24v 1000w holes

1000W Set Consists off the following: 2 x Deltec 102A/H Deep Cycle Lead Acid Battery 1000W 24V Pure Sine Wave Inverter with build in battery charger 2 x 100W Solar Panel 20A Solar Charge Controller with LCD Display a 4 x 1m Solar Aluminium Strut 8 x Araymond Powersnap 10m Red 6mm PV Cable 10m Black 6mm PV Cable 1 x Double Battery Box with castor wheels Set to be used for tv, hi-fi, decoder, cellphone charging and 6 led lights for approx 4 – 5 hours.

Note: You must need to pay attention to safety, will produce high pressure / high temperature when using this product. Feature: Suitable heating brass: 24V / 48V (package does not includes) Suitable heating brass: 30 x 30mm (this size can melted about 50g copper) Default input voltage: DC 12V ~ 40V Cooling fan rated voltage: DC 24V Maximum input current: 20A, short working time 25A, long working time ≤15A PCB board size: 181.10 * 88.46 * 1.60mm Input voltage Maximum power Current DC 48V ~ 55V 1000W ≥30A DC 36V 720W ≥30A DC 24V 480W ≥20A DC 12V 240W ≥15A Note: Must ensure that the operating voltage is 11V above, note: this is the working voltage, that is the input voltage of connected to the heating coil or an heated object, not the no-load voltage. Whenever possible, as far as possible use protection power supply. It does not recommend to use adjustable power supply, if you must need to use the adjustable power supply, voltage and current must reach scope of the note! Recommended input voltage range is DC 24V ~ 36V, need to melt steel recommended input voltage is DC 48V ~ 55V. To melt the metal, you must need to use a graphite crucible. This board can melt iron, copper, aluminum: Can melt copper is about 100g, need to split adds, can melt about 50g once, until melted and then added again. Must confirm that the wiring is correct, correct the negative power input not reversed, it must be connected to the load (ie, the heating coil) before power on! Be sure to connect the load before power on, it can not load! Do not use batteries, battery-powered! When using the induction heating, you must need to use copper pipes as coil and water-cooled! Cooling fan must be turned on! The maximum output of the pillars can be installed max. 10mm diameter copper pipe, copper pipe diameter ≤4mm can be soldered to the copper brass clip and then fixed pillars, diameter ≤2mm can be connected to the output terminals. Do not touch any place after power on! Package includes: 1 x 1000W ZVS High Frequency Induction Heating Machine

If you need power supply, please buy it separately: Product ID: 1196806 Note: You must need to pay attention to safety, will produce high pressure / high temperature when using this product. Feature: Suitable heating brass: 24V / 48V (package does not includes) Suitable heating brass: 30 x 30mm (this size can melted about 50g copper)Default input voltage: DC 12V ~ 40VCooling fan rated voltage: DC 24VMaximum input current: 20A, short working time 25A, long working time ≤15APCB board size: 181.10 * 88.46 * 1.60mm Input voltage Maximum power Current DC 48V ~ 55V 1000W ≥30A DC 36V 720W ≥30A DC 24V 480W ≥20A DC 12V 240W ≥15A Note: Must ensure that the operating voltage is 11V above, note: this is the working voltage, that is the input voltage of connected to the heating coil or an heated object, not the no-load voltage. Whenever possible, as far as possible use protection power supply.It does not recommend to use adjustable power supply, if you must need to use the adjustable power supply, voltage and current must reach scope of the note!Recommended input voltage range is DC 24V ~ 36V, need to melt steel recommended input voltage is DC 48V ~ 55V.To melt the metal, you must need to use a graphite crucible.This board can melt iron, copper, aluminum:Can melt copper is about 100g, need to split adds, can melt about 50g once, until melted and then added again.Must confirm that the wiring is correct, correct the negative power input not reversed, it must be connected to the load (ie, the heating coil) before power on! Be sure to connect the load before power on, it can not load!Do not use batteries, battery-powered!When using the induction heating, you must need to use copper pipes as coil and water-cooled! Cooling fan must be turned on!The maximum output of the pillars can be installed max. 10mm diameter copper pipe, copper pipe diameter ≤4mm can be soldered to the copper brass clip and then fixed pillars, diameter ≤2mm can be connected to the output terminals.Do not touch any place after power on! Package includes: 1 x 1000W ZVS High Frequency Induction Heating Machine

Buy 1000W (1,2Kva) 24v MICROCARE Pure Sine Wave Bi-Directional Inverter & charger (UPS) Li-Ion comp. for R10,075.00

Buy 1000W Peak 12V/24V DC to 110V/220V AC Solar Power Inverter LED Modified Sine Wa for R1,078.38

Description: 24V 5A 120W AC/DC Power Supply Adapter for 2.1 & 2.5mm LED Strip Security Camera etc. Features: 1. Provide consistent power and reliable performance. 2. Replacement 24V 5A Power Supply AC Adapter For many devices with 5.5mm x 2.5mm/2.1mm plug tip(such as LCD/ LED/ TV Sound Box/ LED Strip/ Security CCTV Camera DVR ect.) 3. Has ventilation holes in front and back, make sure it will work efficiently and not be over-heat. Specifications: 1. Output Voltage & Amps: 24V 5A (120W) 2. Input: AC 100-240V / 50-60Hz (Worldwide Use) 3. Connector: 5.5mm x 2.5mm (Compatible for Both 2.5mm&2.1mm Connector) 4. Dimension: 150*65*38(mm) Package includes: 1 x 120W AC/DC Power Adapter Details pictures:

