3pcs 5v

3Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load: AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 3 x 1 Channel H/L level trigger optocoupler relay module

3Pcs 5V IIC I2C Serial Interface Adapter Module For Arduino LCD1602 Description: The item is IIC/I2C serial interface Compatible for 1602 LCD Supply voltage: 5V Package included: 3 x IIC I2C Serial Interface Adapter

3pcs 5V 3.3V FT232RL USB Module To Serial 232 Adapter Download Cable For Arduino Feature: 1. With FT232RL chipset, support 3.3V, 5V 2. With over current protection, using 500MA self-restore fuse 3. RXD/TXD transceiver communication indicator 4. Pin definition: DTR,RXD,TX,VCC,CTS,GND Package included: 3 x USB Module

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: Trigger mode: High level 5V relay module Can be used for microcontroller development board module or home appliance control 5V - 12V TTL control signal Can control DC or AC signal, also 220V AC load Normally open / closed contact Power indicator Controlled lights bright when pull and not shine when disconnect Increase the transistor drive relay coils, control pins high impedance Control pins have pull down circuit to prevent malfunction of relay vacant Package included: 3 x 5V 1 channel relay module 3Pcs 5V Relay 5-12V TTL Signal 1 Channel Module High Level Expansion Board For Arduino 3Pcs 5V Relay 5-12V TTL Signal 1 Channel Module High Level Expansion Board For Arduino 3Pcs 5V Relay 5-12V TTL Signal 1 Channel Module High Level Expansion Board For Arduino

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA New toy for makers who want to build their own smart home system Overview: The wireless switch supports inching /self-locking mode. You can add the device to the APP eWeLink to remote control connected home appliances or devices. In self-locking mode, you can remote turn on/off connected devices immediately. When in inching mode, you have two wiring ways to select, whether turn on 1s and then auto-off or turn off 1s and then auto-on. Remote control by APP EweLink for iOS and Android. Supported functions include remote on/off, timing schedules, device sharing, group management. The self-lock/inching mode wireless switch has two power supply specification: 5V. No matter which specification you select, they have the same functions. Feature: There are two working modes for the module: inching mode and self-locking mode. Press the self-lock/inching mode button to switch between these two modes. When your module is switched to self-locking mode, you can turn on/off the connected appliance instantly. There is two wiring way. When your module is switched to inching mode, you can press on/off toggle button to turn on or off connected device. There are two kinds of wiring way. The first wiring way is to connect COM and NO with an appliance. In this way, when you press the setting button or APP to turn on, the connected appliance will be turned on for 1s and then auto turned off. The second wiring way is to connect NC and COM with an appliance. In this way, when you press the setting button or APP to turn off, the connected appliance will be turned off for 1s and then auto turned on. LED Indicator: There are 3 LEDs, the led beside self-lock/inching mode button indicates the working mode(on: self-locking mode, off: inching mode). The one beside on/off setting button indicates wifi status(enter pairing status: long press the setting button until led fast blink). Another one below the relay indicates relay on or off status(on: turn on the connected device, off: turn off connected device). Add device to eWeLink: Long press the setting button until the LED beside on/off setting button fast blinking. 1. Android: Add Device->select pairing method according to how the LED blinks->enter WiFi name and password->pairing and register->name device 2. iOS: go to phone setting->WiFi-> select the WiFi starts with ITEAD-********, enter default password to connect:12345678-> go to eWeLink->Add device->->select pairing method according how the LED blinks->enter WiFi name and password->pairing and register->name device Specification: Dimension:70.5mm*27.4mm*23mm Operating current: 5V DC Leds: indicate working mode, wifi status, relay on/off status. Two input interface Board consumption: Standby current: 80mA Max input current: 10A Support to control different voltage range Relay lifespan: more than one million times 100M electrical insulation resistance Electric shock voltage: 1000V Relay maximum pull time: 15ms Relay maximum release time: 5ms Operating temperature: -40 degrees to +70 degrees Operating Humidity 40% ~ 80% RH Application: The switch can be applied to access control, turn on PC, garage door, etc. Package includes: 3 x Module 3pcs 5V WiFi Remote Garage Door Opener Controller Work with Alexa & IFTTT Google home Wireless Remote Control Switch 3pcs 5V WiFi Remote Garage Door Opener Controller Work with Alexa & IFTTT Google home Wireless Remote Control Switch 3pcs 5V WiFi Remote Garage Door Opener Controller Work with Alexa & IFTTT Google home Wireless Remote Control Switch

