10pcs module
Top sales list 10pcs module
South Africa (All cities)
10Pcs Slot Socket Reader SD Card Module For Mp3 Arduino Compatible 10Pcs Slot Socket Reader SD Card Module For Mp3 Arduino CompatibleDescription:Make your SD application more easier and simpleIt is easily interfaced as a peripheral to your arduino sensor shield moduleThrough programming, you can read and write to the SD card using your arduinoCan be used for SD Card more easily, such as for MP3 Player, MCU/ARM system controlWith all SD SPI Pins out: MOSI, SCK, MISO and CS,for further connectionInput Voltage: 3.3V/5VSpecification:Item size:51x304mmNet weight: 8gPackaging weight: 18gColor: BluePackage included:10 X SD card module
R 230
See product
South Africa
10Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 10 x Micro SD TF card module
See product
South Africa (All cities)
10Pcs HY-SRF05 Ultrasonic Distance Sensor Module Measuring Sensor Module Description: This module performance is stable, measure the distance accurately. Module precision, blind spots (2cm) super close. Specification: Input voltage: 5V DC Quiescent current: Output level(high): 5V Output level(low): 0V Induction angle: Detection distance: 2cm - 450cm Accuracy: up to 0.3cm Blind spots: 2cm Package included: 10 x HY-SRF05 ultrasonic distance sensor module
R 346
See product
South Africa (All cities)
10Pcs Soil Hygrometer Humidity Detection Moisture Sensor For Arduino Description: This is a summary of the soil moisture sensor can be used to detect moisture, when the soil is dry, the module outputs a high level, whereas output low. Using this sensor make an automatic watering system, so that your garden plants without people to manage. Operating voltage: 3.3V~5V. Adjustable sensitivity (shown in blue digital potentiometer adjustment) Dual output mode,analog output more accurate. A fixed bolt hole for easy installation. With power indicator (red) and digital switching output indicator (green). Having LM393 comparator chip, stable. Panel PCB Dimension: 3cm x 1.5cm. Soil Probe Dimension: 6cm x 2cm. Cable Length: 21cm. VCC: 3.3V-5V. GND: GND. DO: digital output interface(0 and 1). AO: analog output interface. Instructions for Use: 1. Soil moisture module is most sensitive to the ambient humidity is generally used to detect the moisture content of the soil. 2. Module to reach the threshold value is set in the soil moisture, DO port output high, when the the soil humidity exceeds a set threshold value, the module D0 output low. 3. The digital output D0 can be connected directly with the microcontroller to detect high and low by the microcontroller to detect soil moisture. 4. The digital outputs DO shop relay module can directly drive the buzzer module, which can form a soil moisture alarm equipment. 5. Analog output AO and AD module connected through the AD converter, you can get more precise values of soil moisture. Package Included: 10 x Soil moisture detector module 10 x Probe 10 x 2P Jumper Cable
R 204
See product
South Africa (All cities)
10Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load: AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 10 x 1 Channel H/L level trigger optocoupler relay module
R 346
See product
South Africa
10Pcs MB102 Breadboard Module Adapter Shield 3.3V/5V For Arduino Board Description: Breadboard power supply module, compatible with 5 V, 3.3 V Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: Fluctuation two road independent control, can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient external lead use. Size: 5.3*3.2*2.5cm Weight: 12g Please notice: this item only a Power Supply Module, Breadboard is not included. Package included: 10 x Power supply module Breadboard power supply module, compatible with 5 V, 3.3 V.
