12v acid lead batteries

12V 6-63V LCD Acid Lead Lithium Battery Capacity Indicator Digital Voltmeter Package weight: 0.02 kg Specification: Display: Power, Voltage, Close, the key for cycle. Voltage Range: 6-63V, products will display based on the voltage value, voltage fluctuations, power meter will be follow as the voltage fluctuation! (Comes with reverse polarity protection, can be guarantee use effectively) The product is suitable for lead-acid 12V, 24V, 36V, 48V (can be changes via key, specific please see setup instructions as below) The product is suitable for 3.7V lithium series multi-platform, 3 string, 4 string, 5 string, 6 string, 7 string and 8 string 9 string 10 string 11 string 12 string 13 string 14 string 15 string (can be changes via key, detail information please see as below) Cable Length: 30cm Instructions: 1. Press and hold switch on the product, power on, automatically select the interface (please follow as the code corresponds blow) 2. Select your battery type after corresponding, for example 3 series lithium battery, you need to enter the selection screen, press the key point to for L3 interface, then off, re-energized, choose success, such as the need to set 12V lead-acid batteries, the key point press to P12V interface, power, re-energized, both choose success 3. instruments can be used if you Select successful. Meter shows the power interface, tap switch, switch to voltage interface, click the switch, turn off the meter. cycle shown as the code corresponds Fitment: Code: Suitable for For L3: 3 string lithium L4: 4 string lithium L5: 5 string lithium L6: 6 string lithium L7: 7 string lithium L8: 8 string lithium L9: 9 string lithium L10: 10 string lithium L11: 11 string lithium L12: 12 string lithium L13: 13 string lithium L14: 14 string lithium P12V: 12V lead-acid P24V: 24V lead-acid P36V: 36V lead-acid P48V: 48V lead-acid Note: Special Function Setting (requires electric iron, you must power off setting, electric iron must be grounded) A point connection, the backlight will be automatically shut down if delay10 seconds, the voltage fluctuation will automatic wake-up exceeds 0.3V / 0.5 seconds. B point connection, lithium choose 3-4.1V curve (lithium professionals) Package Included: 1 X Battery Capacity&Volt Tester 1 X Cable Click here for more deals 12V 6-63V LCD Acid Lead Lithium Battery Capacity Indicator Digital Voltmeter 12V 6-63V LCD Acid Lead Lithium Battery Capacity Indicator Digital Voltmeter

Specification: Display: Power, Voltage, Close, the key for cycle. Voltage Range: 6-63V, products will display based on the voltage value, voltage fluctuations, power meter will be follow as the voltage fluctuation! (Comes with reverse polarity protection, can be guarantee use effectively) The product is suitable for lead-acid 12V, 24V, 36V, 48V (can be changes via key, specific please see setup instructions as below) The product is suitable for 3.7V lithium series multi-platform, 3 string, 4 string, 5 string, 6 string, 7 string and 8 string 9 string 10 string 11 string 12 string 13 string 14 string 15 string (can be changes via key, detail information please see as below) Cable Length: 30cm Instructions: 1. Press and hold switch on the product, power on, automatically select the interface (please follow as the code corresponds blow) 2. Select your battery type after corresponding, for example 3 series lithium battery, you need to enter the selection screen, press the key point to for L3 interface, then off, re-energized, choose success, such as the need to set 12V lead-acid batteries, the key point press to P12V interface, power, re-energized, both choose success 3. instruments can be used if you Select successful. Meter shows the power interface, tap switch, switch to voltage interface, click the switch, turn off the meter. cycle shown as the code corresponds Fitment: Code: Suitable for For L3: 3 string lithium L4: 4 string lithium L5: 5 string lithium L6: 6 string lithium L7: 7 string lithium L8: 8 string lithium L9: 9 string lithium L10: 10 string lithium L11: 11 string lithium L12: 12 string lithium L13: 13 string lithium L14: 14 string lithium P12V: 12V lead-acid P24V: 24V lead-acid P36V: 36V lead-acid P48V: 48V lead-acid Note: Special Function Setting (requires electric iron, you must power off setting, electric iron must be grounded) A point connection, the backlight will be automatically shut down if delay10 seconds, the voltage fluctuation will automatic wake-up exceeds 0.3V / 0.5 seconds. B point connection, lithium choose 3-4.1V curve (lithium professionals) Package Included: 1 X 12V Battery Capacity&Volt Tester 1 X Cable

