Photosensitive resistance

Buy Photosensitive Resistance Sensor With Relay Module 5V Optical Control Switch Light Detection Switch for R227.00

Buy 3pcs 4pin Optical Sensitive Resistance Light Detection Photosensitive Sensor Module for R161.54

Buy 50pcs 4pin Optical Sensitive Resistance Light Detection Photosensitive Sensor Module Geekcreit for A for R406.00

Specifications: Track width: 15mm Color: As shown Size(Length x Width): appr. 10 x 7cm Power: 2 x AA battery Voltage: 3V The assembly steps: Step 1: Welding circuit Electric welding part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance, is important to use multimeter to confirm resistance is correct, D4, D5 R13 R14 can temporarily not welding, integrated circuit chips can temporarily not inserted Step 2: Mechanical assembly The red line is connected to the 3V positive power supply, the yellow line grounding, excess wire can be used for motor wire. Step 3: The installation of a photoelectric circuit Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test. Step 4: Vehicle debugging The right direction is along the universal wheel direction, if you press and hold the left photoresistor, the wheels on the right side of the car should be rotated. Press and hold the right photoresistor, the wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring of back side. Click to watch installing and debugging video Note: Battery is not included. Package included: 1 x Tracking Robot Car Kit

Specifications: 1.Photoresistor (LDR) based line following 2.Individual wheel control 3.Chipset: LM393 4.Material: Electrical components 5.Color: See picture 6.Board Size:10.4*7.2cm The assembly steps: Step 1: Welding circuit - Electric welding part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance is important to use the multi meter to confirm resistance is correct Step 2: Mechanical assembly - The red line is connected to the 3V positive power supply, the yellow line grounding, the excess wire can be used for the motor wire. Step 3: The installation of a photoelectric circuit - Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test. Step 4: Vehicle debugging - The right direction is along the universal wheel direction if you press and hold the left photoresistor - The wheels on the right side of the car should be rotated. Press and hold the right photoresistor - The wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring on the back side. Note: The battery is not included. Package Included: 1 x Base board 1 x 35mm Wheels 1 x Rubber Wheel bands 1 x AA Battery holder 1 x Screw set 1 x LM393 Chipset 1 x 8pin DIP Socket 10 x Resistor 2 x Gearded DC Motors 2 x Electrolytic capacitor 2 x Light dependant resistors 2 x Transitors 2 x White LED 2 x Red LED 1 x Power switch 4 x 70mm Leads

The Assembly Steps: Step 1: Welding circuit Electric welding part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance, is important to use multimeter to confirm resistance is correct, D4, D5 R13 R14 can temporarily not welding, integrated circuit chips can temporarily not inserted Step 2: Mechanical assembly The red line is connected to the 3V positive power supply, the yellow line grounding, excess wire can be used for motor wire. Step 3: The installation of a photoelectric circuit Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test. Step 4: Vehicle debugging The right direction is along the universal wheel direction, if you press and hold the left photoresistor, the wheels on the right side of the car should be rotated. Press and hold the right photoresistor, the wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring of back side. Package Include: 1 X Module Smart Tracking Robot Car Electronic DIY Kit With Reduction Motor Set 1 X User Manual

Tracking Robot Car Electronic DIY Kit With Reduction Motor The assembly steps: Step 1: Welding circuit Electric welding part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance, is important to use multimeter to confirm resistance is correct, D4, D5 R13 R14 can temporarily not welding, integrated circuit chips can temporarily not inserted Step 2: Mechanical assembly The red line is connected to the 3V positive power supply, the yellow line grounding, excess wire can be used for motor wire. Step 3: The installation of a photoelectric circuit Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test. Step 4: Vehicle debugging The right direction is along the universal wheel direction, if you press and hold the left photoresistor, the wheels on the right side of the car should be rotated. Press and hold the right photoresistor, the wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring of back side. Note: We don't supply any manuals please note about this befor you buy it. Package included: 5 x Electronic DIY Kit (batteries are not included)

Tracking Robot Car Electronic DIY Kit With Reduction Motor The assembly steps: Step 1: Welding circuit Electric welding part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance, is important to use multimeter to confirm resistance is correct, D4, D5 R13 R14 can temporarily not welding, integrated circuit chips can temporarily not inserted Step 2: Mechanical assembly The red line is connected to the 3V positive power supply, the yellow line grounding, excess wire can be used for motor wire. Step 3: The installation of a photoelectric circuit Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test. Step 4: Vehicle debugging The right direction is along the universal wheel direction, if you press and hold the left photoresistor, the wheels on the right side of the car should be rotated. Press and hold the right photoresistor, the wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring of back side. Note: We don't supply any manuals please note about this befor you buy it. Package included: 3 x Electronic DIY Kit (batteries are not included)