R 229
See product
South Africa
10Pcs 1100 Meter Long Distance NRF24L01+PA+LNA Wireless Module Board With Antenna Desription: NRF24L01P + PA + LNA Division for the ultra-long-distance data transmission, specially developed high-power and high sensitivity wireless module 2.4G ISM band NRF24L01P + PA + LNA wireless module to work in the license-free that can be point-to-point applications or be composed of a star network. Digital transmission chip NRF24L01+ with the Division of Professional Design professional full two-way RF power amplifier high power PA and LNA chip, RF switches and band pass filters, makes effective communication distance greatly expand. RF part, it has been done a lot of optimization matching debugging. The emission efficiency to achieve the highest harmonic minimum and make NRF24L01P + PA + LNA wireless module of RF interference to the external equipment reaches minimum, while not susceptible to interference from other devices. NRF24L01P + PA + LNA wireless module integration is extremely high, the size is 41mm x 15.5mm to make conveniently embedded. Package included: 10 x 1100 Meter Long Distance NRF24L01+PA+LNA Wireless Module Board With Antenna
R 771
See product
South Africa (All cities)
10Pcs NRF24L01+ SI24R1 2.4G Wireless Power Enhanced Communication Receiver Module 10Pcs NRF24L01 SI24R1 2.4G Wireless Power Enhanced Communication Receiver Module Description:NRF24L01 SI24R1 is fully compatible (SPI operation timing, registers, definitions, state diagram), can communicate with each other, support NRF24L01 all communications. Default mode output power of SI24R1 is 2 ~ 3dBm, if you want the output is 7dBm, you should write 1 (NRF24L01 This bit is not used, the default is 0) into the lowest bit register address 0x06 (RF_SETUP). For example, the 01register, 0x061111.Pacakge included:10 x Wireless Power Enhanced Communication Receiver Module
R 330
See product
South Africa (All cities)
10Pcs 3W LED Module High Power Module For Arduino Feature: Color temperature: Warm White 3000-3200K / white 6000-6500K Forward current: 700MA Luminous flux: White 180-200LM (lumens), Red 90-100LM (lumens), Green 80-90LM (lumens) Forward voltage: 3.3 - 3.6 V Reverse voltage: 5V Power: 3W Viewing angle: 180° Working temperature: -20° to 60° Storage temperature: 20° to 60° Package included: 10 x LED module
R 297
See product
South Africa (All cities)
10Pcs KY-016 RGB 3 Color LED Module For Arduino Red Green Blue Description: This is RGB 3 color LED module for Arduino red green blue Brand: KEYES Module: KY-016 Material: PCB RGB signal output 3 color: Red, green, blue Compatible with Arduino DIY project Package included: 10 x RGB 3 color LED module
R 109
See product
South Africa (All cities)
10Pcs Mini 1A Lithium Battery Charging Module Board With USB Interface Description: Charging method: linear charge 1% Charging current: 1A adjustable Charge accuracy: 1.5% Input voltage: 4.5V-5.5V Full charge voltage: 4.2V Charging indicator: Red charging green full charge Charging input interface: Mini USB Working temperature: -10C to +85C Reverse: NO Size: 25 x 19 x 10mm Note: Ampere meter can only be connected to 5V input end of the module. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough. The connection wire should not be too long. Make sure the connect point is good. If the input voltage is too high, like 5.2V, the current will be less than 1000mA, it is normal. It is protection function, Auto-substract the charging current to avoid burn damage to chip. Input reverse has no effect on the chip, but the output (battery terminals) reverse will burn chips. Applications: This module is used for single-or multi-section parallel lithium lithium rechargeable battery, charging from the USB port to take power. Package included: 10 x 1A lithium battery charging module
R 288
See product
South Africa (All cities)
10Pcs Speed Measuring Sensor Counter Motor Test Groove Coupler Module For Arduino Application: Widely used in motor speed detection, pulse count, the position limit, etc. Feature: Using imported groove optical coupling sensor, width 5mm. It have the output state light, if output high level, the lights are off. if output low level,it on. If it covered,it will output high level;otherwise it output low level. Good signal and waveform, with strong driving ability for more than 15mA. The working voltage of 3.3V to 5V. Output: digital switch output (0 and 1). Equipped with a fixed bolt hole, easily install. Small board PCB size: 3.2 cm x 1.4 cm. Use the LM393 wide voltage comparer. Specification: The DO output interface can be directly connected to a micro-controller IO port, if there is a block detection sensor, such as the speed of the motor encoder can detect. DO modules can be connected to the relay, limit switch, and other functions, it can also with the active buzzer module, compose alarm. Wiring specification: VCC Connect the positive 3.3 5 v power supply GND Connect power negative DO TTL switch signal output AO This module does not work Package included: 10 x Speed Measuring Sensor Module
R 205
See product
South Africa (All cities)
10Pcs Transparent Acrylic Shell Module Case For Arduino UNO R3 Module Board
R 560
See product
South Africa (All cities)
10pcs JDY-10 Bluetooth 4.0 Module BLE Bluetooth Serial Port Module Compatible With CC2541 Slave Package contains 1 X item of the smallest listed variant.