Specification: Display: Power, Voltage, Close, the key for cycle. Voltage Range: 6-63V, products will display based on the voltage value, voltage fluctuations, power meter will be follow as the voltage fluctuation! (Comes with reverse polarity protection, can be guarantee use effectively) The product is suitable for lead-acid 12V, 24V, 36V, 48V (can be changes via key, specific please see setup instructions as below) The product is suitable for 3.7V lithium series multi-platform, 3 string, 4 string, 5 string, 6 string, 7 string and 8 string 9 string 10 string 11 string 12 string 13 string 14 string 15 string (can be changes via key, detail information please see as below) Cable Length: 30cm   Instructions: 1. Press and hold switch on the product, power on, automatically select the interface (please follow as the code corresponds blow) 2. Select your battery type after corresponding, for example 3 series lithium battery, you need to enter the selection screen, press the key point to for L3 interface, then off, re-energized, choose success, such as the need to set 12V lead-acid batteries, the key point press to P12V interface, power, re-energized, both choose success 3. instruments can be used if you Select successful. Meter shows the power interface, tap switch, switch to voltage interface, click the switch, turn off the meter. cycle shown as the code corresponds   Fitment: Code: Suitable for For L3: 3 string lithium L4: 4 string lithium L5: 5 string lithium L6: 6 string lithium L7: 7 string lithium L8: 8 string lithium L9: 9 string lithium L10: 10 string lithium L11: 11 string lithium L12: 12 string lithium L13: 13 string lithium L14: 14 string lithium P12V: 12V lead-acid P24V: 24V lead-acid P36V: 36V lead-acid P48V: 48V lead-acid   Note: Special Function Setting (requires electric iron, you must power off setting, electric iron must be grounded) A point connection, the backlight will be automatically shut down if delay10 seconds, the voltage fluctuation will automatic wake-up exceeds 0.3V / 0.5 seconds. B point connection, lithium choose 3-4.1V curve (lithium professionals)   Package Included: 1 X Battery Capacity&Volt Tester 1 X Cable

Specification: Display: Power, Voltage, Close, the key for cycle. Voltage Range: 6-63V, products will display based on the voltage value, voltage fluctuations, power meter will be follow as the voltage fluctuation! (Comes with reverse polarity protection, can be guarantee use effectively) The product is suitable for lead-acid 12V, 24V, 36V, 48V (can be changes via key, specific please see setup instructions as below) The product is suitable for 3.7V lithium series multi-platform, 3 string, 4 string, 5 string, 6 string, 7 string and 8 string 9 string 10 string 11 string 12 string 13 string 14 string 15 string (can be changes via key, detail information please see as below) Cable Length: 30cm Instructions: 1. Press and hold switch on the product, power on, automatically select the interface (please follow as the code corresponds blow) 2. Select your battery type after corresponding, for example 3 series lithium battery, you need to enter the selection screen, press the key point to for L3 interface, then off, re-energized, choose success, such as the need to set 12V lead-acid batteries, the key point press to P12V interface, power, re-energized, both choose success 3. instruments can be used if you Select successful. Meter shows the power interface, tap switch, switch to voltage interface, click the switch, turn off the meter. cycle shown as the code corresponds Fitment: Code: Suitable for For L3: 3 string lithium L4: 4 string lithium L5: 5 string lithium L6: 6 string lithium L7: 7 string lithium L8: 8 string lithium L9: 9 string lithium L10: 10 string lithium L11: 11 string lithium L12: 12 string lithium L13: 13 string lithium L14: 14 string lithium P12V: 12V lead-acid P24V: 24V lead-acid P36V: 36V lead-acid P48V: 48V lead-acid Note: Special Function Setting (requires electric iron, you must power off setting, electric iron must be grounded) A point connection, the backlight will be automatically shut down if delay10 seconds, the voltage fluctuation will automatic wake-up exceeds 0.3V / 0.5 seconds. B point connection, lithium choose 3-4.1V curve (lithium professionals) Package Included: 1 X Battery Capacity&Volt Tester 1 X Cable