Buy 3pcs 5V Breathing Light Kits DIY LED Flash Kit Blue Flashing Lamp Electronic Se for R161.17

Buy 3Pcs 5V 2 Channel Level Trigger Optocoupler Relay Module for R195.00

Buy 3pcs 5V/3.3V Speed Measurement Hall Sensor Module Hall Switch Motor Tachometer Module For DIY for R210.00

Buy 3pcs 5V To 24V 4 Channel Optocoupler Isolation Board Isolated Module PLC Signal Level Voltage Con... for R419.00

Buy 3pcs 5V Mono Stereo Bluetooth Receiver Audio Module Output Universal for R190.91

Buy 3pcs 5V 3.3V Burning Programmer Automatic STC Download Cable USB To TTL USB To for R349.00

Buy 3pcs 5V 1A Wireless Power Supply Charging Module 5W Wireless Charger Transmitte for R279.00

Buy 3pcs 5V 4 Channel Relay Module For PIC ARM DSP AVR MSP430 Blue Geekcreit fo for R269.00

Buy 3pcs 5V Mini USB Power Connector DC Power Socket Board for R219.67

Buy 3pcs 5V 1A Wireless Power Supply Charging Module 5W Wireless Charger Transmitter Quick Charger DIY M for R284.00

Buy 3pcs 5V 2A Solar Panel Power Bank USB Charge Voltage Controller Regulator Module 6V 20V Input for R290.00

Description: Trigger mode: High level 5V relay module Can be used for microcontroller development board module or home appliance control 5V - 12V TTL control signal Can control DC or AC signal, also 220V AC load Normally open / closed contact Power indicator Controlled lights bright when pull and not shine when disconnect Increase the transistor drive relay coils, control pins high impedance Control pins have pull down circuit to prevent malfunction of relay vacant Package included: 3 x 5V 1 channel relay module

3Pcs 8-Channel Logic Level Translator Converter Bi-Directional Module 3Pcs 8-Channel Logic Level Translator Converter Bi-Directional ModuleIntroduction:If you've ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be.The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time.This level converter also works with 2.8V and 1.8V devices.What really separates this Logic level converter from our previous versions is that you can successfully set your high and low voltages and step up and down between them safely on the same channel.Each level converter has the capability of converting 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side.The level converter is very easy to use.The board needs to be powered from the two voltages sources (high voltage and low voltage) that your system is using.High voltage (5V for example) to the 'HV' pin, low voltage (3.3V for example) to 'LV', and ground from the system to the 'GND' pin.Feature:8-channel high-voltage and low-voltage logic bidirectional translationMini size, 4.1cm x 1.8cmComes with 2 rows of 6pin, unsolderedCompatible breadboard, can be directly inserted in the breadboardNote: (For example: High voltage: 5V, low voltage: 3.3V)HV connect 5V power supplyLV connect 3.3V power supplyGND connect negative, two power supply commonsLVx input and output is 3.3V TTL, HVx input and output is 5V TTL, LVx and TVx bidirectional transfersPackage includes:3 x Eight Channel Logic Level Translator Converter

