30v

30V SMD FAST SWITCHING P-CHANNEL FIELD EFFECT TRANSISTOR; Rds ON= 0.60E; WITH LOGIC GATE DRIVE

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: 1. The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0V to 5V pulse. (or 0V to 3.3V pulse if you solder SJ2 closed on the EasyDriver) 2. EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. 3. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4, 6, or 8 wire stepper motors. 4. It provides much more flexibility and control over your stepper motor, when compared to older versions. The microstep select (MS1 and MS2) pins of the A3967 are broken out allowing adjustments to the microstepping resolution. The sleep and enable pins are also broken out for further control.cjmcu made. Features: 1. MS1 and MS2 pins broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) 2. Compatible with 4, 6, and 8 wire stepper motors of any voltage 3. Adjustable current control from 150mA / phase to 750mA / phase 4. Power supply range from 7V to 30V. The higher the voltage, the higher the torque at high speeds 5. Distribution pin, not welded, this module is open source Note: Do not connect or disconnect a motor while the driver is energized.This will cause permanent damage to the A3967 IC. Chip data: https://www.alldatasheetcn.com/datasheet-pdf/pdf/83571/ALLEGRO/A3967.html Package included: 5 X A3967 easy driver stepper motor driver board 5pcs DC 7V To 30V 150mA To 750mA A3967 Easy Driver Stepper Motor Driver Board For Arduino 5pcs DC 7V To 30V 150mA To 750mA A3967 Easy Driver Stepper Motor Driver Board For Arduino 5pcs DC 7V To 30V 150mA To 750mA A3967 Easy Driver Stepper Motor Driver Board For Arduino

IRLB8721 N-Channel Power MOSFET 30V 62A TO-220   These TO-220 N-channel MOSFETs are ideal to switch high loads. Capable of switching up to 62A at 30V and the TO-220 package means that they also fit nicely in to standard 2.54mm pitch breadboard. Is is also very easy to attach a heat sink due to built in heatsink mounting hole but because of the very low Rds(on) pretty high loads can be switched without a heatsink (depends on Vgs). The TO-220 package can dissipate up to 2 Watts without a heat sink in room temperature. IRLB8721PBF N-channel MOSFET is ideal to switch high loads directly from micro controller running on 2.8V, 3.3V or 5V logic because of the low threshold voltage of less than 2.5V. Type: N-channel MOSFET Package: TO-220 Vds: 30V MAX Max current: 62A Vgs: 2.35V MAX Rds(on): as low as 8.7 milliohm (depending on Vgs) This item is available in stock and is not drop shipped. This avoids delays, customs charges and extra VAT.  

Description: Supply: 220V EU Plug /AU 220V Plug / 110V US Plug DPS-305BF 30V 5A DC Digital Control Laboratory Adjustable Power Supply for Laptop Repair DPS series digital input adjustable DC power supply is designed for laboratory, school, production lines and electronic repair designed for use. Voltage stability is high, small ripple factor, has improved the short circuit protection and overcurrent protection. Due to the voltage value is a digital keyboard input, shorten the voltage setting time, completely overcome the traditional potentiometer adjustment poor contact caused by voltage instability phenomenon. The internal power supply containing electronic switch, can conveniently open the output load. DPS305BM/BF have the same function, but different current precision. DPS305CM/CF have the same function, but different current precision. DPS305CM/CF have BM/BF all functions,  in addition they have the storage and combination lock function. DPS - 305 BM/CM: Four digit current display measuring accuracy: 0000-0.450A, ±0.001 A                                                                                                                              0.450-5 A, ±0.01 A DPS - 305 BF/CF: Five digit current display measuring accuracy: 00000-0.0450A, ±0.0001A                                                                                                                          0.0450-0.450A, ± 0.001A                                                                                                                          0.450-5 A, ±0.01 A DPS-305BM in SKU144061     DPS-305BF in SKU144068 DPS-305CM in SKU144065    DPS-305CF in SKU144070 Specification: 1, rated working conditions and dimensions Power supply voltage 220V + 10%50 / 60Hz Working conditions: 0-40 temperature relative humidity 80% Storage temperature: - 10-70 C 70% relative humidity Dimensions: 265 x 128 x 150mm (D * W * H) 2, regulated state parameters The voltage output from 0 to 30V can be continuously adjusted (to distinguish the value of 0.1V) The precision of output voltage: + 0.1V Voltage stability: Load stability: Recovery time: 100uS Ripple noise voltage: Temperature coefficient: 3, a constant current state parameters Constant current value: 305 CM 5A Ma constant current maximum 500 mA 303CM 3A Ma constant current maximum 500 mA Constant current output current from 0 to the nominal value of continuous adjustable (to distinguish the value of 0.01A) Constant current output accuracy: + 0.01A (MA constant current precision: + 1mA) The current stability of the Load stability Ripple noise current 4, current and voltage display accuracy Voltage display accuracy: + 0.1V (constant current state) Current display accuracy: + 0.01A (constant pressure) Ma current display accuracy: + 1mA (constant pressure) 5, storage capacity Storage and call ten current,