SELECTED OPTION: ADAPTOR: US CLICK HERE for more options in this item. Description: The difference between manual and automatic mode: Manual: It can be used for small capacity,Low temperature(under 0 ° C) and large Internal resistancethe battery,charging current is bigger than automatic so it take less time than automatic,but there must has human monitoring to avoid damage battery, when the battery shell has temperature must stop charging!using manual mode can't more than 1 hour! Automatic:pulg AC power first then connect battery with charger,it will recognize volgate automatic,telligent and convenient. Highly recommended:in the winter(under 0 ° C),use automatic mode to charge full first then use manual mode for 0.5-1 hours. LED screen: it shows both charging voltage and current, Identify 12V/24V intelligent,the charging light will bright when charging,when charging full the light will off -Red is anode,black is cathode   Specification: Input Voltage: 110-250V Output voltage: 12V/24V automatic Current: 10A peak for 12V /7A peak for 24V Suitable Capacity: 10-100AH Power: 180W Frequency: 50-60HZ Length of Output Wire: 50-60cm Length of Input Wire: 120cm Type: Charger Features: Automatic, LED light, plug in, portable, reverse polarity protection, safety switch, trickle   Charging Stage: Constant current: means the battery voltage is lower than the set voltage of charger, then the charger supply constant charging current to maintenance both battery and battery charger; Constant Voltage: advanced pulse width modulation (PWM) technology, control the charger's current and output voltage accurate,avoid overcharge; Trickle charge mode: when the battery voltage and current is approaching the set voltage and current, it will turn to trickle floating charge from automatic mode,it means charge full,also can be charged with floating mode.   Package Included: 1 X Charger 1 X User Manual

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA 12V/24V LED Display Motorcycle Car Battery Charger Automatic Intelligent Pulse Repair Description: 1.This product is applicable to the 12V/24V lead acid battery. 2.Advanced pulse width modulation (PWM) technology is used to automatically charge batteries through a 4-stage charging. 3.The battery life can be significantly improved by digital pulse repairing method for the power chips of microcomputers. 4.Constant voltage charging will be arranged to provide various protections and avoid over-voltage, over-current, over-beating and electrode-positive, etc. 5.When the red indicator light of charging stops flashing or is dark, and LCD screen display is at full nars condition, the charging mode will change to floating charging, means the battery charging being finished. 6.The 12V input when automatic charging mode, full electric voltage of 13.8V to 14.3V, about 17V input when manual charging mode, must be artificial monitoring in case of overcharge if manual mode charging, suggest stop charging when the battery beating. Specification: 1. Color: Orange 2. Power Cord Length: 130 cm 3. Clip Cord Length: 60 cm 4. Input Voltage: AC 150-250 V 5.Output Voltage: 12 V /24 V 6. Current: 10 A 7. Frequency: 50-60 HZ 8. Power Supply: US Plug 9. Five Charging Modes: Constant Current Mode/Constant Voltage Mode/Trickle Mode/Floating Mode/No Load Mode 10. Suitable for Battery from 6 AH to 200 AH Note: 1.Do not block cooling hole or use the charger with the cooling fan off. 2.This product is non-waterproof, please avoid the water. Package Included: 1 X Battery Charger 1 X User Manual 12V/24V LED Display Motorcycle Car Battery Charger Automatic Intelligent Pulse Repair 12V/24V LED Display Motorcycle Car Battery Charger Automatic Intelligent Pulse Repair

Description: 1.This product is applicable to the 12V/24V lead acid battery. 2.Advanced pulse width modulation (PWM) technology is used to automatically charge batteries through a 4-stage charging. 3.The battery life can be significantly improved by digital pulse repairing method for the power chips of microcomputers. 4.Constant voltage charging will be arranged to provide various protections and avoid over-voltage, over-current, over-beating and electrode-positive, etc. 5.When the red indicator light of charging stops flashing or is dark, and LCD screen display is at full nars condition, the charging mode will change to floating charging, means the battery charging being finished. 6.The 12V input when automatic charging mode, full electric voltage of 13.8V to 14.3V, about 17V input when manual charging mode, must be artificial monitoring in case of overcharge if manual mode charging, suggest stop charging when the battery beating. Specification: 1. Color: Orange 2. Power Cord Length: 130 cm 3. Clip Cord Length: 60 cm 4. Input Voltage: AC 150-250 V 5.Output Voltage: 12 V /24 V 6. Current: 10 A 7. Frequency: 50-60 HZ 8. Power Supply: US Plug 9. Five Charging Modes: Constant Current Mode/Constant Voltage Mode/Trickle Mode/Floating Mode/No Load Mode 10. Suitable for Battery from 6 AH to 200 AH Note: 1.Do not block cooling hole or use the charger with the cooling fan off. 2.This product is non-waterproof, please avoid the water. Package Included: 1 X Battery Charger 1 X User Manual