3Pcs 3V To 5V 1A USB Charger DC-DC Converter Step Up Boost Module Features: Module uses the Taiwan production boost chip, high efficiency (up to 92%), plus built-in over-current protection chip, can be more good to protect the module and use the device after the class. Module with undervoltage protection, undervoltage protection into state below 2.5V, can be more better protect the battery, to avoid excessive discharge. Module can modify the fixed resistor adjusts the output voltage can be adjusted up to 12V output, but to ensure that the output power of less than 5W. This module uses TDK multilayer ceramic capacitors as main filter capacitor, the output ripple can be as low as 20mV (5V1A output case)! This module uses a standard USB interface, you can use all universal USB charging mobile phones, MP3, MP4 and other equipment, the perfect support for IPHONE and other mobile phone. Specification: Module properties: Non-isolated step-up module (BOOST) Input voltage: 2.5-6V Output voltage: 4-12 V(Adjustable, the default 5 v) Output current: 1000mA (Max) Efficiency: 92%(Max) (the higher the input voltage, the higher the efficiency) Switching frequency: 1MHz Output ripple: 20mV (MAX) Operating temperature: Industrial (-40°c to +85°c) Voltage regulation: ±2.5% Short circuit protection: None (please use the lithium battery with protection) Input: IN + postive, IN - negative Output: USB output Size: 3 x 1.3 x 0.8 cm Application: This module can be used for DIY mobile power output, enabling single or two ordinary lithium battery to 5V boost to the mobile phone or PSP device charging. DIY a mobile power supply, only need one battery, you can output 5V voltage for your phone, MP3, MP4, PSP charger, very easy. In order to power your electronic devices when your device needs 5V power supply, when you only have lithium battery, this module can be directly step-up to 5V, solve your problems. Note: This module is a fixed 5V output module Modules indicated above IN - (negative input), IN + (positive input), OUT-(negative output), OUT + (positive output) must be connected correctly, otherwise it may cause damage to the module This module has an LED light, when the charge when the LED lights can be used as indicator Package included: 3 x USB boost module

3Pcs 1.5V 1.8V 2.5V 3V 3.3V 3.7V 4.2V To 5V DC-DC Boost Converter Module Board Package contains 1 X item of the smallest listed variant.

3Pcs DC-DC 1V-5V To 5V 500mA Boost Converter Step Up Power Module Feature: Input voltage of DC 1V~5V, output 5V DC voltage is stable, the input to the output current of 500~600MA with two AA batteries, a single AA battery power supply output current 200 ma about for mobile phones camera, single-chip, digital products. High conversion efficiency up to 96% Ultra-small size, installed in a variety of small equipment With working lights Specification: Input voltage: DC 1V~5V Output voltage: DC 5V Output Current: 500mA PCB size: 17.55mm*25.22mm*5.85 mm En bloc Size: 17.55*32.53*8.3mm Weight: 14g Note: No USB port. Package included: 3 x Boost Converter Power Module

3Pcs 8-Channel Logic Level Translator Converter Bi-Directional Module Introduction: If you've ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. This level converter also works with 2.8V and 1.8V devices. What really separates this Logic level converter from our previous versions is that you can successfully set your high and low voltages and step up and down between them safely on the same channel. Each level converter has the capability of converting 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side. The level converter is very easy to use. The board needs to be powered from the two voltages sources (high voltage and low voltage) that your system is using. High voltage (5V for example) to the 'HV' pin, low voltage (3.3V for example) to 'LV', and ground from the system to the 'GND' pin. Feature: 8-channel high-voltage and low-voltage logic bidirectional translation Mini size, 4.1cm x 1.8cm Comes with 2 rows of 6pin, unsoldered Compatible breadboard, can be directly inserted in the breadboard Note: (For example: High voltage: 5V, low voltage: 3.3V) HV connect 5V power supply LV connect 3.3V power supply GND connect negative, two power supply commons LVx input and output is 3.3V TTL, HVx input and output is 5V TTL, LVx and TVx bidirectional transfers Package includes: 3 x Eight Channel Logic Level Translator Converter

3Pcs ATMEGA328 328p 5V 16MHz Arduino-Compatible Nano Size Module Board Description: New version, Pro Mini 328 5V 16MHz, arduino-compatible High Quality components and soldering material Bootloader Ready, plug and play. Package included: 3 x Pro Mini 328 5V 16MHz arduino-compatible Notice from customer Mattias Schlenker: If uploading sketches using the Arduino IDE fails, follow these steps to update the bootloader: -Prepare an Arduino Uno, Mega or similar to act as ISP as described at http://arduino.cc/en/Tutorial/ArduinoISP -Wire it up as shown in flasbootloader_connected.png (Picture Reveiw of SKU099688) -Use Arduino IDE to flash the bootloader of the corresponding Pro/Pro Mini (5V, 16MHz) to SKU099688 or SKU066315

