3pcs 1ch dc 12v

Buy 3Pcs Geekcreit DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Swi for R369.00

Buy 3Pcs Geekcreit DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch for R415.57

Buy 3Pcs Geekcreit DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Transmitter With Rec for R416.00

Buy 3Pcs W3231 DC 12V LED Digital Thermostat Temperature Controller Regulator Heati for R323.17

Buy 3pcs XD-M131 DC 12V Photosensitive Resistor Module Light Control Switch Photose for R279.00

Buy 3pcs AC/DC 12V Fish Tank Aquarium Automatic Water Supply Controller Water Level for R419.00

Buy 3pcs XH-W1209 DC 12V Thermostat Temperature Control Switch Thermometer Controller With Digital LED D for R344.00

Buy 3Pcs 10M DC 12V Power Extension Cable Cord 5.5x2.1mm Plug Wire for CCTV Camera for R465.00

Features: Easy to install and easy to carry With a slidable cover on the remote control With a hook on the remote control Use Learning coding, stable and reliable The wireless signal can pass through walls, floors and doors You can turn on or turn off the receiver with transmitter (remote control) from any place within a reliable distance Operating Voltage: DC12V Maximum Load: 10A Operating Frequency: 433MHZ (in set) Receiver Sensitivity: -100dBm Encoding Type: learning code Board Size: Approx. 5.3x3.1cm/ 2.09x1.22" Output Working Way: 1. Jog: Pressing one button is working. Loosing your finger on the same button is stop. (need one channel switch and one buttons remote control) 2. Self-lock: Pressing one button for one time is working. Pressing the same button again is stop (need one channel switch and one buttons remote control) 3. Inter-lock: Pressing one button is working. Pressing another button is stop (need one channel switch and 2 buttons remote control) 4. Please notice that here is 1CH and 1 button wireless remote control. You can choose the self-lock or jog working/ output way, you better choose jog or self-lock, so pressing the button is open, and pressing again is close, or pressing is open, and loosing finger is close Learning and Remove Method: 1. Press the learning code. The indicator from on to off, loosen your finger, press any button of the remote control, the indicator flash 2 times and off. It mean you learn it successfully 2. It can learn more than 12 PCS 2262 or 1527 chip with the different code wireless remote control 3. Remove/ Clean: Press the learning button about 8 seconds, the indicator turn on to off, it means the information that you keep have been removed successfully Package Included: 3 x Learning Code Receiver 3 x Remote Control

Buy 3pcs 1CH Channel DC 12V 60-70MA Self-locking Relay Module Trigger Latch Relay Module Bistable for R260.00

Buy 3pcs 1CH Channel DC 12V 60-70MA Self-locking Relay Module Trigger Latch Relay M for R266.55

Buy 3pcs DC 12V 1CH Channel 433MHz Relay Wireless Remote Control Switch Transmitter for R168.32

Buy 3pcs DC 12V 1CH Channel 315MHz Wireless Remote Control Switch Transmitter for R256.00

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Features: LC 5A Over-current protection Sensor module uses current transformer to collect the AC signal to achieve the relay over-current signal output within 0-5A. Relay pull while over-current, relay released while not over-current. Users can use the relay COM, NC, NO three ports to control the external circuit on and off, in order to achieve over-current protection. Functions: -Current detection resolution can change the parameter of resistance parameters; -Output over-current switching signal output; -Over-current signal setting critical point adjustable, Specifications: Operating voltage: DC12V Operating current: Operating frequency range: 20Hz ~ 400Hz Output mode: switch signal output Maximum detection wire diameter: 5.2mm Mounting hole: hole diameter is 3mm, hole distance is 52.5mm Operating environment: -40 ￢ﾄﾃ ~ +85 ￢ﾄﾃ The current detection range:AC0.3A-5A Board size: 38 * 44mm The Board Description: VCC: Operating voltage positive; GND:Operating voltage negative; NO: Normally open, the relay pulls before the NO and COM disconnect, short-circuit after the suction; COM: common, relay common interface; NC: Normally closed, the relay before the NC and COM short-circuit, pull off after. Using Instructions: By setting the potentiometer to set the overcurrent protection point, the clockwise adjustment reduces the detection current. As bellows: 1. Measured the wire through the current transformer, connect VCC and GND to DC12V power supply; 2. Adjust the potentiometer, when you hear the sound of the relay pull (can be measured with a multimeter COM and NO whether was turned on, if connected to the relay means activated), then reduce or cut off the current flowing that through the tested wire, if the relay release at this time that over-current protection point has been identified (available to multimeter COM and NC measurement whether is connected, if connected to the relay means been released); 3. When reduce or cut off the current flowing through the wire, the relay is not released, will still need to continue to adjust the potentiometer to find the over-current protection point. Package Included: 3 x 5A 12V Relay Module 3Pcs DC 12V 5A Overcurrent Protection Sensor Module AC Current Detection Relay Module Switch Output 3Pcs DC 12V 5A Overcurrent Protection Sensor Module AC Current Detection Relay Module Switch Output 3Pcs DC 12V 5A Overcurrent Protection Sensor Module AC Current Detection Relay Module Switch Output

Buy DC 12V 1CH Channel 433MHz Relay Wireless Remote Control Switch Transmitter... for R149.00