Description:   1. The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0V to 5V pulse. (or 0V to 3.3V pulse if you solder SJ2 closed on the EasyDriver) 2. EasyDriver requires a 7V to 30V supply to power the motor and can power any voltage of stepper motor. 3. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4, 6, or 8 wire stepper motors. 4. It provides much more flexibility and control over your stepper motor, when compared to older versions. The microstep select (MS1 and MS2) pins of the A3967 are broken out allowing adjustments to the microstepping resolution. The sleep and enable pins are also broken out for further control.cjmcu made.   Features:   1. MS1 and MS2 pins broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth) 2. Compatible with 4, 6, and 8 wire stepper motors of any voltage 3. Adjustable current control from 150mA / phase to 750mA / phase 4. Power supply range from 7V to 30V. The higher the voltage, the higher the torque at high speeds 5. Distribution pin, not welded, this module is open source   Note:   Do not connect or disconnect a motor while the driver is energized.This will cause permanent damage to the A3967 IC. Chip data: https://www.alldatasheetcn.com/datasheet-pdf/pdf/83571/ALLEGRO/A3967.html   Package included:   3 X A3967 easy driver stepper motor driver board

TRANSIENT VOLTAGE SUPPRESSOR; AXIAL LEADED; UNI-DIRECTIONAL; 1500W; STANDOFF=25.6V; BREAKDOWN=30V; CLAMP=41.4V

HEXFET POWER MOSFET; WITH LOGIC LEVEL GATE DRIVE VDS=30V; ID=116A; RDS=0E007; IP=400A

SURFACE MOUNT N CHANNEL FIELD EFFECT TRANSISTOR; DUAL; 30V; 8A; SOIC8 PACKAGE

SCHOTTKY BARRIER (DOUBLE) DIODE Vr=30V If=200mA VF=0.80V; TOP MARK: L44; WV4

SURFACE MOUNT N CHANNEL FET; 30V; 30A; ZENER PROTECTED GATE VDS=25V; ID=35A; RDS=0E014; IP=145; PT=39W

TRANSIENT VOLTAGE SUPPRESSOR; AXIAL LEADED; BI-DIRECTIONAL; 1500W; STANDOFF=25.6V; BREAKDOWN=30V; CLAMP=41.5V

10pcs DC 7V To 30V 150mA To 750mA A3967 Easy Driver Stepper Motor Driver Board For Arduino

BC308B transistors PNP high-gain 30V 100mA TO-92 Packet of 10 @ R3.00 per packet Many other types of transistors, capacitors, rectifiers, etc. listed. SAVE ON SHIPPING BY ORDERING A SELECTION OF COMPONENTS: SEE MY OTHER ADS Suggestions on customised listings of a variety of components welcome.     

Description DUAL MOSFET, P-CHANNEL & N-CHANNEL, SND, SO-8, 30V 3.5A More Products View More Products

Buy Electronic Load 9.99A 60W 30V Multi-functional Constant Current Discharge Power for R688.09

Buy 10pcs Blue 0.56 Inch Mini Digital Voltmeter DC 4.5V To 30V Digital Voltmeter Voltage Panel Meter For for R445.00

Buy Best Low, Low Price!! Transistor 2SA928A PNP 30V 2A TO-92L 10-pack for R7.00

Buy Best Low, Low Price!! Transistor BC308B High-Gain PNP 30V 100mA 10-pack for R5.50

Buy Original ZHIYU 60W / 110W 9.99A 30V Constant Current Electronic Load Aging Battery Capacity Tester for R421.97

Buy 5pcs 3V/5V/12V to 19V/24V/30V/36V DC Adjustable Boost Module LM2587 Power Suppl for R461.77

Buy 50Pcs TO-92 30V 0.6A 2N2222A Triode Transistor NPN 2N2222 Switch Transistors... for R189.00

Buy WANPTEK 30V Programmable Adjustable DC Regulated Power Supply 600-1200W PWM High Power... (TYPE: A) for R3,860.07

Buy 5pcs Green 0.56 Inch Mini Digital Voltmeter DC 4.5V To 30V Digital Voltmeter Voltage Panel Meter For for R297.00

Buy 3pcs Red 0.56 Inch Mini Digital Voltmeter DC 4.5V To 30V Digital Voltmeter Voltage Panel Meter For 6 for R223.71

Buy ESP8266 10A 220V Network Relay WIFI Module Input DC 7V~30V for R309.00

Buy 10pcs Green 0.56 Inch Mini Digital Voltmeter DC 4.5V To 30V Digital Voltmeter Voltage Panel Meter Fo for R402.85

Buy 10pcs DC 7V To 30V 150mA To 750mA A3967 Easy Driver Stepper Motor Driver Board for R377.73

Buy SCHOTTKY ARRAY DIODE SMD SOT23 30V 0.2A 3K/R BAT54S;215 *DBK* for R0.78

Buy 3pcs Blue 0.56 Inch Mini Digital Voltmeter DC 4.5V To 30V Digital Voltmeter Voltage Panel Meter For for R263.00