3pcs CJMCU 5V Mini USB Power Connector DC Power Socket Board For Arduino Features:Mini USB interface: input 5V, output 5V and 3.3VDC power socket interface: input 5-12V, output (5V label) 5V-12V and 3.3V.Size: 25mm * 25mmPackage included:3 x Mini USB Power Connector DC Power Socket Board

3pcs Pro Micro 5V 16M Mini Leonardo Microcontroller Development Board For Arduino Description: This microcontroller development board has 4 channel 10 bit ADC, 5 PWM pins, 12 DIO, and a hardware serial connection Rx and Tx you are familiar with. Running on 16MHz and 5V, this board will remind you a lot of other Arduino compatible boards that you like. There is a voltage regulator on board, so it can accept up to 12V DC. If you are supplying an unstable power supply board, be sure to connect to the "RAW" not on the VCC pin. We have also added a PTC fuse and diode protection to the power circuit and to correct the RX and LED TX circuits. Feature: - ATMEGA32U4 running in 5V / 16MHz - Support Arduino IDE V1.0.1 - Micro USB interface programming on the board - Four 10-bit ADC pin - 12 digital I / O (5 PWM capability) - Rx and Tx hardware serial connection Package included: 3 x Mini Leonardo Microcontroller Development Board

3Pcs Two Channel IIC I2C Logic Level Converter Bi-Directional Module Feature: Power supply:5V-3V AVCC connect to 5V system power ASCL connect to 5V system SCL ASDA connect to 5V system SDA AGND connect to 5V system GND BVCC connect to 3V system power BSCL connect to 3V system SCL BSDA connect to 3V systems SDA BGND connect to 3V system GND Package included: 3 x Two Channel IIC I2C Logic Level Converter Bi-Directional Module

3Pcs IIC/I2C/TWI/SP Serial Interface Module Port For 5V Arduino 1602LCD Display Description: This is another great IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display via only 2 wires. If you already has I2C devices in your project, this LCD module actually cost no more resources at all. It is fantastic for Arduino based project. I2C Address: 0X20~0X27 (the original address is 0X20,you can change it yourself) the backlight and contrast is adjusted by potentiometer Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable I2C Address: 0x27 (I2C Address: 0X20~0X27 (the original address is 0X27,you can change it yourself) Specification: Compatible for 1602 LCD Supply voltage: 5V Weight: 5g Size: 5.5x2.3x1.4cm Package included: 3 x IIC/I2C/TWI/SPI serial interface module port

3Pcs FTDI Basic Program Downloader USB-TTL 3.3 / 5V FT232 For Arduino Features: 1. Standard interface, compatible with a variety of official Arduino controller 2. Original FT232 chip, stable performance 3. With indicator indicates power, sending and receiving, the working status can be seen clearly 4. 3.3V / 5V (Optional) 5. Can be used as an ordinary USB to serial TTL module and download STC microcontroller 6. Size: 4.5 x 1.8 x 0.6cm (L x W x H) 7. Mini USB Cable length: 25cm / 9.8inch Driver download: http: //www.ftdichip.com/Drivers/VCP.htm Direct Download (for x86): http: //www.ftdichip.com/Drivers/CDM/CDM20802%20WHQL%20Certified.zip Package included: 3 x FTDI Basic Program Downloader USB-TTL 3 x USB2.0 to Mini USB Cable

3Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 3 x Micro SD TF card module

3pcs 3.3V / 5V USBASP USBISP AVR Programmer Downloader ATMEGA8 ATMEGA128 With Download Cablec Description:1. The onboard ATMega8 chip (L)2. The onboard over - current protection3. The target board support 5 V and 3.3 V power supplyPackage included:3 x USBASP USBISP AVR downloader with download cable