10a full

MPPT SOLAR CHARGE CONTROLLER   1. SAFETY Full consideration to the safety of persons and property has been given when designing the products. However the incorrect connection may cause the system breakdown or even safety accident. For your safety and benefits, the following rules must be complied during the operation.. Installation of this product shall be tinder the guidance of the professionals in this field.. Prevent this controller from water, humidity and insects, to avoid short-circuit.. Keep children and incapable persons away from the controller. Keep the controller away from electrical heater, heating machine and other high temperature electrical appliances; avoid the controller suffering from insulation directly.. Please check the rated voltage of solar panel, battery, and loads before connection. 12V rated voltage is 12V, 24V rated voltage is 24V, 48V rated voltage is 48V.. Make sure connections between positive and negative poles of Solar panels, Battery and Loads are correct.. The diameter of connecting cable must be matched with the requirements of the current. Do not use thinner diameter cable, the thinner diameter. The larger resistance, this will cause higher temperature and output power decreasing.. The total rated current of solar panel and loads must be smaller than the rated current of the controller.. Components of system must be correctly and firmly connected. Prevent the terminals from oxidation and moldy, to avoid connection trouble.   2. FEATURES. MPPT solar charge controller MPPT: Compared with normal solar charge controller, this MPPT controller could increase efficiency by %.. This controller can charge and discharge at the same time.. This MPPT controller has perfect SOC function, control charge current, and supply power to the loads. Function:. Always keep the battery on fill voltage condition.. Prevent the battery from over-charging.. Prevent the battery from over-discharging.. Prevent the battery from reverse charging to solar panels during nights.. Reverse Polarity Protection for Battery. Reverse Polarity Protection for Solar Panels. When the battery voltage is low, the controller will automatically cut off the load from the system. If the voltage of battery is back to normal and the load will restart working.. Thunder protection. According to the battery voltage grade, the controller can automatically set charge-off voltage, the load-off voltage, the load- restore voltage. (The parameter is default under 25 ℃ condition, locked by the CPU procedure, cannot adjust.). The controller will automatically compensate the temperature of the charging voltage according to the changes of ambient temperature.      Warning: Before connecting to the solar panel, please connect the controller to the battery; do not use solar panel supply power to the loads directly. Notes: Do not use lamplight to charge the solar panel (lamplight is too weak to charge) DC power source to replace the solar panel will cause troubles to controller. Choose the suitable wire which diameter should not be too small, please refer to the parameter.   4. INDICATE LIGHT AND BUTTON. When Red LED (CHARGE) is on, battery is charged up strongly; When Red LED is flickering, battery is MPPT charged up in constant voltage; when Red LED is oft charge off. When Green LED (LOAD) is on, loads are working; when Green LED (LOAD) is off, loads stop working.. Three Color-changing LED (BATTERY), When light is red, it indicates low voltage, green indicate battery full charged, orange indicate normal status. Color-changing LED working voltage indicates area: Click here for Specs

CLEARANCE SALE BEST QUALITY PRODUCT AND BEST PRICE!!! DON'T MISS OUT!!!DON'T BE LATER!!! PLEASE BE ADVISED THAT OUR PRICE INCLUSIVE VAT.PRODUCT SPECIFICATIONS POWER: 10A VOLTAGE: 12V024V WEIGHT: 0.39 DIMENSION: FEATURES AND FUNCTIONS adopts industrial degree MCU and SCM and especially software,reach intelligent control solar panel short circuit LED indication for battery capacity High precision voltage recognition function Load output resume,output over-current and output short circuit protrctions Battery reverse connection,over-voltage and low-voltage protections we also stock solar panels, charge controllers,Inverters, batteries LED downlights and many more..... Please inquire about our prices, we will send you the full catalogue. CHANGE ALL OF THOSE HALOGEN LIGHT INSIDE YOUR HOUSE HOLDS OR WORK ENVIRONMENT AND PUT LED PRODUCTS.YOU WILL BE SAVING UP TO 90% OF ENERGY AND YOUR ELECTRICITY BILL WILL DROP WITH A HUGE AMOUNT FEEL FREE TO INQUIRE ABOUT ALL OUR LED PRODUCTS AND WE WILL FORWARD YOU OUR PRICE LIST, BUY CERTIFIED PRODUCTS AT A VERY AFFORDABLE PRICES. CONTACT UMBANI-SOLAR TODAY TO PLACE YOU’RE ORDER ON: LANDLINE: FEEL FREE TO COME TO OUR SHOW ROOM IN CENTURION AND SEE WHAT WE MEAN WITH GOOD PRODUCTS & GOOD PRICES

BEST QUALITY PRODUCTS AND BEST PRICES!!! DON'T MISS OUT!!!DON'T BE LATE!!! -PLEASE NOTE THAT OUR PRICES ARE INCLUSIVE OF VAT ADDED (TAX) PRODUCT SPECIFICATIONS POWER: 10A VOLTAGE: 12V024V WEIGHT: 0.39 DIMENSION: FEATURES AND FUNCTIONS adopts industrial degree MCU and SCM and especially software,reach intelligent control solar panel short circuit LED indication for battery capacity High precision voltage recognition function Load output resume,output over-current and output short circuit protrctions Battery reverse connection,over-voltage and low-voltage protections we also stock solar panels, charge controllers,Inverters, batteries LED downlights and many more..... Please inquire about our prices, we will send you the full catalogue.PLEASE CONTACT US,OUR PROFESSIONAL TECHNICAL TEAM ARE WAITING FOR YOUR QUERIES AND SOLVE YOUR ELECTRICITY DEMANDS. WE VALUE OUR CLIENT WITH INTEGRITY AND WE PROMISE TO TREAT YOU WITH A SMILE,HONESTLY AND RESPECT. PLEASE BE ADVISED THAT WE DO INSTALLATION AS WELL. PHONE US,EMAIL US,CONTACTS US OR VISIT OUR SHOWROOM TEL:/ DIRECT LINE:(012) TRADING HOURS MON-FRIDAY: to SATURDAY: to Sunday:closed Public Holiday:closed VISIT OUR SHOWROOM IN CENTURION AND SEE WHAT WE MEAN WITH GOOD PRODUCTS & GOOD PRICES PRICES ARE SUBJECTS TO CHANGE WITHOUT PRIOR NOTICE DUE RAND/DOLLAR FLUCTUATION.

T10 PWM LCD 10A 12V/24V Solar Panel Battery Regulator Charge Controller Three Time Interval Description: This is a three-time controller into the evening (evening) working time, an interval of rest or pause time, Dawn working time (morning light function), the user can according to their needs, set a different time. T10 10A solar controller applied to the solar photovoltaic system which is used to coordinate solar panels, storage battery and load. It is a very important assembly in the photovoltaic system. It is different from other solar controllers that it is add the comprehensive protection function makes the whole solar photovoltaic system operate efficiently and safely. T10 10A solar controller can adjust automatically the working voltage of solar panels, which can make solar panels work consistently in the maximum power point of the V-A characteristic curve in a whole day. Compared with common solar controllers, it is equipped with temperature compensation function, can make the work efficiency of photovoltaic modules increased by 30%, and can observably prolong the life of the storage battery. Compatible with 260W(24v) solar panel with dark activated function, Max current is 10A. Timer Intigrated (Lighting function). Features: T10 Series controller has the following features: Compared with normal solar charge controller, this MPPT controller could increase efficiency by 10%-30% Solar LCD series a kind of intelligent, multipurpose solar charge and discharge controller. 1. LCD screen display. 2. Easy operation interface. 3. PWM charging mode. 4. Parameter user can reset. 5. A key to open and close the load. 6. A key to restore the factory settings. 7. Battery reverse discharge protection. 8. Battery reverse polarity protection. 9. Battery under voltage protection. 10. Overload, short-circuit protection. 11. Automatic temperature compensation function. 12.Can charge and discharge at the same time, always keep the battery in full status. Package included: 1 x T10 10A PWM Solar Controller 1 x English User Manual 1 x Temp Sensor Detail Pictures: T10 PWM LCD 10A 12V/24V Solar Panel Battery Regulator Charge Controller Three Time Interval

Description: This is a three-time controller into the evening (evening) working time, an interval of rest or pause time, Dawn working time (morning light function), the user can according to their needs, set a different time. T10 10A solar controller applied to the solar photovoltaic system which is used to coordinate solar panels, storage battery and load. It is a very important assembly in the photovoltaic system. It is different from other solar controllers that it is add the comprehensive protection function makes the whole solar photovoltaic system operate efficiently and safely. T10 10A solar controller can adjust automatically the working voltage of solar panels, which can make solar panels work consistently in the maximum power point of the V-A characteristic curve in a whole day. Compared with common solar controllers, it is equipped with temperature compensation function, can make the work efficiency of photovoltaic modules increased by 30%, and can observably prolong the life of the storage battery. Compatible with 260W(24v) solar panel with dark activated function, Max current is 10A. Timer Intigrated (Lighting function). Features: T10 Series controller has the following features: Compared with normal solar charge controller, this MPPT controller could increase efficiency by 10%-30% Solar LCD series a kind of intelligent, multipurpose solar charge and discharge controller. 1. LCD screen display. 2. Easy operation interface. 3. PWM charging mode. 4. Parameter user can reset. 5. A key to open and close the load. 6. A key to restore the factory settings. 7. Battery reverse discharge protection. 8. Battery reverse polarity protection. 9. Battery under voltage protection. 10. Overload, short-circuit protection. 11. Automatic temperature compensation function. 12.Can charge and discharge at the same time, always keep the battery in full status. Package included: 1 x T10 10A PWM Solar Controller 1 x English User Manual 1 x Temp Sensor Detail Pictures:

12V 10A Single Output Switching Power Supply Description: 12V 10A Single Output Switching Power Supply The Single Switching Power Supply has wide input voltage range, steady and precise output voltage. Full load burn-in test. Over current, over voltage, short circuit protection. Low output ripple and noise.       Specification Input voltage: AC 110V-220V Input frequency: Hz Output voltage: 12V   Output current: 10A  

Description:   CPS-3010 0-30V 0-10A 110V/220V Compact Digital Adjustable DC Power Supply   Features:   Top performance cost ratio High power density, smallest and compact Aluminum shell, lower EMI. Using Encoder to set the voltage and current. Four digital volt meter and three digital current meter. Switchable 110V and 220V inputs. Frequency range 45 - 65Hz Output range 0 -30V Output Current range 0 - 10A Intelligent protection: Tracking OVP, Tracking OCP, OTP, Output short circuit protection No Load Current (220V) Volt meter Accuracy 0.3% + 1 digits Current Meter Accuracy 0.3% + 2 digits LOCK switch   Specification:   Operation Voltage Range: 198 – 264V AC Operation Frequency Range: 45 – 65HZ Output Voltage Range: 0 – 30V Output Current Range: 0 – 10A Efficiency (220Vac/full load): ≥88% Full Load Input Current(220V AC): ≤2.3A No Load Input Current(220V AC): ≤120mA Volt Meter Accuracy: ≤ 0.3% + 1 digits Current Meter Accuracy: ≤ 0.3% + 3 digit Constant Voltage: Load Regulation (0-100%): ≤ 30mV Line Regulation(198-264V AC): ≤ 10mV Ripple & Noise (Peak-Peak): ≤ 40mV Ripple & Noise (r.m.s): ≤ 5mV Set Accuracy: ≤ 0.3% + 10mV Transient Response Time (50%-100% rated Load): ≤ 1.0ms Constant Current: Load Regulation(90%-10% Rated Voltage): ≤ 100mA Line Regulation (198-264V AC): ≤ 50mA Ripple & Noise (Peak-Peak): ≤ 100mAp-p Set Accuracy: ≤ 0.3% + 20mA Size(width× height× depth): 120×55×240mm Net Weight: 1.2kg Package includes:   1 x CPS-3010 DC Power Supply 1 x AC Power cable 1 x User Manual   Details pictures:  ,  ,,,      

DC-DC Adjustable Voltage Step up & Step Down / Current Driver/ Charger: Description: 1piece of DC-DC adjustable step up/ step-down (Voltage & Current) power supply module Input Voltage: 5-35V Output Voltage: Continuously adjustable from 1.25 V to 30V Rated Output Current: 3A Max. Output Current: 4A (more than 15W, preferably with a heat sink) Size (L x W x H): Approx. 1.9 x 0.95 x 0.5 inch / 4.8 x 2.4 x 1.3cm Indicator Light Constant current indicator(red) Charging indicator(red) Charged full (green) Applications: High-power LED constant current drive Lithium battery charger (including ferroelectric) 4V, 6V, 12V, 14V, 24V battery charger Nickel cadmium, nickel metal hydride battery pack charger Solar panels and wind turbines Battery Use: Make sure of the voltage and current of the battery you need to charge Adjust the constant voltage potentiometer to make the output voltage same to the charge voltage Potentiometer Adjustment Direction: Clockwise (increase), counterclockwise (decrease) Use the multimeter in 10A current scale to measure output short-circuit current, and adjust the current potentiometer to make sure the output current to the expected charging current value The charge current of transfer lamp is default 0.1 times of the charging current (constant current value) Connected to the battery and try to charging (for previous 5 steps, module input terminal is connected to power source, output load is NOT connected to batteries) LED Constant Current Driver Use: Make sure operating current and Max operating Voltage of the LED you need to drive Adjust the constant voltage potentiometer to make sure the output Voltage is up to LED Max operating Voltage Use the multimeter in 10A current scale to measure output short-circuit current, and adjust the current potentiometer to make sure the output current to the expected LED operating current Join LED, test (For the above 3 steps, module input terminal is connected to power source, output load is NOT connected to LED)

Description: 15A PMW Solar Panel Battery Regulator Charge Electrical Controller Function: Always keep the battery on fill voltage condition. Prevent the battery from over-charging. Prevent the battery from over-discharging. Prevent the battery from reverse charging to solar panels during nights. Reverse Polarity Protection for Battery Reverse Polarity Protection for Solar Panels When the battery voltage is low, the controller will automatically cut off the load from the system. If the voltage of battery is back to normal and the load will restart working. Thunder protection: According to the battery voltage grade, the controller can automatically set charge-off voltage, the load-off voltage, the load- restore voltage. (The parameter is default under 25¿ condition, locked by the CPU procedure, cannot adjust.) The controller will automatically compensate the temperature of the charging voltage according to the changes of ambient temperature. Warning: Before connecting to the solar panel, please connect the controller to the battery; do not use solar panel supply power to the loads directly. Notes: Do not use lamplight to charge the solar panel (lamplight is too weak to charge) DC power source to replace the solar panel will cause troubles to controller. Choose the suitable wire which diameter should not be too small, please refer to the parameter. Indicate Light and Button: When Red LED (CHARGE) is on, battery is charged up strongly; When Red LED is flickering, battery is charged up in constant voltage; when Red LED is oft charge off When Green LED (LOAD) is on, loads are working; when Green LED (LOAD) is off, loads stop working. Three Colorchanging LED (BATTERY), When light is red, it indicates low voltage, green indicate battery full charged, orange indicate normal status. Color-changing LED working voltage indicates area: Color-changing LED 12V 24V Red LED 10.5V-11V 21V-22V Orange LED 10.511V-13.7V 21 - 22V-27.4V Green LED ¿13.7V ¿ 27.4V Parameters: Rated Vo1tae 12V / 24V Max Load current 5A 10A 15A 20A 30A 4OA 60A Input voltage range 12V - 20V/24 Length¿1m Charge loop drop Length¿1m Discharge loop drop Full charge cut 1.37V - 14.4V/27.4V -

General Information: Digital Control Buck-Boost Supply Power Module put the collection of analog integration and digital control functions in one. Its adjustable output voltage range is 0-50.00V, step by 0.01V. Its adjustable output current range is 0-5.000A, step by 0.001A. This module has power-down stored function and can store 10 groups preset value. And it also has the function of extracting quickly two groups stored value. Compared with the traditional analog power supply, it is more convenient to quickly extract the voltage or current required. LCD display on the module has the function of digital voltmeter and ammeter. You can view the preset voltage, input voltage, output voltage, the preset current, output current, output power, etc. On the output state remind area, you can see that output opens or not, the state of constant voltage and constant current, output is normal or not, the key is locked or not, and the current data groups that is being used. On the setting data interface, you can adjust overvoltage value, overcurrent value, over-power value, data group and LCD brightness. This module adopts buck-boost structure; when input voltage is lower than, equal to or higher than output voltage, output voltage is still stable and changeless. This feature has wide range of application. Notice: 1.Before buying this product, please download the upper computer software and test, if it fits your computer, you can buy 2. the upper computer only support For Win7 and above PC software & manual: Download here! CE: http://files.banggood.com/2018/10/DPH5005-CE.jpg Technical parameters: Input voltage range: 6-50V Output voltage range: 0V-50.00V Output current: 0-5.000A Output power range: 0-250W Max allowable input current: 10A Output ripple: about 100mVpp Product Weight: about 267g Display module size: 79*43*38(mm) (L*W*H) Open size: 76mm*39mm Power module size: 93*72*42(mm) (L*W*H) Length of connecting line: 200mm Fixed hole center distance: 86mm, 64mm Package included: Type A: DPH5005 No Communication Version Type B: DPH5005 USB Communication Version Type C: DPH5005 Communication Version USB Board+Bluetooth Board Output voltage program and read back resolution: 0.01V Output current program and read back resolution: 0.001A Output Voltage program and read back accuracy: ± (0.5% + 2 digits) Output Current program and read back accuracy: ± (0.5% + 3 digits) Temperature of the application environment: -10°c ~45°c NOTE: 1.If you want to ensure output at full load, you must make sure that input is higher than 28V and 280W; pay attention to heat elimination at full load. 2. Connection between display part and power part should be according to the corresponding words. Otherwise it will not work by wrong connection Connection description: IN+: Input positive IN-: Input negative: OUT+: Output positive: OUT-: Output negative Note: Input voltage range is DC 6-50V and 50V is the limit voltage; please leave a room to use. Or else it will be burnt. The input must be DC power supply, not AC 220V, or else it will be burnt too. Though this module has reverse connection protection and output short circuit protection, you can muse be in strict accordance with connection description to connect. If you connect the supply power with output, the module will be burnt. Panel description: 1-Voltage setting/Page up to choose/Shortcut extract M1 data group 2-Data setting/ Extract value of the specified data group/Store value into the specified data group 3-Current setting/Page Down to choose/Shortcut extract M2 data group 4-1.44 inch color LCD screen 5-Coding potentiometer/Data adjustment/Lock all buttons 6-Open or close output Display interface description: 7-The preset value of output voltage 8- The actual value of output voltage 9-The actual value of output current 10-The actual value of output power 11-The actual value of input voltage 12-The preset value of output current 13-Key lock or unlock prompt 14-Output normal or not prompt 15-Constant voltage and constant current status prompt 16-Data set prompt 17-Open or close output prompt 18-Preset output voltage 19-Preset output current 20-Preset over- voltage 21-Preset over-current 22-Preset over-power 23-Preset screen brightness 24-Preset data set 25-The actual value of output voltage and output current Operating instructions: When connect the power supply, the screen shows welcome window firstly and then comes into main interface. On the main interface, the output set voltage value and the

BEST QUALITY PRODUCTS AND BEST PRICES!!! DON'T MISS OUT!!!DON'T BE LATE!!! -PLEASE NOTE THAT OUR PRICES ARE INCLUSIVE OF VAT ADDED (TAX 10AMP POWER SUPPLY 12 VDC, 10A Metal Electrical Box Screw-Type Connectors LED Fault Light We also stock solar panels, charge controllers,Inverters, batteries LED down-lights and many more..... Please inquire about our prices, we will send you the full catalog. PLEASE CONTACT US,OUR PROFESSIONAL TECHNICAL TEAM ARE WAITING FOR YOUR QUERIES AND SOLVE YOUR ELECTRICITY DEMANDS. WE VALUE OUR CLIENT WITH INTEGRITY AND WE PROMISE TO TREAT YOU WITH A SMILE,HONESTLY AND RESPECT. PLEASE BE ADVISED THAT WE DO INSTALLATION AS WELL PHONE US,CONTACTS US OR VISIT OUR SHOWROOM TEL:/ DIRECT LINE:(012) TRADING HOURS MON-FRIDAY: to SATURDAY: to Sunday:closed Public Holiday:closed VISIT US TO OUR SHOWROOM IN CENTURION AND SEE WHAT WE MEAN WITH GOOD PRODUCTS & GOOD PRICES PRICES ARE SUBJECTS TO CHANGE WITHOUT PRIOR NOTICE DUE RAND/DOLLAR FLUCTUATION.

Description:   BSDE BLS028A 2CH Smart Wireless Remote Control Switch for LED Light TV Computer Microwave Cooker     Remote control switch is used mainly to control lighting. after installing remote control switches, the receiver can be used in long distance free to manipulate and control the power on and off, without alignment control. It's really user-friendly because of a full  360-degree control. Also because it  can control appliances  through wall  , never affected by direction or distance.   Scope of Application: Can be used for lots of household appliances, such as,  incandescent lamps, energy saving lamps, fluorescent lamp, (electronic), ring-shaped light pipe, light pipe, combination lamps, decorative lanterns, LED light bar, LED light, fan, TV, computer, and so on. Suitable for  home, office, store, bar, hospital, hotel, warehouse, meeting room  etc.   Specification: Item Type:  2 Channel  Remote Control Switch Color: Greyish white Remote Control Dimensions: 105MM x 45MM x 18MM (L x W x H) Receiver Size: 62MM x 45MM x 24MM (Lx W x H) Voltage:  220V-240V AC Voltage Frequency: 50/60 Hz Receiving Frequency: 315MHz Each Load:     Incandescent:  1000W          Energy-saving Lamps:  250W  Load Current Standard: Adopting Standard 10A Relay Control Control Eistance:  5-15m in the house,  20m outdoor Remote Controller material: Fireproof ABS Ambient Temperature: Operation Instructions:   Pressbutton A,  turn on blue wire, press again turn off   Pressbutton B,  turn on white wire, press again turn off   Press ON/ OFF, turn on/off  blue wire,white wire   Packing included:    1 x BSDE BLS028A 2CH Remote Control Switch (Battery is not included) 1 x RF Receiver  1 x Remote Control Fixed Frame   Details pictures:    

Description:   BSDE BLS048B 4CH Smart Digital Wireless Remote Control Switch RF Receiver for Home  Appliance    Remote control switch is used mainly to control lighting. after installing remote control switches, the receiver can be used in long distance free to manipulate and control the power on and off, without alignment control. It's really user-friendly because of a full  360-degree control. Also because it  can control appliances  through wall  , never affected by direction or distance.   Scope of Application: Can be used for lots of household appliances, such as,  incandescent lamps, energy saving lamps, fluorescent lamp, (electronic), ring-shaped light pipe, light pipe, combination lamps, decorative lanterns, LED light bar, LED light, fan, TV, computer, and so on. Suitable for  home, office, store, bar, hospital, hotel, warehouse, meeting room  etc.   Specification: Item Type:  4 Channel  Remote Control Switch Color: Greyish white Remote Control Dimensions: 105MM x 45MM x 18MM (L x W x H) Receiver Size: 82MM x 53MM x 24MM (Lx W x H) Voltage:  220V-240V AC Voltage Frequency: 50/60 Hz Receiving Frequency: 315MHz Each Load:     Incandescent:  1000W          Energy-saving Lamps:  250W  Load Current Standard: Adopting Standard 10A Relay Control Control Eistance:  5-15m in the house,  20m outdoor Remote Controller material: Fireproof ABS Ambient Temperature: Operation Instructions:   Pressbutton 1,  turn on blue wire, press again turn off   Pressbutton 2,  turn on white wire, press again turn off   Pressbutton 3,  turn on yellow wire, press again turn off   Press button 4,  turn on brown wire, press again turn off   Press ON/ OFF, turn on/off  blue wire,white wire,yellow wire,brown wire,  press again turn off   Packing included:    1 x BSDE BLS048B 4CH Remote Control Switch  (Battery is not included) 1 x RF Receiver  1 x Remote Control Fixed Frame Details pictures:    

Description:   BSDE BLS028B 2CH Smart Digital Wireless Remote Control Switch RF Receiver for Home  Appliance    Remote control switch is used mainly to control lighting. after installing remote control switches, the receiver can be used in long distance free to manipulate and control the power on and off, without alignment control. It's really user-friendly because of a full  360-degree control. Also because it  can control appliances  through wall  , never affected by direction or distance.   Scope of Application: Can be used for lots of household appliances, such as,  incandescent lamps, energy saving lamps, fluorescent lamp, (electronic), ring-shaped light pipe, light pipe, combination lamps, decorative lanterns, LED light bar, LED light, fan, TV, computer, and so on. Suitable for  home, office, store, bar, hospital, hotel, warehouse, meeting room  etc.   Specification: Item Type:  2 Channel  Remote Control Switch Color: Greyish white Remote Control Dimensions: 105MM x 45MM x 18MM (L x W x H) Receiver Size: 62MM x 45MM x 24MM (Lx W x H) Voltage:  220V-240V AC Voltage Frequency: 50/60 Hz Receiving Frequency: 315MHz Each Load:     Incandescent:  1000W          Energy-saving Lamps:  250W  Load Current Standard: Adopting Standard 10A Relay Control Control Eistance:  5-15m in the house,  20m outdoor Remote Controller material: Fireproof ABS Ambient Temperature: Operation Instructions:   Pressbutton 1,  turn on blue wire, press again turn off   Pressbutton 2,  turn on white wire, press again turn off   Press ON/ OFF, turn on/off  blue wire,white wire   Packing included:    1 x BSDE BLS028B 2CH Remote Control Switch  (Battery is not included) 1 x RF Receiver  1 x Remote Control Fixed Frame   Details pictures:    

Description: BSDE BLS018A 1CH Smart Wireless Remote Control Switch for LED Light TV Computer Microwave Cooker Remote control switch is used mainly to control lighting. after installing remote control switches, the receiver can be used in long distance free to manipulate and control the power on and off, without alignment control. It's really user-friendly because of a full 360-degree control. Also because it can control appliances through wall, never affected by direction or distance. Scope of Application: Can be used for lots of household appliances, such as, incandescent lamps, energy saving lamps, fluorescent lamp, (electronic), ring-shaped light pipe, light pipe, combination lamps, decorative lanterns, LED light bar, LED light, fan, TV, computer, and so on. Suitable for home, office, store, bar, hospital, hotel, warehouse, meeting room etc. Specification: Item Type: 1 Channel Remote Control Switch Color: Greyish white Remote Control Dimensions: 95MM x 38MM x 16MM (L x W x H) Receiver Size: 62MM x 45MM x 24MM (Lx W x H) Voltage: 220V-240V AC Voltage Frequency: 50/60 Hz Receiving Frequency: 315MHz Each Load: Incandescent: 1000W Energy-saving Lamps: 250W Load Current Standard: Adopting Standard 10A Relay Control Control Eistance: 5-15m in the house, 20m outdoor Remote Controller material: Fireproof ABS Ambient Temperature: Operation Instructions: Press ON/ OFF, turn on/off blue wire. Packing included: 1 x BSDE BLS018A 1CH Remote Control Switch 1 x RF Receiver 1 x Remote Control Fixed Frame Details pictures:

    Go CNC Routers  Features:  Cutting area:  1000mmx1000mm.  Cutting depth 80mm.  Open ends allow pass through of longer materials.  All aluminium frame.  5 cutting bits  (1mm, 1.5mm, 2mm, 2.5mm, 3mm) Collets 3mm, 6mm, 8mm Electronics control box with USB cable connection (cable included)  Full cable management with X & Y axis cable drag chains.  Makita RT0700C Router (12 month warranty from any Makita dealer) 6 months warranty  Manual Speed Controlled between 12 000 RPM - 30 000 RPM.   Requirements:  Personal computer or Laptop running Windows 7, 8 or 10.  USB port on computer  Easel Inventables and USB CNC setup    Specifications:  4x Nema23 stepper motors 12.6kg/cm 175oz/in.  4 Axis USBCNC Stepper Motor Driver Controller Board.  24V 10A 250W Power Supply.  GT3 reinforced neoprene 3mm pitch timing belts on X & Y axis.   Dual motors on Y axis.  T8 lead screw on Z axis  Configured resolution: 0.0375mm  65mm Router Spindle Mount (suitable for Makita RT0700C).         Please Confirm Stock Before Order Please Use Q&A Please allow 7-10 working days for the item to be ready, As this item is order on request And please allow 5-7 working days for delivery.            

Description: BSDE BLS038A 3CH Smart Digital Wireless Remote Control Switch RF Receiver for Home Appliance Remote control switch is used mainly to control lighting. after installing remote control switches, the receiver can be used in long distance free to manipulate and control the power on and off, without alignment control. It's really user-friendly because of a full 360-degree control. Also because it can control appliances through wall, never affected by direction or distance. Scope of Application: Can be used for lots of household appliances, such as, incandescent lamps, energy saving lamps, fluorescent lamp, (electronic), ring-shaped light pipe, light pipe, combination lamps, decorative lanterns, LED light bar, LED light, fan, TV, computer, and so on. Suitable for home, office, store, bar, hospital, hotel, warehouse, meeting room etc. Specification: Item Type: 3 Channel Remote Control Switch Color: Greyish white Remote Control Dimensions: 105MM x 45MM x 18MM (L x W x H) Receiver Size: 62MM x 45MM x 24MM (Lx W x H) Voltage: 220V-240V AC Voltage Frequency: 50/60 Hz Receiving Frequency: 315MHz Each Load: Incandescent: 1000W Energy-saving Lamps: 250W Load Current Standard: Adopting Standard 10A Relay Control Control Eistance: 5-15m in the house, 20m outdoor Remote Controller material: Fireproof ABS Ambient Temperature: Operation Instructions: Pressbutton A, turn on blue wire, press again turn off Pressbutton B, turn on white wire, press again turn off Pressbutton C, turn on yellow wire, press again turn off Press ON/ OFF, turn on/off blue wire,white wire, yellow wire, press again turn off Packing included: 1 x BSDE BLS038A 3CH Remote Control Switch (Battery is not included) 1 x RF Receiver 1 x Remote Control Fixed Frame Details pictures:

- Quantity: 1 - Color: Red - Material: Glass fiber FR4 - Type: Non-isolated boost module - Input voltage: 10~32V - Output voltage: 35V - Output current: 5A (Max) - Input current: 16A (Max), please cool it when it's over 10A - Output power: Natural cool down 80W (Max) - Heat dissipation power: 120W - Switch efficiency: Standard 90% - Output ripple: 2% (Max) - Bandwidth: 20MHz - 20M bandwidth input 4V, output 5.1V / 1A - Working temperature: -40'C~85'C (Industrial) - Full load temperature: 45'C - No-load current: 25mA - Loading adjustment rate: +/- 0.5% - Voltage adjustment rate: +/- 0.5% - Dynamic response speed: 5% 200us - Wiring way: None-soldering, with terminal - Great for DIY project General Quantity: Material: Specification English Manual / Spec No Dimensions & Weight Packing List 1 * piece

3pcs 0.56 Inch Blue Red Dual LED Display Mini Digital Voltmeter Ammeter DC 100V Package weight: 0.23 kg Description: Operating voltage:DC 4 ~ 30V Measure voltage: DC 0 ~ 100V Minimum resolution(V): 0.1V Measure current:50A (require external shunt) Minimum resolution(A): 0.1A Operating current: Display: three 0.28" LED digital tube Display color: Red and Blue (two-color display) Refresh rate: about 300mS / times Measure accuracy: 1% (± 1 digit) Operating temperature: -10 to 65° c Operating Humidity: 10 to 80% (non-condensing) Working pressure: 80 to 106 kPa Applications:Suitable for automotive/electric cars/motorcycles battery monitoring or other products voltage current measurement Wiring: Black line (thin): vacant or buck circuit (module) negative Red line (thin): power supply+ Black line (thick): COM, common measuring Red line (thick): PW+, measuring terminal voltage input positive Yellow line (thick): IN+, current input+ (Please refer to the wiring diagrams for more details) Notice: The voltage between the thin red and thin black lines must be within DC 4-30V The ammeter can only be connected to the negative of the device under test Exceeds 5A, long-term full load working continuously, it is recommended that the measurement side of the leads are directly soldered to the socket When the black thin line vacant, it is better to use insulating tape around the exposed part of the wire, to prevent short circuits If just be used as a voltmeter, it is recommended that the yellow line and the black line were connected together, to prevent the ammeter digital flashing It is unsuitable to use this meter to test current less than 10A. ￢ﾀﾋPackage included: 3 x Digital Voltmeter Ammeter Meter 3 x Current Shunt 3 x Cable Click here for more deals 3pcs 0.56 Inch Blue Red Dual LED Display Mini Digital Voltmeter Ammeter DC 100V 3pcs 0.56 Inch Blue Red Dual LED Display Mini Digital Voltmeter Ammeter DC 100V

5pcs 0.56 Inch Blue Red Dual LED Display Mini Digital Voltmeter Ammeter DC 100V Package weight: 0.38 kg Description: Operating voltage:DC 4 ~ 30V Measure voltage: DC 0 ~ 100V Minimum resolution(V): 0.1V Measure current:50A (require external shunt) Minimum resolution(A): 0.1A Operating current: Display: three 0.28" LED digital tube Display color: Red and Blue (two-color display) Refresh rate: about 300mS / times Measure accuracy: 1% (± 1 digit) Operating temperature: -10 to 65° c Operating Humidity: 10 to 80% (non-condensing) Working pressure: 80 to 106 kPa Applications:Suitable for automotive/electric cars/motorcycles battery monitoring or other products voltage current measurement Wiring: Black line (thin): vacant or buck circuit (module) negative Red line (thin): power supply+ Black line (thick): COM, common measuring Red line (thick): PW+, measuring terminal voltage input positive Yellow line (thick): IN+, current input+ (Please refer to the wiring diagrams for more details) Notice: The voltage between the thin red and thin black lines must be within DC 4-30V The ammeter can only be connected to the negative of the device under test Exceeds 5A, long-term full load working continuously, it is recommended that the measurement side of the leads are directly soldered to the socket When the black thin line vacant, it is better to use insulating tape around the exposed part of the wire, to prevent short circuits If just be used as a voltmeter, it is recommended that the yellow line and the black line were connected together, to prevent the ammeter digital flashing It is unsuitable to use this meter to test current less than 10A. ￢ﾀﾋPackage included: 5 x Digital Voltmeter Ammeter Meter 5 x Current Shunt 5 x Cable Click here for more deals 5pcs 0.56 Inch Blue Red Dual LED Display Mini Digital Voltmeter Ammeter DC 100V 5pcs 0.56 Inch Blue Red Dual LED Display Mini Digital Voltmeter Ammeter DC 100V