12V/24V 8A Touch Screen Pulse Repair LCD Battery Charger Red For Car Motorcycle Package weight: 0.64 kg Description - Microprocessor Control (CPU) - 3-STAGE AUTOMATIC CHARGING: - Automatic charging protects your battery from being overcharged. So you can leave the charger connected to the battery indefinitely. - Suitable for most battery types including Calcium, Gel and AGM, Wet batteries. They may also help restore drained and sulphated batteries. -Types of batteries: Most types of lead acid batteries including Calcium, GEL and AGM, Wet,EFB, etc.. - Switchmode technology - Polarity protection - Output short protection - Non battery link protection - Over voltage protection - Over temperature protection Specification: Input voltage: 100V-265V AC, 50-60Hz Rated output: 12V 8A / 24V 4A Color: Red Minimum start voltage: 2.0V Battery range: 2Ah-150Ah Thermal protect: 65'C+/-5'C Efficiency: App. 85% Output Line Length: 65cm Input Wire Length: 110cm Compliant standards: CB,CE, IEC60335, EN61000, EN55014 Dimension (L×W×H): 170×98×58mm Cooling: Fan Scope of application: 12V/24V 2Ah-150Ah lead-acid batteries/start-up and shutdown batteries(lithium batteries can not be charged.) Note: This Charger is for battery capacity between 2AH to 150AH Pls check the capacity (AH) of your battery before buying the charger! Thanks! Package Included: 1 X 12V/24V Pulse Repair LCD Batteru Charger Click here for more deals 12V/24V 8A Touch Screen Pulse Repair LCD Battery Charger Red For Car Motorcycle 12V/24V 8A Touch Screen Pulse Repair LCD Battery Charger Red For Car Motorcycle

Feature: 1. Can test all cars to start lead-acid batteries, including ordinary lead-acid batteries AGM flat, Battery AGM winding battery colloid batteries and so on. 2. Can be detected directly out of the battery. 3. With polarity reverse polarity protection, clip reverse will not damage the tester, and no heat, no spark will not damage the battery or hurt the body of the operator. 4. Can directly test the loss of battery, no need to be fully charged in the test. 5. Test standards include the world's vast majority of commonly used battery standards, such as CCA / BCI / CA / MCA / JIS / DIN / IEC / EN / SAE / GB, etc. Specification: Shell Material: Acid Acrylonitrile Butadiene Styrene (ABS) Color: Red Size: 12x7cm Voltage range: 12V Range CCA: 100-800 Battery range: 30AH-100AH Operating temperature: -20 ¿¿¿ -50 ¿¿¿ Applicable battery: 12V starting type lead acid battery Special test clip: double conductor Kelvin folder How to use: 1. The tester black and white clip clip to the measured battery, red and black negative, the tester will display the boot interface. The measured voltage is below 6.0V The following can not be normal test; press OK key to continue down 2. Follow the tester prompts, and then select: (1) Input standard selection: refers to the factory standard factory standard, in the battery directly above or can be seen, Select the standard marked on the battery can be, such as CCA, BCI, DIN and so on (2) Rated capacity selection: refers to the battery factory starting current standard, in the battery directly above or before you can see, then press OK button to start testing. Package Included: 1 X Auto Battery Tester

Options: Plug UK plug Plug AU plug Plug EU plug Plug US plug Description - Microprocessor Control (CPU) - 3-STAGE AUTOMATIC CHARGING: - Automatic charging protects your battery from being overcharged. So you can leave the charger connected to the battery indefinitely. - Suitable for most battery types including Calcium, Gel and AGM, Wet batteries. They may also help restore drained and sulphated batteries. -Types of batteries: Most types of lead acid batteries including Calcium, GEL and AGM, Wet,EFB, etc.. - Switchmode technology - Polarity protection - Output short protection - Non battery link protection - Over voltage protection - Over temperature protection Specification: Input voltage: 100V-265V AC, 50-60Hz Rated output: 12V 8A / 24V 4A Color: Red Minimum start voltage: 2.0V Battery range: 2Ah-150Ah Thermal protect: 65'C+/-5'C Efficiency: App. 85% Output Line Length: 65cm Input Wire Length: 110cm Compliant standards: CB,CE, IEC60335, EN61000, EN55014 Dimension (L×W×H): 170×98×58mm Cooling: Fan Scope of application: 12V/24V 2Ah-150Ah lead-acid batteries/start-up and shutdown batteries(lithium batteries can not be charged.) Note: This Charger is for battery capacity between 2AH to 150AH Pls check the capacity (AH) of your battery before buying the charger! Thanks! Package Included: 1 X 12V/24V Pulse Repair LCD Batteru Charger

