2wd smart robot

Buy 2WD Smart Robot Chassis Car Kit with Speed Encoder Support Wireless Control for R405.00

Buy 2WD Smart Robot Chassis Car Kit with Speed Encoder Support Wireless Control for R352.15

Specification: Platform height: 80mm Platform weight: 506g Platform length: 170mm Platform width: 170mm Wheel diameter: 65mm Wheel width: 26mm Distance from the ground to the ground: 20mm Drive motor gearbox speed ratio: 1: 120 Drive motor no-load speed: 120rpm Torque (3V): 4500mg * cm Torque (6V): 6700mg * cm Package Included: 1 x Smart Robot Car Kit

Smart Robot Car Chassis Kit Wireless Control For Arduino Carton Packaging Feature: Smart car chassis tracing car Robot car chassis with code disk Ideal for DIY Mechanical structure is simple, it is easy to install This car is the tachometer encoder With a 4 AA battery box (batteries not included) Can be used for distance measurement, velocity Can use with other devices to realize function of tracing, obstacle avoidance, distance testing, speed testing, wireless remote control Size: 20 x 14cm (L x W) Wheel size: 6.5 x 2.7cm (Dia. x H) Note: Motor power supply is 3V ~ 6V. All the parameter above is tested without load. The car Chassis is transparent, you need to tear out protective paper. This version is the same with SKU115409, but this version has better packaging. It may be individually packaged with foam box or carton box. Package included: 1 x Car chassis 2 x Gear motor 2 x Car tire 2 x Speed encoder 2 x Fastener 1 x Universal wheel 1 x Screwdriver 1 x Battery box(batteries not included) All necessary screw and nut

Buy 2WD Balance Car Chassis Smart Robot Car Kit Silver Panel/65mm Wheel/37-520 Moto for R1,045.61

Buy 2WD Avoidance Tracking Smart Robot Chassis Car Kit With Speed Encoder Ultrasonic For UNO R3 for R683.00

Buy 2WD Balance Car Chassis Smart Robot Car Kit Silver Panel/65mm Wheel/37-520 Moto for R1,212.80

Specifications: 1. Color: Blue/Silver 2. Weight: about 160g 3. Diameter: 130mm 4. Wide: 60MM 5. Suitable: Lengthen the Coupling, Motor bore (inner diameter): 4/5/6mm 6. For: Smart robot car 7. Tire skin Material: Rubber Note: *It does not include the coupling. *You can measure the motor shaft diameter, according to the motor shaft diameter to choose the diameter of the coupling separately. Package Included: 1 x Blue/Silver Rubber Wheel

Buy Smart Robot Part Plastic Track + Driving Wheel + Bearing Wheel Accessory Set Fo for R511.30

Buy Smart Robot Part Plastic Track + Driving Wheel + Bearing Wheel Accessory Set For DIY Kit for R350.00

1Set 2WD Mini Round Double-Deck Smart Robot Car Chassis DIY Kit For Arduino

Buy 5Pcs 2WD Ultrasonic Smart Robot Car Chassis Tracking Car DIY Kit For - Free Shipping for R3,890.00

Buy 3Pcs/Pack 2WD Ultrasonic Smart Robot Car Chassis Tracking Car DIY Kit For for R2,454.12

Buy 3Pcs/Pack 2WD Ultrasonic Smart Robot Car Chassis Tracking Car DIY Kit For for R1,580.00

Specifications: 1.Photoresistor (LDR) based line following 2.Individual wheel control 3.Chipset: LM393 4.Material: Electrical components 5.Color: See picture 6.Board Size:10.4*7.2cm The assembly steps: Step 1: Welding circuit - Electric welding part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance is important to use the multi meter to confirm resistance is correct Step 2: Mechanical assembly - The red line is connected to the 3V positive power supply, the yellow line grounding, the excess wire can be used for the motor wire. Step 3: The installation of a photoelectric circuit - Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test. Step 4: Vehicle debugging - The right direction is along the universal wheel direction if you press and hold the left photoresistor - The wheels on the right side of the car should be rotated. Press and hold the right photoresistor - The wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring on the back side. Note: The battery is not included. Package Included: 1 x Base board 1 x 35mm Wheels 1 x Rubber Wheel bands 1 x AA Battery holder 1 x Screw set 1 x LM393 Chipset 1 x 8pin DIP Socket 10 x Resistor 2 x Gearded DC Motors 2 x Electrolytic capacitor 2 x Light dependant resistors 2 x Transitors 2 x White LED 2 x Red LED 1 x Power switch 4 x 70mm Leads