10pcs 78m12 mini voltage

Buy 10pcs 78M12 Mini Voltage Regulator Module with Pin High Accuracy Low Power Cons for R268.47

Buy (Voltage 12V)78M05 78M06 78M09 78M12 Mini Voltage Regulator Module with Pin High Accuracy Low Po... for R149.00

Buy 10pcs 78M05 Mini Voltage Regulator Module with Pin High Accuracy Low Power for R219.00

10Pcs ATTINY85 Mini Usb MCU Development Board For Arduino Feature: 8K Byte of In-System Programmable Program Memory Flash 512 Bytes In-System Programmable EEPROM 512 Bytes Internal SRAM 1.8-5.5V work voltage Support SPI/TWI communication Low power consumption Package included: 10 x ATTINY85 Mini Usb MCU Development Board For Arduino

Buy 10pcs Blue 22MM AD16 AD16-22DSV Type AC 60-500V Mini Voltage Meter LED Digi for R359.00

Buy 10pcs 7W Mini DC DC Boost Step Up Converter 2.6-5.5V to 5V Voltage Regulator Module for R416.98

10Pcs Mini 1A Lithium Battery Charging Module Board With USB Interface Description: Charging method: linear charge 1% Charging current: 1A adjustable Charge accuracy: 1.5% Input voltage: 4.5V-5.5V Full charge voltage: 4.2V Charging indicator: Red charging green full charge Charging input interface: Mini USB Working temperature: -10C to +85C Reverse: NO Size: 25 x 19 x 10mm Note: Ampere meter can only be connected to 5V input end of the module. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough. The connection wire should not be too long. Make sure the connect point is good. If the input voltage is too high, like 5.2V, the current will be less than 1000mA, it is normal. It is protection function, Auto-substract the charging current to avoid burn damage to chip. Input reverse has no effect on the chip, but the output (battery terminals) reverse will burn chips. Applications: This module is used for single-or multi-section parallel lithium lithium rechargeable battery, charging from the USB port to take power. Package included: 10 x 1A lithium battery charging module

Feature:   Input voltage DC4.5-25V, 600mA output current capability per channel 1.2A PEAK output current(non repetitive) per channel Enable facility Overtemperature protection Logical "0" input voltage up to 1.5 V(HIGH NOISE IMMUNITY) Internal clamp diodes   Description:   The Device is a monolithic integrated high voltage, high current four channel driver designed to accept standard DTL or TTL logic levels and drive inductive loads (such as relays solenoids, DC and stepping motors) and switching power transistors. To simplify use as two bridges each pair of channels is equipped with an enable input. A separate supply input is provided for the logic, allowing operation at a lower voltage and internal clamp diodes are included. This device is suitable for use in switching applications at frequencies up to 5 kHz. 9-24V motor drive wiring: 5V motor drive wiring: Package included: 10 x MINI L293D Arduino Motor Drive Expansion Board  

Buy 10Pcs Mini DC-DC1.3A Voltage Converter Step Down Module 12V 24V to 5V 3.3V 9V w for R224.57

Buy 10pcs Green LED 22mm DC Voltage Measuring Instrument Mini Voltagemeter for R334.73

Buy 10pcs Blue 0.56 Inch Mini Digital Voltmeter DC 4.5V To 30V Digital Voltmeter Voltage Panel Meter For for R445.00

Buy 10pcs Mini DC 3.5-6V to 3.3V DC-DC Converter Step Down Buck Regulator LDO Module Voltage regulato... for R289.00

Buy 10Pcs Geekcreit Red Led 0.28 Inch 2.5V-30V Mini Digital Volt Meter Voltage Tester Voltmeter for R240.16

Buy 10pcs Mini 2A DC DC Buck Converter 3.3-5.5V to 3.3V Module Step Down Voltage Regulator Module... for R419.00

Buy 10Pcs Geekcreit White 0.28 Inch 3.0V-30V Mini Digital Volt Meter Voltage Tester for R581.00