3pcs da analog digital

3Pcs Soil Hygrometer Humidity Detection Moisture Sensor For Arduino Description: This is a summary of the soil moisture sensor can be used to detect moisture, when the soil is dry, the module outputs a high level, whereas output low. Using this sensor make an automatic watering system, so that your garden plants without people to manage. Operating voltage: 3.3V~5V. Adjustable sensitivity (shown in blue digital potentiometer adjustment) Dual output mode,analog output more accurate. A fixed bolt hole for easy installation. With power indicator (red) and digital switching output indicator (green). Having LM393 comparator chip, stable. Panel PCB Dimension: 3cm x 1.5cm. Soil Probe Dimension: 6cm x 2cm. Cable Length: 21cm. VCC: 3.3V-5V. GND: GND. DO: digital output interface(0 and 1). AO: analog output interface. Instructions for Use: 1. Soil moisture module is most sensitive to the ambient humidity is generally used to detect the moisture content of the soil. 2. Module to reach the threshold value is set in the soil moisture, DO port output high, when the the soil humidity exceeds a set threshold value, the module D0 output low. 3. The digital output D0 can be connected directly with the microcontroller to detect high and low by the microcontroller to detect soil moisture. 4. The digital outputs DO shop relay module can directly drive the buzzer module, which can form a soil moisture alarm equipment. 5. Analog output AO and AD module connected through the AD converter, you can get more precise values of soil moisture. Package Included: 3 x Soil moisture detector module 3 x Probe 3 x 2P Jumper Cable

3Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module Description: You’ve always wanted to output analog voltages from a microcontroller, the MCP4725 is the DAC that will let you do it! The CJMCU-MCP4725 is an I2C controlled Digital-to-Analog converter (DAC). A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller. Digital to analog converters are great for sound generation, musical instruments, and many other creative projects! This version of the CJMCU-MCP4725 Breakout fixes a few issues with the board including the IC footprint, the I2C pinout, changes the overall board dimensions to better fit your projects, and a few more minor tweaks. This board breaks out each pin you will need to access and use the MCP4725 including GND and Signal OUT pins for connecting to an oscilloscope or any other device you need to hook up to the board. Also on board are SCL, SDA, VCC, and another GND for your basic I2C pinout. Additionally, if you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this. Feature: 12-bit resolution I2C Interface (Standard, Fast, and High-Speed supported) Small package 2.7V to 5.5V supply Internal EEPROM to store settings Package included: 3 x CJMCU-MCP4725 I2C DAC Breakout Development Board Module

3Pcs 3.3V 8MHz ATmega328P-AU Pro Mini Microcontroller Board For Arduino Description: The Pro Mini is a microcontroller board based on the ATmega328 for Arduino. With 14 digital input / output pins (of which 6 can be used as PWM outputs), 8 analog inputs, an on-board resonator, a reset button, and holes for mounting pin headers. Six pin header can be connected to an FTDI cable to provide USB power and communication to the board. Feature: Using ATmel Atmega328P-AU MCU TTL level serial port transceiver RX / TX Six PWM ports D3, D5, D6, D9, D10, D11 Supporting serial download Supporting external DC 2.4V ~ 12V power Supporting 12V (or below) battery power Specification: Microcontroller: ATmega328 Operating Voltage: 3.3V Input Voltage: 3.35V ~ 12V Digital I/O Pins: 14 (of which 6 provide PWM output) Analog Input Pins: 8 DC Current Per I/O Pin: 40mA Flash Memory: 32KB (of which 2KB used by bootloader) SRAM: 1KB EEPROM: 512bytes Clock Speed: 8MHz Size: 33.3 x 17.6mm Package included: 3 x 3.3V 8MHz Pro Mini(With Pins)

3Pcs MAX7219 Red 8 Bit Digital Tube LED Display Module For Arduino MCU Description: MAX7219 is an integrated serial input / output common-cathode display drivers, which connects the microprocessor and 8 bit 7-segment digital LED display, you can also connect a bar graph display or 64 separate LED. Includes an on-chip type B BCD encoders, multi-channel scanning loop, segment word driver, but also a 8x8 static RAM that stores each data. Only one external register is used to set the current of each LED segment. A convenient four-wire serial interface can connect all common microprocessor. Each data can be addressed in the update without rewriting all displays. MAX7219 also allows the user to select each data encoding or no coding. The entire device includes a 150μA low-power shutdown mode, analog and digital brightness control, a scan-limit register allows the user to display 1-8 bit data, there is an all LED light detection mode. Feature: 0.36 inch Common cathode Only need three IO ports can drive 8 bit digital tube The module compatible of 5V / 3.3V microcontroller (51 / AVR / STM32...) PCV board four corners of the fixed copper stud, which can effectively precent short circuit accidents happen Wiring instructions (a program, for example, you can pick any IO port definition can be modified in the program): VCC to 5V, GND to GND, DIN to P00, CLK to P02, CS to P01 Note: VCC and GND do not reversed, it would burn the chip. 51 MCU P0 port requires pull-up resistor, if your device does not have a pull-up resistor can be connected to other ports data lines. Package included: 3 x MAX7219 8 bit digital tube module 12 x Copper pillar 12 x Screws

Buy 3pcs PCF8591 AD/DA Converter Module Analog to Digital to Analog Conversion for R305.00

Description: The ML8511 breakout is an ultraviolet light sensor which is easy to use. The MP8511 UV (ultraviolet) Sensor works by outputing an analog signal in relation to the amount of UV light that's tested. This breakout can be very handy in creating devices that warn the user of sunburn or test the UV index as it relates to weather conditions. The range of the most effective light tested by the sensor is 280-390nm. This is categorized as part of the UVB (burning rays) spectrum and most of the UVA (tanning rays) spectrum. It outputs an analog voltage that is linearly related to the measured UV intensity (mW / cm2). If your microcontroller can do an analog to digital signal conversion then you can test the level of UV! ML8511 UV light can be used with an analog voltage output proportional to the amount. Since the output voltage can therefore be directly connected to the MCU built A / D digital / analog converter, no photoelectric converting circuit. And the use of small, low-profile surface-mount package, suitable for use in portable devices. Package included: 3 x GY-8511 ML8511 UVB rays sensor

Description: The D1 R2 is a mini wifi board based on ESP-8266EX. 11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supported(except D0) 1 analog input(3.3V max input) A Micro USB connection A power jack, 9-24V power input. Compatible withArduino Compatible with nodemcu Arduino NodeMcu Technical specs: Microcontroller ESP-8266EX Operating Voltage 3.3V Digital I/O Pins 11 Analog Input Pins 1 Clock Speed 80MHz/160MHz FLash 4M bytes Length 68.6mm Width 53.4mm Weight 25g Pin Function ESP-8266 Pin TX TXD TXD RX RXD RXD A0 Analog input, max 3.3V input A0 D0 IO GPIO16 D1 IO, SCL GPIO5 D2 IO, SDA GPIO4 D3 IO,Pull-up GPIO0 D4 IO,pull-up, BUILTIN_LED GPIO2 D5 IO, SCK GPIO14 D6 IO, MISO GPIO12 D7 IO, MOSI GPIO13 D8 IO,pull-down, SS GPIO15 G Gound GND 5V 5V - 3V3 3.3V 3.3V RST Reset RST

Description: BS Micro is based on the ATmeag32U4 Micro controller board. It owns 14 general purpose digital input/output pin (five can be used as a PWM output, 6 can be used as an analog input). On board with 16 MHZ crystals and A USB - type A interface based on PCB. In addition to A 3.3 V power supply output independently, it will not affect the work of MCU power output, the output power depends on the USB port power supply capacity, but is not higher than 1.5 A. Bat has burn Arduino bootloader, so it is compatible with the Arduino IDE. Although it is small in size, but it has rich interface, make it not only has the function of the traditional controller, and realize the function of the mouse, keyboard on the computer, a serial port function, and can realize communication with computer directly. It like most other MCU control board is a big difference between programming does not need additional use programmer, directly from the USB programming. This is not only convenient, stable and reliable, also save the expense of a programmer. Product features: Master: ATmega32u4 Working voltage: 5 v Digital I/o number: 14 PWM output number: 5 Analog input number: 6 Other peripherals: USB, UART, I2C, SPI, 3.3 V Power Supply Output 40 ma IO driving force: Flash: 32 KB (ATmega32u4) including 4 KB is Arduino bootloader footprint SRAM: 2.5 KB (ATmega32u4) EEPROM: 1 KB (ATmega32u4) 16 MHZ frequency: Width: 800 mils (20.3 mm) Length: 1200 mils (30.5 mm) Weight: 2.5 g (not including packaging and accessories) Package included: 3 x Wemos® ATMega32U4 BS Micro Pro Micro Leonardo

