20pcs 5v

Buy 20Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module for R670.00

Buy 20pcs 5V LED Traffic Light Display Module Electronic Building Blocks Board Geekcreit for Arduino - p for R289.00

Feature: Operating voltage: 5V On-board MAX485 chip A low power consumption for the RS-485 communication Slew-rate limited transceiver 5.08mm pitch 2P terminal Convenient RS-485 communication wiring All pins of chip have been lead to can be controlled through the microcontroller Board size: 44 x 14mm Package included: 20 x MAX485 TTL to RS485 module

Feature: Quantity: 1pc Size: 3.5 x 1cm Power supply: 5V DC Detector distance: 10mm Build-in Tcrt5000 Sensor NSOR Applicable to a variety of platforms including Arduino / AVR / ARM /PIC Package included: 20 x Infrared line track follower sensor module

Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load: AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 20 x 1 Channel H/L level trigger optocoupler relay module

20Pcs 8-Channel Logic Level Translator Converter Bi-Directional Module Introduction: If you've ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. This level converter also works with 2.8V and 1.8V devices. What really separates this Logic level converter from our previous versions is that you can successfully set your high and low voltages and step up and down between them safely on the same channel. Each level converter has the capability of converting 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side. The level converter is very easy to use. The board needs to be powered from the two voltages sources (high voltage and low voltage) that your system is using. High voltage (5V for example) to the 'HV' pin, low voltage (3.3V for example) to 'LV', and ground from the system to the 'GND' pin. Feature: 8-channel high-voltage and low-voltage logic bidirectional translation Mini size, 4.1cm x 1.8cm Comes with 2 rows of 6pin, unsoldered Compatible breadboard, can be directly inserted in the breadboard Note: (For example: High voltage: 5V, low voltage: 3.3V) HV connect 5V power supply LV connect 3.3V power supply GND connect negative, two power supply commons LVx input and output is 3.3V TTL, HVx input and output is 5V TTL, LVx and TVx bidirectional transfers Package includes: 20 x Eight Channel Logic Level Translator Converter

20Pcs Two Channel IIC I2C Logic Level Converter Bi-Directional Module 20Pcs Two Channel IIC I2C Logic Level Converter Bi-Directional ModuleFeature:Power supply:5V-3VAVCC connect to 5V system powerASCL connect to 5V system SCLASDA connect to 5V system SDAAGND connect to 5V system GNDBVCC connect to 3V system powerBSCL connect to 3V system SCLBSDA connect to 3V systems SDABGND connect to 3V system GNDPackage included:20 x Two Channel IIC I2C Logic Level Converter Bi-Directional Module

20Pcs MB102 Breadboard Module Adapter Shield 3.3V/5V For Arduino Board Description: Breadboard power supply module, compatible with 5 V, 3.3 V Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: Fluctuation two road independent control, can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient external lead use. Size: 5.3*3.2*2.5cm Weight: 12g Please notice: this item only a Power Supply Module, Breadboard is not included. Package included: 20 x Power supply module Breadboard power supply module, compatible with 5 V, 3.3 V.      

20Pcs DC-DC 12V to 3.3V/5V/12V Voltage Converter Power Supply Module Board Feature:One channel input: DC 6V - 12V (the input voltage must be higher than the output voltage to 1V or more.)Triple output: 3.3V (ﾱ 0.05v error), 5V (ﾱ 0.05v error), 800mA (load current can not exceed 800ma), 12V (12V input directly to the output)Specially designed two rows of needle fixing hole, can be directly fixing on the plate to extend the experiment;Using multiple input and output pin, easy to use and connect;PCB board size: 4.5 x 4.5cmWith power indicator (red)Package includes:20 x Multi-output Power Supply Module

20Pcs Two Channel IIC I2C Logic Level Converter Bi-Directional Module Feature: Power supply:5V-3V AVCC connect to 5V system power ASCL connect to 5V system SCL ASDA connect to 5V system SDA AGND connect to 5V system GND BVCC connect to 3V system power BSCL connect to 3V system SCL BSDA connect to 3V systems SDA BGND connect to 3V system GND Package included: 20 x Two Channel IIC I2C Logic Level Converter Bi-Directional Module

20Pcs AMS1117 5V Power Supply Module With DC Socket And Switch Package contains 1 X item of the smallest listed variant.

20Pcs NE555 Pulse Frequency Duty Cycle Adjustable Module Square Wave Signal Generator Features: 1. As a square wave signal generator,generates a square wave signal used for experimental development. 2. Used to drive a stepper motor for generating a square wave drive signal. 3. Generate adjustable pulse for MCU. 4. Generate adjustable pulse,to control circuitry associated. 5. Size: 31mm x 22mm 6. Main chip: NE555 7. Input Voltage: 5V-15V DC. When power supply is 5 V, the output current can be 15 MA around; when 12V power supply, the output current can 35 MA around 8. Input current: >=100 MA 9. Output amplitude: 4.2V V-PP to 11.4V V-PP. (Different input voltage, the output amplitude will be different) 10. Maximum output current: >=15MA (5V power supply, V-PP greater than 50%), >=35MA (12V power supply, V-PP greater than 50%) 11. Output with LED indication(low level,LED will on; high level,LED will off;low frequency, the LED flashes) 12. The output frequency range is selectable: LF file: 1Hz ~ 50Hz                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                        &nbs