Description: 1. The MXS 5.0 is an advanced microprocessor controlled battery charger with automatic temperature compensation built in providing unrivalled performance on batteries from 1.2Ah up to 110Ah. 2. The MXS5.0 solves a broad range of battery problems and is the ideal charger for the user with high demands. 3. AGM mode is perfect for maximizing performance and life of most Stop-Start batteries. Feature: 1. Features of the MXS 5.0 include diagnosis of battery condition to establish if it can receive and retain charge, automatic desulphation programmer and a special reconditioning function that will revive and restore deeply discharged and stratified batteries. 2. The built in temperature compensation ensures ideal charging performance even in the most extreme conditions. 3. Float/Pulse maintenance makes the MXS 5.0 ideal for long-term maintenance. The entire process of battery testing, charging and maintenance is easily followed on the clear LED display. 4.The MXS 5.0 is a fully automatic "connect and forget" 12V charger with 8 charging steps. 5.Offers selectable SMALL BATTERY, and NORMAL BATTERY programs. The RECOND and AGM options operate individually or together in both SMALL BATTERY and NORMAL BATTERY programs, providing great flexibility for the user. Wide charging range on all lead-acid battery types from 1.2Ah up to 110Ah with additional maintenance capability to 160Ah. Splash proof and dust proof. The MXS 5.0 is easy and safe to use, protects vehicle electronics, is spark-free, reverse polarity protected and short circuit proof. Specification: Volt 12V Rated Voltage AC 220–240VAC, 50–60Hz Charging voltage SMALL, NORMAL: 14.4V, COLD/AGM: 14.7V, RECOND: 15.8V Minimun battery voltage 2.0V Charging current 5A max Current, mains 0.6A rms (at full charging current) Back current drain Ripple Ambient temperature -20°C to +50°C, output power is reduced automatically at high temperatures Charger type 8 step, fully automatic charging cycle Battery types All types of 12V lead-acid batteries (WET, MF, Ca/Ca, AGM and GEL) Battery capacity 1.2–110Ah up to 160Ah for maintenance Dimensions 150 x 65 x 38mm (L x W x H) Weight 0.6kg User Mannual in ten languages (EN, DE, FR, ES, IT, NL, SE, DK, NO, FI) Package Included: 1 X Charger Unit; 2 X User Manual

Description: 5-STAGE AUTOMATIC CHARGING: This is a fully automatic battery charger with 5 charge stages. Automatic charging protects your battery from being overcharged. So you can leave the charger connected to the battery indefinitely. 5-stage charging is a very comprehensive and accurate charging process that gives your battery longer life and better performance compared to using traditional chargers. 5-stage chargers are suitable for most battery types including Calcium, Gel and AGM, Wet batteries. They may also help restore drained and sulphated batteries. Types of batteries: Most types of lead acid batteries including Calcium, GEL and AGM, Wet Motorcycle: for 2Ah -20AH; Car: for 20AH -100AH 1. Desulphation The Desulphation stage may break down sulphation that occurs in batteries that have been left flat for extended periods of time, returning them back to full charge. sulphation occurs when lead-sulphate hardens and clogs up the battery cells.   2. Bulk (Constant Current) Bulk mode charges the battery at the maximum rate (constant current) putting a large amount of power into the battery in a short amount of time. This stage will charge the battery to approximately 60%, until the voltage reaches 14.7 volts for 12V charger   3. Absorption (Constant Voltage) The charge rate slows down so the battery can absorb more power and reach 80% charge. The voltage remains at a constant 14.7 volts for 12V charger while the current is gradually reduced until no more power can be added without over-charging the battery.   4. Float The Float stage maintains the battery at 100% charge without overcharging or damaging the battery. This means the charger can be left connected to the battery indefinitely.   5. Stop - The Charger stop charging and cut-off output.   Specification: Switchmode technology: Yes Polarity protection: Yes Output short protection: Yes Non battery link protection: Yes Over voltage protection: Yes Over temperature protection: Yes Cooling: Natural convection Input voltage: 100-240V AC, 50-60Hz Rated output: 12V DC, 0.8A/3.6A Minimum start voltage: 8.0V The 5 stages are: Desulphation; Bulk; Absorption; Float, Auto-cut off Battery range: 2A-100Ah Thermal protect: 65'C+/-5'C Efficiency: App. 85%. Compliant standards: CB,CE, IEC60335, EN61000, EN55014 Dimension (L×W×H): 170×65×40mm AC cable length: About 1.5m DC cable length: About 1.4m We will send you an AU Adapter   Package Included: 1 X Battery Smart Charger with AC & DC Cable 1 X User Manual  