Electronic Component Parts Pack Starter Beginner Kit For UNO Arduino Feature: This kit is a new development kit, it contains multi-colors LED, resistors, capacitors, and other commonly used digital electronic components and small breadboard, do not include the control board. It is very suitable for electronics beginners. All information in this kit are to UNO as a control board, if you use other types of Arduino boards, you can find relevant information on the Internet, can also refer to the information we provided to make certain changes. Package included: 1 x Small component box 1 x 830 hole breadboard 1 x Plug-led three-color components 1 x Active buzzer component 1 x Passive components buzzer 1 x Fire component 1 x One digital tube 1 x Four digital tube 1 x LM35 component 1 x 74HC595 chip 1 x 9g Steering engine 1 x 10K Adjustable potentiometer (3386 MU 103 3 pin) 1 x 40 pin header 1 x Resistance card 1 x ARC plate (12 x 8 cm) 1 x 8*8 Dot matrix module 1 x Kit box (18.4 x 8.8 x 4.5 cm) 2 x Ball switching component 2 x 103 thermistor 2 x Photosensitive resistance component 2 x 4007 diode 4 x Buttons 5 x 100UF electrolytic capacitor 10 x Yellow LED 10 x Red LED 10 x Blue LED 10 x Green LED 10 x 220R resistor 10 x 1K resistor 10 x 10K resistor 10 x 10NF ceramic capacitor 10 x 100NF ceramic capacitor 50 x Breadboard jumper wire

Geekcreit™ UNO R3 ATmega328P Development Board For Arduino Output voltage: DC 5V / 3.3V ATmega328P No USB cable version This version can not compatible with MAC OS system   Features: Open the original schematic design, free development software interface download, also allow your needs to be modified, easy and convenient to download the program. Can simply use sensors, all kinds of electronic components connection (such as LED lights, buzzer, buttons and photosensitive resistance, etc.), make all sorts of interesting work. Using high-speed microprocessor controller (ATMEGA328), development interface and environment are all very simple, easy to understand, very suitable for beginners to learn. Description: Digital I / O: 0 - 13 Analog I / O: 0 - 5 Support ISP download function Input voltage: DC 5V ~ 9V (No external power supply when connected to the computer) Output voltage: DC 5V / 3.3V Using Atmel Atmega328 microprocessor controller How to use: 1. Download the IDE arduino    Link: http: http://arduino.cc/en/Main/Software (Copy to open) 2. Download the USB chip driver    Link: (Copy to open) 3. Plug in UNO development board, the driver will be installed automatically 4. Select the UNO from the die 5. Select the COM port 6. The best choice first, arduino come with routine procedures, burn into it. Package included: 1 x UNO R3 Development Board

Specification: Sensor RGB 720P 1/4 inch CMOS Lens 4mm standard lens, a fixed optional diaphragm Resolution VGA(640*480), 720P(1280*720) optical Mini Sensitivity 0.5Lux Infrared night vision Maximum support 15 meters, through the automatic photosensitive resistance control infrared open Compression H.264 dual stream Frame 1-30fps Video code stream 16Kbps-4Mbps Audio format G.711A System interface RJ45 Ethernet interface Support protocol TCP/IP, UDP/IP, HTTP, SMTP, FTP, DHCP, UPNP, NTP WiFi protocol IEEE 802.11b/g/n Image rotation Mirror / inversion Video control   Support Motion detection Support Alarm action   Email alarm sent/real-time alarm information push TF storage Max support 128G TF card Power supply DC 12V 1A Power waste Working temperature -10℃ to  55℃ Working humidity  10%-80% no condensation Package includeds: 1 x Outdoor IP Camera 3 x Antenna 1 x Bracket 1 x Set of Installation Srews 1 x EU Power Supply (Come with an adapter according to your country~) 1 x User Manual   Details pictures:

Output voltage: DC 5V / 3.3V ATmega328P No USB cable version This version can not compatible with OS system Features: Open the original schematic design, free development software interface download, also allow your needs to be modified, easy and convenient to download the program. Can simply use sensors, all kinds of electronic components connection (such as LED lights, buzzer, buttons and photosensitive resistance, etc.), make all sorts of interesting work. Using high-speed microprocessor controller (ATMEGA328), development interface and environment are all very simple, easy to understand, very suitable for beginners to learn. Description: Digital I / O: 0 - 13 Analog I / O: 0 - 5 Support ISP download function Input voltage: DC 5V ~ 9V (No external power supply when connected to the computer) Output voltage: DC 5V / 3.3V Using Atmel Atmega328 microprocessor controller How to use: 1. Download the IDE arduino Link: http: http://arduino.cc/en/Main/Software (Copy to open) 2. Download the USB chip driver Link: http://www.5v.ru/zip/ch341ser.zip (Copy to open) 3. Plug in UNO development board, the driver will be installed automatically 4. Select the UNO from the die 5. Select the COM port 6. The best choice first, arduino come with routine procedures, burn into it. Package included: 5 x UNO R3 Development Board