Package Included: 1 x Power Inverter 1 x Battery Clip Cable 1 x Charger Specification: Output Voltage: AC 230V Input Voltage: DC 24V Material: Aluminum Alloy Output Frequency: 50HZ Output Waveform: Modified Sine Wave RMS Power: 1000W No-load Current: Conversion Efficiency: 80% Low Battery Alarm: 10.4 - 11V Low Battery Shutdown Point: 9.0 - 10.5V High Battery Shutdown Point: 14.5 - 15.5V Dimension: Approx. 20.5x11.2x5.5cm/ 8.07x4.41x2.17" Battery Clip Cable Length: Approx. 60cm/ 23.62" Car Charger Length: Approx. 55cm/ 21.65" Feature: Invert DC 24V to household AC 230V, power a wide variety of household AC products. Have a fully functional protective circuit: short circuit, overrating, overload overtemperature, inverse protection. The output port is a universal socket, compatible with most plugs. Independent power switch, directly control the inverter work, independent USB interface, convenient mobile device charging. Intelligent cooling fan, can greatly improve the service life of the inverter. Suitable for family, industry, travel and other activities. More details:

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: Maximum load: AC 250V/10A, DC 30V/10A. The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA. Working voltage: 24V. Every channel of the module can be set high or low level trigger by jumper. Fault tolerant design, even if the control line is disconnect, the relay will not act. Power indicator (green), 1 relay status indicator (red). The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient. Module size: 50mm x 25mm x 18.5mm (length x width x height). There are 4 fixed bolt holes, holes 3.1mm, spacing 67mm x 44.5mm. Module interface: 1, DC+: Connect the power positive pole. 2, DC-: Connect the power negative pole. 3, IN1: Can be controlled by high or low level. Relay output: there is a 3 wire interface, all interfaces can be directly connected to lead to facilitate user use. 1, NO1: Relay normal open, the relay suspends before pulling in, and then short-connect with the COM. 2, COM1: Relay common interface 3, NC1: Relay normal close, short connected with COM before pulling in and suspended after pulling in. High and low level trigger option: 1. The 3-pin is the high level trigger selection. 2. When COM is short connected with LOW, the corresponding relay is LOW level trigger, while when COM is short connected with high end is high level trigger. Package Included: 1 x 1 Channel 5V Relay Module BESTEP 1 Channel 24V Relay Module High And Low Level Trigger For Arduino BESTEP 1 Channel 24V Relay Module High And Low Level Trigger For Arduino BESTEP 1 Channel 24V Relay Module High And Low Level Trigger For Arduino

Description: Maximum load: AC 250V/10A, DC 30V/10A. The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA. Working voltage is 24V. Each channel of the module can be set up by high jumper or low level trigger. Fault tolerant design, even if the control line is broken, the relay will not act. Power indicator (green), 8 relay status indicator (red). The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient. Module size: 142mm x 50mm x 18.5mm (length x width x height). There are 4 fixed bolt holes, holes 3.1mm, spacing 67mm x 44.5mm. Module interface: 1. DC+: Connect the power positive pole 2. DC-: Connect the power negative pole. 3. IN1-IN8: According to the setting of each way, the corresponding relay-operating can be controlled by high or low level. Relay output: there is a 24 wire interface, all interfaces can be directly connected to lead to facilitate user use. 1. NO1--NO8: Relay normal open, the relay suspends before pulling in, and then short-connect with the COM. 2. COM1--COM8: Relay common interface 3. NC1--NC8: Relay normal close, short connected with COM before pulling inand suspended after pulling in. High and low level trigger option: 1. S1-S8 is the high level trigger selection of relay 1 Channel - 8 Channel. 2. When COM is short connected with LOW, the corresponding relay is LOW level trigger, while when COM is short connected with high end is high level trigger. Package Included: 1 x 8 Channel 24V Relay Module

It is fullcolor led strobe, You can choose different colors to blink according to different scene requirements,you can choose red, or blue,or green,or white(when RGB threecolors mix),If you use a snowflake machine, when it snows, the blue light flashes white snow, which is wonderful. It use led lamp, each is 1w, total 1000pcs lamp, The brightness is equal to the old strobe which use glass tube,and it's not going to get hot,so the led lamp wont bad, You don't need to stop in 5 minutes, you can continue to flash for 24 hours,it has Long-Life 100000 hours,You don't need to replace the glass tube like before It had perfect program, similar martin strobe,can Blackout,Flash rate, slow to fast,Continuous Blindereffect,it with Dmx512,you can control it by dmx console, if you're not familiar with the console, you can use it without console, use music controlled,Automatic,Master/Slave It come with Bow hanging,There are five holes on the hanging,You can easily hang it, there has knob at both ends, if you place it on the ground,You can adjust the knob to hold it in any Angle It has a perfect body,use Explosion-proof toughened glass,even broken, It doesn't hurt people Rated Voltage:AC 90-240V Rated Frequency:50-60Hz Rated Power:1000W 6500-7500K Diodes Quantity:1000PCS*1W 5054 High Brightness RGB 3IN1 LEDS Channel: 8Channels Size:54x32x21cm N.W.: 7.5kg G.W.: 8.5kg Control Signal:Standard DMX-512 Signal Function Mode:DMX-512 controlled,music controlled,Automatic,Master/Slave Working Environment:Indoor use Package included: 1x Led Strobe Light 1x US Type Plug 1x 3m DMX Signal Cable 1x English User Manual

