10pcs dc 1v 5v

10Pcs DC 5V 4 Phase 5 Wire Stepper Motor With ULN2003 Driver Board Description: This is 28YBJ-48 DC 5V 4 phase 5 wire stepper motor with ULN2003 driver board 5-wire phase can drive ordinary uln2003 chip can also be connected as phase 2 may be supporting the development board, direct plug, easy to use stepper motor used in the development board Motor: Diameter: 28mm Voltage: 5V Step angle: 5.625 x 1/64 Reduction ratio: 1/64 ULN2003 driver board: A, B, C, D LED indication Four-phase stepper motor work status Size: 31mm x 35mm Package included: 10 x ULN2003 driver board 10 x 28BYJ-48 stepper motor

10pcs DC 5V DIY Electronic Windmill Training Kit Speed Adjustable MCU Course Design For Soldering

Buy 10pcs DD1205UA DC to DC 1.5V 3V 3.3V 3.7V 6V to 5V DC Buck Boost Converter for R676.62

Buy 10pcs DD1205UA DC to DC 1.5V 3V 3.3V 3.7V 6V to 5V DC Buck Boost Converter Step Up Down Voltage Conv for R652.00

Buy 10pcs Blue 0.56 Inch Mini Digital Voltmeter DC 4.5V To 30V Digital Voltmeter Voltage Panel Meter For for R445.00

Buy 10pcs DC 5V Step Up Boost Converter Voltage Regulate Power Supply Module Board for R531.07

Buy 10pcs Green 0.56 Inch Mini Digital Voltmeter DC 4.5V To 30V Digital Voltmeter Voltage Panel Meter Fo for R402.85

Specifications:   Operating voltage: DC4.5V-35V Output current: 0-5A Output power: 90W (max) Quiescent current: 7uA (standby) PWM duty cycle: 1% -100% PWM frequency: 20khz Size: 30mm x 26mm x 14mm    Precautions:   -DC motor governor input is DC, can not directly connected to the AC (for example: home 220V AC), otherwise it will burn! -DC power supply positive and negative terminals do not reverse, otherwise the governor may be damaged. -The motor can be positive or negative, when the direction of operation and expectations do not match, you can adjust the line order to change the direction. -Adjust the potentiometer knob to change the governor output duty cycle, the motor speed changes.   Package Included:   10 x PWM DC Motor Speed Controller

Description: Working voltage: DC 5V Work effect: speed can be adjusted Size: 40 x 50mm Note: it is not soldering finished product, it is diy kit. Circuit principle:   The circuit is based on the control of the microcontroller, the microcontroller controls the vertical LED lit, so as to achieve the effect of a windmill rotation, you can change the speed of the windmill flashing through the button. Package included: 10 x DIY windmill training kit

10Pcs DC-DC 12V to 3.3V/5V/12V Voltage Converter Power Supply Module Feature:One channel input: DC 6V - 12V (the input voltage must be higher than the output voltage to 1V or more.)Triple output: 3.3V (ﾱ 0.05v error), 5V (ﾱ 0.05v error), 800mA (load current can not exceed 800ma), 12V (12V input directly to the output)Specially designed two rows of needle fixing hole, can be directly fixing on the plate to extend the experiment;Using multiple input and output pin, easy to use and connect;PCB board size: 4.5 x 4.5cmWith power indicator (red)Package includes:10 x Multi-output Power Supply Module

10Pcs MB102 Breadboard Module Adapter Shield 3.3V/5V For Arduino Board Description: Breadboard power supply module, compatible with 5 V, 3.3 V Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: Fluctuation two road independent control, can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient external lead use. Size: 5.3*3.2*2.5cm Weight: 12g Please notice: this item only a Power Supply Module, Breadboard is not included. Package included: 10 x Power supply module Breadboard power supply module, compatible with 5 V, 3.3 V.      

10Pcs Geekcreit DC 5V 3MM x 10MM WS2812B SMD LED Board Built-in IC-WS2812

10Pcs DS18B20 DC 5V Digital Temperature Sensor Module For Arduino Features: It's easy to install with mounting holes, diameter of the hole is 2.5m. Digital signal output 18B20 Temperature Sensor Chip Resolution adjustment ranges from 9-12 bytes. Operating current: DC5V. Temperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C. Size: 28 x 12 x 10 mm Weight: 2g Package included: 10 x DS18B20 digital temperature sensor module

10Pcs 5V 16M ATmega328P Arduino Compatible Version LilyPad 328 Main Board Description: The Arduino Compatible LilyPad is a microcontroller board designed for wearables and e-textiles. It can be sewn to fabric and similarly mounted power supplies, sensors and actuators with conductive thread. The board is based on the ATmega328 with the Arduino bootloader. The main board has a minimum number of external components to keep it as small (and as simple) as possible. The latest version supports automatic reset for even easier programming. The back side of the LilyPad is completely flat. It uses a surface mount programming connector, which keep the header from poking through. Specification: Microcontroller: ATmega328P Operating voltage: 2.7V ~ 5.5V (recommended 5V) Input voltage: 2.7V ~ 5.5V (recommended 5V) Digital I/O pins: 14 (of which 6 provide PWM output) Analog input pins: 6 DC current per I/O pin: 40mA Flash memory: 16KB (of which 2KB used by bootloader) SRAM: 1KB EEPROM: 512bytes Clock speed: 16MHz Note: Don't power the LilyPad Arduino with more than 5.5V, or plug the power in backwards: you'll kill it. Package included: 10 x Arduino compatible LilyPad ATmega328P

10Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load:  AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 10 x 1 Channel H/L level trigger optocoupler relay module