20pcs 5MM LED Flashlight Convenient Light Kit Simple LED Boost Drive DIY Electronic Kit Feature:ￂ Shell size: 55 x 35 x 15mmPCB board size: 5 x 2 x 1mmOperating voltage: 1.5V (AAA battery)Kit weight: 17 gramsNote: This is a DIY kit, you need to assemble it.ￂ ￂ Package includes:ￂ 20 x Plastic housing20 x PCB board20 x 8*8 self-locking switch20 x 7mm self-locking switch cap20 x Single wire 5CM20 x 8550 transistor20 x 8050 triode20 x 5MM Straw Hat LED20 x 330UH inductor20 x 102 ceramic capacitor20 x 510 ohm resistor20 x 20K resistance20 x Battery positive piece20 x Battery negative piece

20Pcs Soil Hygrometer Humidity Detection Moisture Sensor For Arduino Description: This is a summary of the soil moisture sensor can be used to detect moisture, when the soil is dry, the module outputs a high level, whereas output low. Using this sensor make an automatic watering system, so that your garden plants without people to manage. Operating voltage: 3.3V~5V. Adjustable sensitivity (shown in blue digital potentiometer adjustment) Dual output mode,analog output more accurate. A fixed bolt hole for easy installation. With power indicator (red) and digital switching output indicator (green). Having LM393 comparator chip, stable. Panel PCB Dimension: 3cm x 1.5cm. Soil Probe Dimension: 6cm x 2cm. Cable Length: 21cm. VCC: 3.3V-5V. GND: GND. DO: digital output interface(0 and 1). AO: analog output interface. Instructions for Use: 1. Soil moisture module is most sensitive to the ambient humidity is generally used to detect the moisture content of the soil. 2. Module to reach the threshold value is set in the soil moisture, DO port output high, when the the soil humidity exceeds a set threshold value, the module D0 output low. 3. The digital output D0 can be connected directly with the microcontroller to detect high and low by the microcontroller to detect soil moisture. 4. The digital outputs DO shop relay module can directly drive the buzzer module, which can form a soil moisture alarm equipment. 5. Analog output AO and AD module connected through the AD converter, you can get more precise values of soil moisture. Package Included: 20 x Soil moisture detector module 20 x Probe 20 x 2P Jumper Cable

20Pcs Laser Receiver Non-modulator Tube Sensor Module For Arduino Features: PCB size: 1.5 x 1.9cm Working voltage: 5V Output high level when receive laser signal Output low level when not receive laser signal Note: The sensor uses a non-modulated laser receiver, please use indoors where no light, sunlight or other fixtures may interfere, recommended for use in dark environments. Package included: 20 x Laser sensor module

Buy 20pcs 7W Mini DC DC Boost Step Up Converter 2.6-5.5V to 5V Voltage Regulator Module for R784.35

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: 1. Ultramicro volume: 23*24MM 2. Excellent noise suppression. If you don't receive input audio, you can't hear any noise on your ears. 3. Double channel stereo, 5V power supply can output 5W+5W power, can directly drive the 4 Omega, 8 Omega small sound box, the output power is big, the energy is full, the sound quality is good, with the volume adjustment of the right and left channel. 4. The unique D type digital power plate without LC filter can be directly powered by the USB of the computer. 5. Double panel wiring, properly solve the ground potential balance caused by wiring and inter channel crosstalk. 6. The ultra micro design can be easily placed in the small space of various digital products, and the amplification efficiency is super high. 7. The whole board is welded by machine. The welding quality is comparable to that of the manual soldering iron. 8. Rated working voltage is 2.5-5V, the limit working voltage is 5.5V. Package included: 20 x PAM8406 Digital Amplifier Board 20pcs 5Wx2 PAM8406 Digital Amplifier Board Volume Potentiometer Stereo Noiseless Power Amplifier 20pcs 5Wx2 PAM8406 Digital Amplifier Board Volume Potentiometer Stereo Noiseless Power Amplifier 20pcs 5Wx2 PAM8406 Digital Amplifier Board Volume Potentiometer Stereo Noiseless Power Amplifier

Buy 20pcs 0.7-5V to 5V DC DC Boost Power Supply Step Up Module Converter Voltage Regulator for R720.00

Buy 20pcs DC/DC 5V AMS1117-5V 800mA Power Supply Module Voltage Regulator for R219.08

Buy 20Pcs DC-DC 12V to 3.3V/5V/12V Voltage Converter Power Supply Module Board for R577.67

Buy 20pcs MP1584 5V Buck Converter 7-30V Adjustable Step Down Regulator Module with Switch OPEN-SMART fo for R1,130.00

Buy 20Pcs MB102 Breadboard Module Adapter Shield 3.3V/5V for R500.05

Buy 20pcs Vehicle Charger Motherboard Module 5V 2.4A Car Charging Board for R748.55

Buy 20pcs 3.3V 5V 8 Bit Blue Common Cathode LED Indicator Display Module DIY Kit for R527.07

Buy 20Pcs MB102 Breadboard Module Adapter Shield 3.3V/5V Geekcreit for Arduino - products that work with for R510.88

Buy 20pcs USB Power Boost Line DC 5V to DC 12V Step UP Module USB Converter for R825.15

Buy 20pcs CJMCU-2662 LM2662 1.5-5.5V 400mA Negative Polarity Inversion Capacitor Switch Board for R831.60

Buy 20pcs 2.5-5.5V TTP223 Capacitive Touch Switch Button Self Lock Module for R148.77

Buy 20pcs TB293 7W USB DC to DC 5V to 6V 9V 12V 15V Adjustable Output Converter for R1,227.31

Buy 20pcs 3.3V 5V 8 Bit Blue Common Cathode LED Indicator Display Module DIY Kit for R458.00