Features: 1. Using high-quality dual-panel design, with power indicator and TTL signal output instructions 2. there are four screw holes for easy positioning 3. Analog output voltage with the higher concentration of higher voltage 4. TTL output valid signal is low. (Low-level signal when the output light can be directly connected to the microcontroller or relay module) 5. The switching signal having a DO (TTL) output and analog output AO Special note: After the sensor is powered, needs wait about 20S, measured data was stable, heat sensor is a normal phenomenon, because the internal heating wire. Specifications: Size: 32 x 22 x 27mm Chip: LM393, ZYMQ-2 gas sensors Working voltage: DC 5V AO output:0.1-0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V DO output: TTL digital 0 and 1 (0.1 and 5V) Input voltage: DC 5V Power consumption (current): 150mA Package included: 3 x MQ-2 gas sensor module

Features: - Sensitive material MQ-9 gas sensor is used to clean the air in the lower conductivity of tin dioxide (SnO2). - Detection method using low temperature cycling (1.5V heating) to detect carbon monoxide, conductivity sensors with carbon monoxide in the air increased with increasing gas concentration, spurious adsorption at high temperatures (5.0V heating) detection of combustible gases methane, propane and cryogenic cleaning gases. - Simple circuit can be used to change the conductivity, concentration of the gas is converted to the corresponding output signal. - MQ-9 high gas sensor for carbon monoxide, methane, liquefied petroleum gas sensitivity, the sensor can detect a variety of gases containing carbon monoxide and flammable, is a low-cost sensors for a variety of applications. Speciffications: 1. It adopts high quality double panel design with power indication and TTL signal output indication; 2. It has DO switch signal (TTL) output and AO analog signal output; 3. The TTL output valid signal is low. (When the output is low, the signal light is on, it can be directly connected to the MCU or relay module) 4. The voltage of the analog output, the higher the concentration, the higher the voltage. 5. It has good sensitivity to gas and natural gas detection. 6, there are four screw holes for easy positioning; 7, product dimensions: 32 (L) * 20 (W) * 22 (H) 8, has a long life and reliable stability 9, fast response recovery characteristics Electrical Performance: Dection of gas: Carbon monoxide flammable gas Dection of Concentration:10-1000ppm(CO);100-10000(Gas) ppm Input voltage: DC5V Power consumption (current): 150mA DO output: TTL digital quantities 0 and 1 (0.1 and 5V) AO output: 0.1-0.3V (relatively non-polluting), the highest concentration voltage is about 4V Using the chip: AT89S52 Crystal: 11.0592MHZ Baud rate: 9600 Compilation environment: Keil Special Reminder: After the sensor is energized, it needs to be preheated for about 20S, and the measured data is stable. The heating of the sensor is a normal phenomenon, because there is a heating wire inside, if it is hot, it is not normal. Package Included: 3 x MQ-9 Gas Sensor Module

Description: This is the old version of WeMos D1. 11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supported(except D0) 1 analog input(3.3V max input) A Micro USB connection A power jack, 9-24V power input. Compatible with Arduino Compatible with nodemcu Infos: click here!! Package included: 3 x WeMos D1 WiFi UNO ESP-12E Based ESP8266 Shield For Arduino Compatible

Description: This Nano Mult-Function expansion board is designed specially for Arduino Nano, solve the problem of wiring confusing when a variety of sensors connected. Lead out all digital IO port and analog IO port, each one with standard positive and negative power interface. Lead out the I2C interface of mainboard for convenient connection. Increasing the DC power supply interface. Nano USB interface supply current is actually only 50MA, to bring high-current devices, such as the steering, is obviously insufficient. So in the DC power connector provide external power supply to ensure the stability of equipment operation. Package included: 3 x Nano shield

Buy PCF8591 AD DA Converter Module Analog to Digital to Analog Conversion... for R169.00

Buy 5pcs PCF8591 AD/DA Converter Module Analog to Digital to Analog Conversion for R410.00

Buy 5pcs PCF8591 AD/DA Converter Module Analog to Digital to Analog Conversion... for R399.00