R 730
See product
South Africa (All cities)
10pcs DC-DC 9V 3A Power Supply Module Buck Step Down Regulator Module 24V 18V 12V To 9V Fixed Output Package contains 1 X item of the smallest listed variant.
R 430
See product
South Africa (All cities)
10Pcs I2C RTC DS1307 AT24C32 Real Time Clock Module For AVR ARM PIC SMD Description: 24C32 32K I2C EEPROM memory Using LIR2032 rechargeable lithium battery with charging circuit Solve the problem of no literacy of the DS1307 with backup battery Support timing 1 year of the DS1307 after fully charged Leads to the DS1307 clock pin provides a clock signal for the microcontroller Other I2C devices can be cascaded Size: 27 x 28 x 8.4mm Note: Because of shipping restrictions, we won't ship battery Package included: 10 x DS1307 module (battery is not included)
R 177
See product
South Africa (All cities)
10Pcs WTV020 Audio Module MP3 Player With MicroSD Card Reader For Arduino Feature: Use the WTV020SD MP3 player, to play recorded audio files for a custom voice for a robot, use it as a tiny music player. This module has a small, simple IC for embedding audio-playback into your next project. It even has the ability to activate 512 unique sound files. Characteristics: 6Khz to 36Khz / micro-SD (FAT) 64Mb to 2Gb / 8.0uA / DC 3.3V / WTV020SD Package includes: 10 x MP3 Player WTV020 With Micro-SD Reader
R 740
See product
South Africa (All cities)
10Pcs 5V-60V To 1.25V-30V LM2576HV DC-DC Step Down Module Feature: Item No: lll-0005 IN +: Input + IN-: input negative OUT+: Output + OUT-: output negative Input voltage range: 5V-60V (Suggestion: 50V or less) Output voltage range: 1.25V-26V Maximum output current: 3A Continuous current: 1.2A (total output power less than 20W) Dimensions: 4.3cm * 3.0cm * 1.2cm (L * W * H) Input: 56V Output: 12V 1A Input: 48V Output: 24V 1A Package included: 10 x DC-DC Step Down Module
R 650
See product
South Africa (All cities)
10Pcs DS18B20 DC 5V Digital Temperature Sensor Module For Arduino Features: It's easy to install with mounting holes, diameter of the hole is 2.5m. Digital signal output 18B20 Temperature Sensor Chip Resolution adjustment ranges from 9-12 bytes. Operating current: DC5V. Temperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C. Size: 28 x 12 x 10 mm Weight: 2g Package included: 10 x DS18B20 digital temperature sensor module
R 378
See product
South Africa (All cities)
10Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module Description: You’ve always wanted to output analog voltages from a microcontroller, the MCP4725 is the DAC that will let you do it! The CJMCU-MCP4725 is an I2C controlled Digital-to-Analog converter (DAC). A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller. Digital to analog converters are great for sound generation, musical instruments, and many other creative projects! This version of the CJMCU-MCP4725 Breakout fixes a few issues with the board including the IC footprint, the I2C pinout, changes the overall board dimensions to better fit your projects, and a few more minor tweaks. This board breaks out each pin you will need to access and use the MCP4725 including GND and Signal OUT pins for connecting to an oscilloscope or any other device you need to hook up to the board. Also on board are SCL, SDA, VCC, and another GND for your basic I2C pinout. Additionally, if you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this. Feature: 12-bit resolution I2C Interface (Standard, Fast, and High-Speed supported) Small package 2.7V to 5.5V supply Internal EEPROM to store settings Package included: 10 x CJMCU-MCP4725 I2C DAC Breakout Development Board Module
