3pcs avr mcu

Buy 3pcs AVR MCU Minimum Learning System Development Board ATMEGA16A-PU/32A-PU Mega16 for R310.00

Buy AVR MCU Minimum Learning System Development Board ATMEGA16A-PU/32A-PU Mega16 for R132.49

DEVELOPMENT BOARD FOR 8 PIN AVR MICROCONTROLLERS WITH ON BOARD RS232; CRYSTAL; ICSP AND VOLTAGE REGULATOR

3Pcs MAX7219 Red 8 Bit Digital Tube LED Display Module For Arduino MCU Description: MAX7219 is an integrated serial input / output common-cathode display drivers, which connects the microprocessor and 8 bit 7-segment digital LED display, you can also connect a bar graph display or 64 separate LED. Includes an on-chip type B BCD encoders, multi-channel scanning loop, segment word driver, but also a 8x8 static RAM that stores each data. Only one external register is used to set the current of each LED segment. A convenient four-wire serial interface can connect all common microprocessor. Each data can be addressed in the update without rewriting all displays. MAX7219 also allows the user to select each data encoding or no coding. The entire device includes a 150μA low-power shutdown mode, analog and digital brightness control, a scan-limit register allows the user to display 1-8 bit data, there is an all LED light detection mode. Feature: 0.36 inch Common cathode Only need three IO ports can drive 8 bit digital tube The module compatible of 5V / 3.3V microcontroller (51 / AVR / STM32...) PCV board four corners of the fixed copper stud, which can effectively precent short circuit accidents happen Wiring instructions (a program, for example, you can pick any IO port definition can be modified in the program): VCC to 5V, GND to GND, DIN to P00, CLK to P02, CS to P01 Note: VCC and GND do not reversed, it would burn the chip. 51 MCU P0 port requires pull-up resistor, if your device does not have a pull-up resistor can be connected to other ports data lines. Package included: 3 x MAX7219 8 bit digital tube module 12 x Copper pillar 12 x Screws

3Pcs TM1638 Chip Key Display Module 8 Bits Digital LED Tube For AVR Arduino Features:8 Bits, 8 keys, 8 LEDs, 8 digital tubes, common cathode LED digital tube.With TM1638 Chip, this module gather more than three common SCM peripheral circuits.The advantage is only three IO ports will be occupied when it drives.SCM doesn't need to work for scaning display and key scaning.It only need to read the relevant register to send display data or test button so it save MCU resources effectively.Keys are sensitive and display effectively.Specification:Weight: 28gMaterial: Glass fiber reinforced plastic, PBT shell, PA bladesHow to connect: VCC GND 5V power supply, STB CLK DIO SCM IO port.Package included:3 x LED display module withe cable

3pcs 3.3V / 5V USBASP USBISP AVR Programmer Downloader ATMEGA8 ATMEGA128 With Download Cablec Description:1. The onboard ATMega8 chip (L)2. The onboard over - current protection3. The target board support 5 V and 3.3 V power supplyPackage included:3 x USBASP USBISP AVR downloader with download cable

3Pcs ATTINY85 Mini Usb MCU Development Board For Arduino Feature: 8K Byte of In-System Programmable Program Memory Flash 512 Bytes In-System Programmable EEPROM 512 Bytes Internal SRAM 1.8-5.5V work voltage Support SPI/TWI communication Low power consumption Package included: 3 x ATTINY85 Mini Usb MCU Development Board For Arduino

3Pcs MAX7219 Dot Matrix Module MCU LED Control Module Kit For Arduino Specifications: A single module can drive an 8 x 8 common cathode lattice Operating voltage: 5V Size: 5 x 3.2 x 1.5 cm (L x W x H) LED color: Red With four screws hole, aperture 3mm With input and output interfaces, supports multiple modules cascade Wiring instructions: 1. The module left side as an input port and the output port on the right 2. To control a single module, just connect the input port to the CPU 3. When cascading multiple modules, the input port of the first module connect to the CPU, the output port connect to the input port of the second one, and so on. In the case of 51 MCU: VCC → 5V GND → GND DIN → P22 CS → P21 CLK → P20 Note: 1. VCC and GND is not reversed, it would burn the chip! 2. When the 51 microcontroller P0 port controlling, must be connected to the pull-up resistor, it is recommended that the resistance of 4.7K--10K 3. Please install lattice into the round hole first, and then insert the round hole to PCB board and weld. Face the side of lattice with words, from left to right pin order is 123456. PCB board 1st pin is square pad! 4. Electrolytic capacitors long-pin as positive, short-pin as negative; ceramic capacitor hsa no positive and negative points Package included: 3 x LED module 3 x Dupont line (5P-20cm)

3Pcs I2C RTC DS1307 AT24C32 Real Time Clock Module For AVR ARM PIC SMD Package contains 1 X item of the smallest listed variant.

