3pcs dc 7v

Description:   1. The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0V to 5V pulse. (or 0V to 3.3V pulse if you solder SJ2 closed on the EasyDriver) 2. EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. 3. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4, 6, or 8 wire stepper motors. 4. It provides much more flexibility and control over your stepper motor, when compared to older versions. The microstep select (MS1 and MS2) pins of the A3967 are broken out allowing adjustments to the microstepping resolution. The sleep and enable pins are also broken out for further control.cjmcu made.   Features:   1. MS1 and MS2 pins broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) 2. Compatible with 4, 6, and 8 wire stepper motors of any voltage 3. Adjustable current control from 150mA / phase to 750mA / phase 4. Power supply range from 7V to 30V. The higher the voltage, the higher the torque at high speeds 5. Distribution pin, not welded, this module is open source   Note:   Do not connect or disconnect a motor while the driver is energized.This will cause permanent damage to the A3967 IC. Chip data: https://www.alldatasheetcn.com/datasheet-pdf/pdf/83571/ALLEGRO/A3967.html   Package included:   3 X A3967 easy driver stepper motor driver board

3pcs 3.7V To 5V 1A 2A Boost Module DIY Power Bank Mainboard Built In 18650 Lithium Battery

3pcs 3.7V Lithium Battery Protection Board 18650 Polymer Battery Protection 6-12A 6MOS Package contains 1 X item of the smallest listed variant.

3pcs DC 3.7-7.4V 4A 200-400KV High Voltage Pulse Generator Super Arc Pulse Ignition Coil Transform

Buy 3pcs 3.7V Lithium Battery Protection Board 18650 Polymer Battery Protection 6-12A 6MOS for R190.91

Buy 3Pcs 2.7V 3000F Super Capacitor Voltage Regulator Board Super Capacitor Group Pressure Board Circ... for R439.00

Buy 3Pcs 2.7V 500F Super Capacitor Circuit Board Farad Capacitor Voltage Regulator for R219.67

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Feature: Input: DC 6V--12V (The input voltage must be higher than the output voltage by more than 1V.) Output: 5.0V (+-0.05v error), 800mA (load current cannot exceed 800ma) Specially designed two pin fixing holes, which can be directly fixed on the hole plate for expansion experiments; Input and output use 2P single-row pin header for easy connection; PCB board size: 2.5cm*1.1cm With power indicator (red) Package includes: 3 x Power supply module 3pcs DC/DC 5V AMS1117-5V 800mA Power Supply Module Voltage Regulator 3pcs DC/DC 5V AMS1117-5V 800mA Power Supply Module Voltage Regulator 3pcs DC/DC 5V AMS1117-5V 800mA Power Supply Module Voltage Regulator

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Features: LC 5A Over-current protection Sensor module uses current transformer to collect the AC signal to achieve the relay over-current signal output within 0-5A. Relay pull while over-current, relay released while not over-current. Users can use the relay COM, NC, NO three ports to control the external circuit on and off, in order to achieve over-current protection. Functions: -Current detection resolution can change the parameter of resistance parameters; -Output over-current switching signal output; -Over-current signal setting critical point adjustable, Specifications: Operating voltage: DC12V Operating current: Operating frequency range: 20Hz ~ 400Hz Output mode: switch signal output Maximum detection wire diameter: 5.2mm Mounting hole: hole diameter is 3mm, hole distance is 52.5mm Operating environment: -40 ￢ﾄﾃ ~ +85 ￢ﾄﾃ The current detection range:AC0.3A-5A Board size: 38 * 44mm The Board Description: VCC: Operating voltage positive; GND:Operating voltage negative; NO: Normally open, the relay pulls before the NO and COM disconnect, short-circuit after the suction; COM: common, relay common interface; NC: Normally closed, the relay before the NC and COM short-circuit, pull off after. Using Instructions: By setting the potentiometer to set the overcurrent protection point, the clockwise adjustment reduces the detection current. As bellows: 1. Measured the wire through the current transformer, connect VCC and GND to DC12V power supply; 2. Adjust the potentiometer, when you hear the sound of the relay pull (can be measured with a multimeter COM and NO whether was turned on, if connected to the relay means activated), then reduce or cut off the current flowing that through the tested wire, if the relay release at this time that over-current protection point has been identified (available to multimeter COM and NC measurement whether is connected, if connected to the relay means been released); 3. When reduce or cut off the current flowing through the wire, the relay is not released, will still need to continue to adjust the potentiometer to find the over-current protection point. Package Included: 3 x 5A 12V Relay Module 3Pcs DC 12V 5A Overcurrent Protection Sensor Module AC Current Detection Relay Module Switch Output 3Pcs DC 12V 5A Overcurrent Protection Sensor Module AC Current Detection Relay Module Switch Output 3Pcs DC 12V 5A Overcurrent Protection Sensor Module AC Current Detection Relay Module Switch Output

Buy 3pcs DC 3.3-13V to DC 15V Positive Negative Dual Output Power Supply DC DC St for R343.43

Buy 3Pcs DC 4.5V To DC 35V 5A 90W Mini DC Motor PWM Speed Controller Module Speed R for R175.52

Buy 3Pcs DC 5V To DC 35V 5A 90W Mini DC Motor PWM Speed Controller Module Speed Regulator Adjustable... for R219.00

Buy 3pcs DC 9V 12V 18V 24V 20W Adjustable LED Driver PWM Controller DC DC Step Down for R160.25

Buy 3Pcs DC 9V To 50V 10A Stepless Adjustable PWM DC Motor Speed Controller Module With Knob for R290.00

Buy DC 7V To 30V 150mA To 750mA A3967 Easy Driver Stepper Motor Board for R58.79