R 260
See product
South Africa (All cities)
10Pcs 5V 700mA 3.5W AC-DC Step Down Isolated Switching Power Supply Module Feature: Input voltage: AC 85 ~ 265v 50 / 60HZ or DC100v-370v Output voltage: DC5V (± 0.2V) Output Current: 700mA Power: 3.5W Package included: 10 x 5V 700mA 3.5W AC-DC Step Down Isolated Switching Power Supply Module
R 330
See product
South Africa (All cities)
10Pcs Transparent Acrylic Shell Box For Arduino UNO R3 Module Board Feature: With EN instructions. Weight: 53g Dimensions: 79.5 x 64.5 x 21mm Material: A grade acrylic sheet For Arduino UNO R3 Development Board only Note: The UNO R3 module is not included. Package included: 10 x Transparent Acrylic Shell
R 336
See product
South Africa (All cities)
10Pcs DC-DC 12V to 3.3V/5V/12V Voltage Converter Power Supply Module Feature:One channel input: DC 6V - 12V (the input voltage must be higher than the output voltage to 1V or more.)Triple output: 3.3V (ﾱ 0.05v error), 5V (ﾱ 0.05v error), 800mA (load current can not exceed 800ma), 12V (12V input directly to the output)Specially designed two rows of needle fixing hole, can be directly fixing on the plate to extend the experiment;Using multiple input and output pin, easy to use and connect;PCB board size: 4.5 x 4.5cmWith power indicator (red)Package includes:10 x Multi-output Power Supply Module
R 310
See product
South Africa (All cities)
10Pcs Rain Sensor Water Level Measure Module Raindrop Analog Sensor Board
R 430
See product
South Africa (All cities)
10Pcs TEA5767 76-108MHZ FM Stereo Radio Module With Antenna For Arduino
R 1.720
See product
South Africa (All cities)
10Pcs I2C WiiChuck Nunchuck Small Adapter Shield Module Board For Arduino
R 370
See product
South Africa (All cities)
10Pcs XH-M400 Step Down Module Adjustable XL4016E1 High Power DC-DC 8A DC4-40V With Regulator
R 960
See product
South Africa (All cities)
10Pcs 3A XL6009 DC-DC 50KHz Adjustable Step-up Power Converter Module Specification: Wide Input voltage: 3V-30V Output Voltage: 4-35V (Adjustable) Output current: rated current 3A MAX (Heat-sink Needed) If you need its output power greater than 15W, please add with heat-sink Conversion efficiency: Up to 92% (output voltage higher, the higher the efficiency) Switching Frequency: 50KHz Rectifier: Non-Synchronous Rectification Short circuit protection: current limiting, since the recovery Operating temperature: Industrial grade (-40 to +85) (output power 10W or less) Full load temperature rise: 40 Load regulation: 0.5% Voltage regulation: 0.5% Size:47 x 26 x 15 mm Package included: 10 x XL6009 DC-DC 50KHz Adjustable Step-up Power Converter Module
R 480
See product
South Africa (All cities)
10pcs BESTEP 1 Channel 5v Relay Module High And Low Level Trigger For Arduino Package contains 1 X item of the smallest listed variant.
R 440
See product
South Africa (All cities)
10Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Package contains 1 X item of the smallest listed variant.
R 410
See product
-
Next →
Visit our blog
Share on Facebook
Share on Twitter