Buy Bakeey 500-800W 12V 24V Car Glass Defroster Window Heater 4 Holes Air Outlet Wa for R1,549.36

1000 WATT TRUE SINE WAVE DC-AC POWER INVERTER INPUT: 21-30VDC OUTPUT: 220 VAC - 1000 WATT / 4.5 AMP

Specification Nominal Basket Diameter 18″, 457.2mm Nominal Impedance* 8 ohms Power Rating** Watts 500W Music Program 1000W Resonance 28Hz Usable Frequency Range 35Hz – 2kHz Sensitivity*** 97dB Magnet Weight 125 oz. Gap Height 0.37″, 9.53mm Voice Coil Diameter 4″, 100mm Thiele & Small Parameters Resonant Frequency (fs) 28Hz DC Resistance (Re) 6.29 Coil Inductance (Le) 1.9mH Mechanical Q (Qms) 8.28 Electromagnetic Q (Qes) 0.3 Total Q (Qts) 0.29 Compliance Equivalent Volume (Vas) 441.2 liters / 15.6 cu.ft. Peak Diaphragm Displacement Volume (Vd) 695cc Mechanical Compliance of Suspension (Cms) 0.24mm/N BL Product (BL) 22.1 T-M Diaphragm Mass Inc. Airload (MMs) 130 grams Efficiency Bandwidth Product (EBP) 93 Maximum Linear Excursion (Xmax) 6.1mm Surface Area of Cone (Sd) 1140 cm2 Maximum Mechanical Limit (Xlim) 18mm Mounting Information Recommended Enclosure Volume Sealed N/a Vented 93-212 liters / 3.3-7.5 cu.ft. Driver Volume Displaced 403.9 cu.in. / 6.62 liters Overall Diameter 18″, 457.2mm Baffle Hole Diameter 16.56″, 420.5mm Front Sealing Gasket Fitted as standard Rear Sealing Gasket Fitted as standard Mounting Holes Diameter 0.28″, 7.1mm Mounting Holes B.C.D. 17.25″, 438.2mm Depth 8.15″, 207mm Net Weight 24.5 lbs, 11.1 kg Shipping Weight 28.1 lbs, 12.8 kgs Materials of Construction Coil Construction Copper voice coil Coil Former Polyimide former Magnet Composition Ferrite magnet Core Details Vented and extended core Basket Materials Die-cast aluminum basket Cone Composition Paper cone Cone Edge Composition Cloth cone edge Dust Cap Composition Solid composition paper dust cap

10W Watt 12V PolyCrystalline Poly Solar Panel Module Battery ChargerDescription: Maximum output power: 10 Watts Operating voltage: 17 V Current: 0.59 A Short circuit current: 0.65 A Open circuit voltage: 21.5 V Size: 346mm * 230 * 17mm Crystal silicon type: polycrystalline silicon Solar cells Number: 36 pcs Front cover glass: Tempered glass Border: stainless steel aluminum   Test conditions (AM1.5,1000W / m2,25 ¿¿¿): a. single block solar panels was for 12v battery charging. b. 24v battery charging, two solar panels can be connected in series. c. charging the phone, in the middle need to add step-down module.   Junction Box: Electric panel produce current was direct current, the back of electric panel have a black junction boxes, "positive and negative" pole binding posts. Binding posts with fastening screw for securing the output wires.   Application:   1) solar garden lighting 2) Small home lighting system 3) solar street lighting 4) Solar Outdoor Advertising 5) for a variety of low-power appliances, emergency lights, advertising lights, traffic lights, household lights, fans, such as solar water pumps, solar lights, small solar systems Package included: 1 x PolyCrystalline Cells Solar Panel

Description: 2 pcs ATTEN 4-Core 50W Soldering Irons Heating Element Ceramic Heater for AT936b at8586 ATTEN 4-Core 50W ceramics heat elements is using imported temperature-resistant materials, four lines heating for longtime use, low cost but high quality, low power supply to ensure antistatic electricity, no power losing,no interference and quick reaching required temperature. Special for constant temperature soldering station: AT936b AT8586 (Will Not Suit for HAKKO), also for combo rework soldering stations    For 7 holes handle replacement. White wire for 24V DC Red and Yellow for temperature control (↓We also take 2 pictures to show the connect, please see our details pictures.) Package includes: 2 x Ceramics Heating Element Details pictures: