30hp yamaha engine

30hp yamaha Long shaft Controls and cables Original condition R11 950 Contact 0835255155

30hp yamaha Controls and cables R11500 Contact 0835255155

30hp 3 cilinder jamaha pull start Start and go Gearbox seals must get replaced in time Contack 0815196804

SUPERCAT (WITBLITZ) + 30HP YAMAHA 2-STROKE - R55 000 2004 30hp Yamaha 2-stroke, 2 cylinder Stainless steel anchor chute Wet deck with closable scuppers Centre sit down console Seat in front of console with storage Vertical rod storage 6x rod holders Navigation & anchor lights Single axle galvanized trailer. Contact Kerry - 084 896 2948 / Kerwyn - 082 903 3558 or visit www.bayviewboating.co.za

410 Cathedral hull boat. Galvanised trailer with roadworthy. 30HP Yamaha motor. Custom made tarpaulin cover. All in excellent condition. Flat self-draining wet deck. High level LED trailer lights makes launching this light boat a breeze (no old fashioned light board to remove). Viewing by appointment in Kenton on Sea

!!!4m Wildcat semi-rigid rubberduck for sale!!! Yamaha 30hp 3cyl,Tiller arm engine. 100% Galvanised trailer, new bearings & Tyres, Rims Powdercoated. Roadworthy and licenced Safety equipment in capsize bottel with s/stl holder, lifejackets, anchor, oars, pump, fire extinguisher. Hulk 22l fuel tank & Fuel line. S/stl trawilng bar with HDPE board and S/stl rodholders. Delivery can be arranged in Struisbaai, Hermanus, Witsand. Francois 0845123563 Search words: Infanta, Wildcat, Falcon, Ceaser, Gemini, Thundercat, Fishing, Boat, Racing.

This boat is as new and the motor has done hardly any hours. All paperwork is up to date, just get on and go. New wheel bearings. Call 0722647195

Yamaha 30hp tiller arm or steering Good condition Head recently resprayed and new decals fitted Upgraded my motor Runs like a dream Comes with petrol tank R18000 onco Not desperate to sell so no silly offers please

30hp 2 cylinder yamaha prop Good condition R500 Contact 0835255155

I have a 3 cylinder, 30hp, longshaft for sale, with tiller arm. In good condition.

Yamha mariner starter complete with ring gear and starter plus bracket with all bolts fits 25hp 30hp 40hp yamaha and mariner can be tested before purchase r2500

MULTIFLEX engine control cables are made from non-corrosive materials. Lubricated stainless steel inner cable for maximum efficiency, stainless steel or brass end fittings with reinforced outer poly jacket. Suits sterndrives, inboards and outboards. HOW TO MEASURE CONTROL CABLES For a new installation measure cable routing path from control head attachment point to engine connection, as follows: Outboards: Measure from control along unobstructed cable routing to center of outboard. Add four feet to allow for loop which provides unrestricted engine movement. Round up to next whole foot and order required cable part number. (Last two digits of cable part number equal cable length in feet.) Inboards & Stern Drives: Measure from control along unobstructed cable routing to shift and/or throttle connection. Round this dimension off to the next whole foot and order required cable part number. (Last two digits of cable part number equal cable length in feet.) FOR REPLACEMENT OF EXISTING CABLE If you removed the old cable, measure for replacement cable as follows: Measure from tip to tip and round up to next whole foot, if necessary (aftermarket cables are sold in foot increments). SKU: 15480 Please contact (or whatsapp) me on 062 857 9004 or email to bsapotchefstroom@gmail.com for more details regarding this product.

MULTIFLEX engine control cables are made from non-corrosive materials. Lubricated stainless steel inner cable for maximum efficiency, stainless steel or brass end fittings with reinforced outer poly jacket. Suits sterndrives, inboards and outboards. HOW TO MEASURE CONTROL CABLES For a new installation measure cable routing path from control head attachment point to engine connection, as follows: Outboards: Measure from control along unobstructed cable routing to center of outboard. Add four feet to allow for loop which provides unrestricted engine movement. Round up to next whole foot and order required cable part number. (Last two digits of cable part number equal cable length in feet.) Inboards & Stern Drives: Measure from control along unobstructed cable routing to shift and/or throttle connection. Round this dimension off to the next whole foot and order required cable part number. (Last two digits of cable part number equal cable length in feet.) FOR REPLACEMENT OF EXISTING CABLE If you removed the old cable, measure for replacement cable as follows: Measure from tip to tip and round up to next whole foot, if necessary (aftermarket cables are sold in foot increments) SKU: 15480 Contact Us on 061 935 3537 or email: bsajohannesburg@gmail.com

MULTIFLEX engine control cables are made from non-corrosive materials. Lubricated stainless steel inner cable for maximum efficiency, stainless steel or brass end fittings with reinforced outer poly jacket. Suits sterndrives, inboards and outboards. HOW TO MEASURE CONTROL CABLES For a new installation measure cable routing path from control head attachment point to engine connection, as follows - Outboards: Measure from control along unobstructed cable routing to center of outboard. Add four feet to allow for loop which provides unrestricted engine movement. Round up to next whole foot and order required cable part number. Inboards & Stern Drives: Measure from control along unobstructed cable routing to shift and/or throttle connection. Round this dimension off to the next whole foot and order required cable part number. FOR REPLACEMENT OF EXISTING CABLE If you removed the old cable, measure for replacement cable as follows: Measure from tip to tip and round up to next whole foot, if necessary (aftermarket cables are sold in foot increments). SKU: 15486 For more information on this Product: Contact Etienne on 073 409 4629 (Or Whats App)

MULTIFLEX engine control cables are made from non-corrosive materials. Lubricated stainless steel inner cable for maximum efficiency, stainless steel or brass end fittings with reinforced outer poly jacket. Suits sterndrives, inboards and outboards. HOW TO MEASURE CONTROL CABLES For a new installation measure cable routing path from control head attachment point to engine connection, as follows - Outboards: Measure from control along unobstructed cable routing to center of outboard. Add four feet to allow for loop which provides unrestricted engine movement. Round up to next whole foot and order required cable part number. Inboards & Stern Drives: Measure from control along unobstructed cable routing to shift and/or throttle connection. Round this dimension off to the next whole foot and order required cable part number. FOR REPLACEMENT OF EXISTING CABLE If you removed the old cable, measure for replacement cable as follows: Measure from tip to tip and round up to next whole foot, if necessary (aftermarket cables are sold in foot increments). SKU: 15489 Contact Us on 061 935 3537 or email: bsajohannesburg@gmail.com