving tube, when detecting direction meet with obstacles (reflecting surface), reflected infrared receiving by the tube. After the comparator circuit processing, green indicator will light up, at the same time the signal output interface output a digital signal (a low level signal), can be adjust the detection distance through the potentiometer knob, effective distance range 2 ~ 80 cm, easy to assemble and use. So it can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and so on many occasions. Package included: 3 x Arduino obstacle avoidance sensor 3Pcs Infrared Obstacle Avoidance Sensor For Arduino Smart Car Robot 3Pcs Infrared Obstacle Avoidance Sensor For Arduino Smart Car Robot 3Pcs Infrared Obstacle Avoidance Sensor For Arduino Smart Car Robot

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Feature: Working voltage: DC5V-36V Trigger signal source: digital high level (DC3.3V-20V), can be connected to the microcontroller IO port, PLC interface, DC power supply, etc., can connect PWM signal, support signal frequency 0-20khz Output: DC5V-36V, continuous current at room temperature 15A, power 400W, assisted cooling conditions, the maximum current up to 30A. Applications: Output can control high power equipment, motors, light bulbs, LED lights, DC motors, mini pumps, solenoid valves, etc., you can enter the PWM, control the motor speed, lamp brightness and so on. Operating temperature: -40 to 85 ° C Size: 3.4 x 1.7 x 1.2cm Package includes: 3 x MOS Trigger Switch Driver Module 3Pcs MOS Trigger Switch Driver Module FET PWM Regulator High Power Electronic Switch Control Board 3Pcs MOS Trigger Switch Driver Module FET PWM Regulator High Power Electronic Switch Control Board 3Pcs MOS Trigger Switch Driver Module FET PWM Regulator High Power Electronic Switch Control Board

Buy 3Pcs DIY White Noise Signal Generator Kit Two Way Signal Output for R110.00

Buy 3Pcs DC12 DIY ICL8038 Function Signal Generator Kit Sine Triangle Square Wave Signal for R326.00

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA 3pcs KY-026 Flame Sensor Module IR Sensor Detector For Temperature Detecting For Arduino Description: - High sensitivity IR receiver - Extremely sensitive to wave between 760-1100nm - With power supply indicator lamp and comparator output indicator lamp - AO, real-time thermister voltage signal output and high / low electric level signal output,Analog quantity output - Threshold rollover electric level output,Threshold adjusted by potentiometer Detection Angle Range: About 60 degrees Power Supply: 0-15 V DC Hole Inner Diameter: 3mm Size (L x W): 36 x 16mm Package Included: 3 x KY-026 Flame Sensor Module 3pcs KY-026 Flame Sensor Module IR Sensor Detector For Temperature Detecting For Arduino 3pcs KY-026 Flame Sensor Module IR Sensor Detector For Temperature Detecting For Arduino

Description: AM2320 digital temperature and humidity sensor is a kind of temperature and humidity complex sensor with calibrated digital signal output. The sensor includes a capacitive humidity sensing element and a high-precision integrated temperature measuring element, and is connected with a high-performance microprocessor. The product has excellent quality, ultra fast response, anti-interference ability, cost-effective and so on. AM2320 communication mode adopts single bus, standard I2C two communication methods. The two modes of communication can be freely switched, the user is free to choose, easy to use, wide range of applications. Application range: HVAC, dehumidifier, testing and testing equipment, consumer goods, automotive, automatic control, data recorder, weather station, home appliances, medical and other related humidity control, humidity measurement and control. Product highlights: Fully interchangeable, low cost, long-term stability, relative humidity and temperature measurement, long distance signal transmission, digital signal output, accurate calibration, low power consumption, single bus digital interface standard, I2C standard bus digital interface, communication mode can be free to choose. Technical parameter: Measuring range Temperature range: -40 - +80￢ﾄﾃ, humidity range: 0-99.9%RH Accuracy (25￢ﾄﾃ environment) Temperature accurate value: ±0.5￢ﾄﾃ, humidity accurate value: ±3%RH (10...90%RH) Resolving power Temperature: 0.1￢ﾄﾃ, humidity: 0.1%RH Attenuation value Temperature: 0.1￢ﾄﾃ / year, humidity: Sensor type Temperature: resistance type sensor, humidity: capacitive sensor Response time Temperature: 5s, humidity: 5s 1/e (63%) Operating temperature range: -40 - +80￢ﾄﾃ Power source: DC 3.1-5.5V Output signal: single bus /I2C signal Shell material: PC plastic Dimension: 15 x 12.1 x 4.5mm Package included: 3 x Temperature and humidity sensor