T16897 12V Digital Battery Alternator Tester with 6 LED Lights Display Car Vehicle Diagnostic Tool Features: ﾡ￱ Alternator state check. ﾡ￱ Battery state check. ﾡ￱ Battery overload display. ﾡ￱ 6-LED display, clearly present the alternator and battery state. ﾡ￱ Two testing clips for safe and easy operation. ﾡ￱ Small size and light weight, convenient to carry. ﾡ￱ Fit for car, motorcycle, etc. ﾡ￱ Suitable for 12V lead acid batteries, hardtop batteries, discharge batteries and maintenance free batteries heavy duty insulated clamps. ﾡ￱ Easy and safe to use, no sparking. ﾡ￱ With a good chip inside, not easy to get hot on the surface. 6 LED Lights: ﾡ￱ Alternator state check: First light (red): Fault Second light (green): Good Third light (green): Full ﾡ￱ Battery state check: First light (yellow): Middle Second light (red): Low Third light (green): OK Specifications: ﾡ￱ LED quantity: 6 (2 red, 3 green, 1 yellow) ﾡ￱ Material of wire: 0.06 square millimeter copper ﾡ￱ Max. voltage / current: 12V / 15A ﾡ￱ Length of wire: 250mm Features: Portable Functions: Improve driving safety Material: Plastic,Copper Color: Gray Package weight: 0.139 kg Product size (L x W x H): 12 x 5 x 1.5 cm / 4.72 x 1.97 x 0.59 inches Package size (L x W x H): 25 x 14.5 x 2.5 cm / 9.83 x 5.70 x 0.98 inches Package Contents: 1 x T16897 12V Digital Battery Alternator Tester 6 LED Lights Display Indicates Condition

*FREE SHIPPING* 12V Car Battery & Alternator Tester   Main Feature - Alternator state check. - Battery state check. - Battery overload display. - 6-LED display, clearly present the alternator and battery state. - Two testing clips for safe and easy operation. - Small size and light weight, convenient to carry. - Fit for car, motorcycle, etc. - Suitable for 12V lead acid batteries, hardtop batteries, discharge batteries and maintenance free batteries - Heavy duty insulated clamps. - Easy and safe to use, no sparking. - With a good chip inside, not easy to get hot on the surface.   Specifications: LED quantity: 6 (2 red, 3 green and 1 yellow) Material of wire: 0.06square millimeter copper Max. voltage and current: 12V 15A   6 LED Lights:    Alternator state check: First light (red): Fault Second light (green): Good Third light (green): Full    Battery state check: First light (yellow): Middle Second light (red): Low Third light (green): OK   Package includes: 1 x Battery Tester with Two Clips    

Description: 4-stage microprocessor controlled. Professional automatic switch mode. For charging AGM, GEL, SLA and Wet batteries. Overheat, overcharge, short circuit&reverse polarity protection. Specification: Input Voltage: 110V-240V Output Voltage: 12V Rated Frequency: 50-60HZ Charger Current: 5A Plug: US plug (Send an adapter according to your country) Charge Principle: Auto 4 stages: Ud-Uo-Up Working Temperature: -15~+50 ￢ﾄﾃ Enclosure: IP65 Dimension: Approx. 14.5x7x5.5cm/ 5.71x2.76x2.17" Package Included: 1 X Battery Charger