3Pcs 3 Colour RGB SMD LED Module 5050 Full Color Pwm For Arduino MCU

3Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 3 x Micro SD TF card module

3Pcs 3.3V 8MHz ATmega328P-AU Pro Mini Microcontroller Board For Arduino Description: The Pro Mini is a microcontroller board based on the ATmega328 for Arduino. With 14 digital input / output pins (of which 6 can be used as PWM outputs), 8 analog inputs, an on-board resonator, a reset button, and holes for mounting pin headers. Six pin header can be connected to an FTDI cable to provide USB power and communication to the board. Feature: Using ATmel Atmega328P-AU MCU TTL level serial port transceiver RX / TX Six PWM ports D3, D5, D6, D9, D10, D11 Supporting serial download Supporting external DC 2.4V ~ 12V power Supporting 12V (or below) battery power Specification: Microcontroller: ATmega328 Operating Voltage: 3.3V Input Voltage: 3.35V ~ 12V Digital I/O Pins: 14 (of which 6 provide PWM output) Analog Input Pins: 8 DC Current Per I/O Pin: 40mA Flash Memory: 32KB (of which 2KB used by bootloader) SRAM: 1KB EEPROM: 512bytes Clock Speed: 8MHz Size: 33.3 x 17.6mm Package included: 3 x 3.3V 8MHz Pro Mini(With Pins)

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA 3Pcs 3 Colour RGB SMD LED Module 5050 Full Color Pwm For Arduino MCU 3Pcs 3 Colour RGB SMD LED Module 5050 Full Color Pwm For Arduino MCU Description: RGB tricolor access the current limiting resistor to prevent burn out. The PWM modulator with three primary colors can be mixed in different colors. With a variety of microcontroller interface. Based on the arduino simple test program. Size: 20 x 10 x 7mm (Lx Wx H) Package included: 3 x 3 Colour LED Module 3Pcs 3 Colour RGB SMD LED Module 5050 Full Color Pwm For Arduino MCU 3Pcs 3 Colour RGB SMD LED Module 5050 Full Color Pwm For Arduino MCU

Description: Note: This module does not suitable for IOS system. The core module HC-06 main modules, leads the interface includes VCC, GND, TXD, RXD, KEY pin high trigger to clear the pairing information re search led indicate Bluetooth connection status, flash unpaired slow flash indicates paired but not slave connection, Always follow machine connected Backplate settings LDO input voltage of 3.6~~6V unpaired current is about 30mA, paired 10mA, input voltage prohibit more than 7V absolute prohibition of reverse power! Interface level 3.3V, can be directly connected the various SCM (51, AVR, PIC, ARM, MSP430, etc.), the 5V MCU also can be connected directly, without MAX232 can not go through the MAX232! Open to effective distance of 10 meters, over 10 meters is also possible, but not of this the quality of the connection of the distance do to ensure The pair later when full-duplex serial use, do not need to know anything about the Bluetooth protocol, but only supports 8 data bits, 1 stop bit, no parity communication format, which is the most commonly used communication format does not support other formats. Support to establish a Bluetooth connection through AT commands set the baud rate, passkey, set parameters are saved after. Bluetooth connection is automatically switched to the pass-through mode. Wireless serial Bluetooth port with free extension cable. With transparent shrink tube, dust and beautiful, and there is a certain degree of anti-static capabilities. Size:3.57cm x 1.52cm Tips: TXD: the sender, usually expressed as its sender, the normal communication must be connected to another device RXD. RXD: the receive side, generally expressed as the receiving end of their normal communication to another device connected to TXD. Package included: 3 x HC-06 wireless bluetooth transceiver

Description: With this USBTinyISP programmer you can upload sketches and burn the bootloader on any AVR based boards, including Arduinos. By uploading a sketch with an external programmer you can remove the bootloader and use the extra space for your sketch. This Programmer can also be used to burn the Arduino bootloader, so you can recover your chip if you accidentally corrupt the bootloader. Burning the bootloader is also necessary when you use a new ATmega microcontroller in your Arduino, and you wish to use the bootloader to upload a sketch via the USB-Serial connection. Package included: 3 x AVR ISP ATtiny44 USBTinyISP Programmer Arduino Bootloader