Original board

Original T-con Logic Board T370XW02 VC 37T03-C01 LCD Controller LA37A350C1 Features: Original T-con board LCD controller T370XW02 VC 37T03-C01 Size: 13 x 5.8 cm Weight: 24g Package included: 1 x T370XW02 VC 37T03-C01 LCD controller

Original Banana Pi G1 Open Debugger Board Burner ModuleIntroduction: Open Debugger is a set of programming tools in the development of STM series of microcontrollers, TI CC1x, 2x, TI CC3x series SOC, when STC Series MCU can be programmed quickly and easily debug, debugging programmer does not have to do something different series of chips switching plug tedious work.It is also one of USB2.0 HUB, making it easy to extend to other USB tools.With it, no longer need to face a bunch of different writer, complicated mess of wiring, USB port deficiencies. Operating Condition: Operating voltage: DC 5VOperating temperature: 0°C to 85°CThe onboard voltage output: 3.3 VMaximum output current: 2000 mASupported operating systems:Microsoft Windows 2000Windows XP SP2/SP3 operating system (32-bit versions)Windows Vista operating system (32 and 64 bit)Windows 7 operating system (32 and 64 bit)Windows 8 operating system (32 and 64 bit) Support Objects: a)CC Debugger Interface: Programming and debugging of the following 8051-based TI SoCs: CC1110, CC1111 CC2430, CC2431 CC2510, CC2511 CC2530, CC2531, CC2533 CC2540, CC2541 CC2543, CC2544, CC2545Control the same apparatus to SmartRF Studio. In addition, you can also control the following transceiver SmartRF: CC1120, CC1121, CC1125, CC1175 CC1100, CC1101, CC110L, CC113L, CC115L CC2500, CC2520It can also be used to program the PurePath wireless devices: CC8520, CC8521 CC8530, CC8531 b)SWD Interface: Programming and debugging mainstream ARM7 9 11, Cortex-A5 A8 A9 M0 M1 M3 M4Supported MCU manufacturers:ST, Freecale, Nuvoton, NXP, TI, Cypress, Atmel, Analog, Fujitsu, Toshiba, Energy Micro...Speeds up the programming and debugging functions 4Mhz: Write Flash Rom, EEPROM, ARF, and support for full speed, stepping, breakpoints c)JTAG Interface: JTAG programming and debugging interface for all supported kernel. d)UART Interface: STC series microcontroller programming and debugging output port for printing information. Package included: 1 x Original Banana Pi G1 Open Debugger Acronym table CSn Chip Select (active low) DC Debug Clock DD Debug Data RST Debug Reset DUT Device Under Test GND Ground LED Light Emitting Diode MISO Master In Slave Out MOSI Master Out Slave In RF Radio Frequency SCLK Serial Clock SoC System-on-Chip SPI Serial Peripheral Interface USB Universal Serial Bus Target Positive voltage on target CLK SWD Clock DIO SWD DATA Input/Output TMS JTAG Test Mode Select TCK JTAG Test Clock Input TDO JTAG Test Data Output TDI JTAG Test Data Input SRST JTAG Test Reset Input, Active Low RXD USB Serial Input TXD USB Serial Output

Original Banana PI BPI-M1+ Plus Dual Core A20 1GB RAM WiFi Module Hardware: Soc: Allwinner A20     CPU: ARM Cortex-A7 Dual-Core 1 GHz (ARM v7 instruction set)     GPU: Mali400MP2 Complies with OpenGL ES 2.0/1.1 (hardware acceleration support)     SDRAM: 1GB DDR3(shared with GPU)     Power: 5V/2A via MicroUSB (DC in Only) and /or Micro USB (OTG)     PMU: AXP209 Features: Low-level perpherials 40 Pins Header, 28xGPIO, some of which can be used for specific functions including UART, I2C, SPI, PWM, CAN, I2S, SPDIF, LRADC, ADC, LINE-IN, FM-IN, HP-IN On board Network 10/100/1000Mbps ethemet(Realtek RTL8211E/D) Wifi Module Wifi 802.11 b/g/n Bluetooth Optional On board Storage Micro SD(TF) Card,SATA 2.0 Display HDMI 1.4 (Type A -full) LVDS/RGB/CPU display interface (DSI) for raw LCD panels Composite Video (PAL and NTSC) (via 3.5mm TRRS jack shared with audio out) 11 HDMI resolutions from 640x480 to 1920x1080 plus various PAL and NTSC standards Video HD H.264 2160p video decording Multi-format FHD video decording,including Mpeg 1/2,Mpeg4,H.263,H.264,ect H.264 high profile 1080p@30fps or 720p@60fps encording Audio outputs HDMI,analog audio(via 3.5mm TRRS jack shared with composite video out),I2S audio (also potentially for audio input) Camera Parellel 8-bit camere interface Audio input On board microphone USB 2USB 2.0 host,1 USB 2.0 OTG (all direct from A20 chip) Buttons Reset button, Power button, U-boot button Leds Power status led(red), User defined led1(green), User defined led2(blue) Other IR receiver Size 92 x 60mm Weight 45g Package included: 1 x Banana Pi M1+

Original Banana Pi G1 Open Debugger Board Burner Module Package contains 1 X item of the smallest listed variant.

DSO Shell (DSO150) Oscilloscope DIY Kit: 1. DSO Shell has similar bandwitch as DSO138 though it contains significant improvements in structure, mechanical, and operation. 2. Display and MCU are now mounted on the same board (mainboard) to avoid using inter-board pin-headers. Feedback from DSO138 usres have shown that soldering on the pin-headers are often problematic for many beginners. Analog channel is placed on a separated board which contains most user install parts. This brings in better separation between analog and digital circuits. Without the analog portion the mainboard is actually a general purpose control board that can be used in many other applications. The mainboard is fully installed (except a few through-hold components) and factory tested before packing. 3. DSO Shell comes with full enclosure. The front panel and top/bottom brackets are flexiable for easy user modification. 4. Rotary encoder has been added. It makes parameter adjustment much quicker and easier. 5. The sensitivity of DSO Shell has been extended in both directions and is higher and wider than DSO138. It reaches 5mV/div --- 20V/div while DSO138 is only 10mV/div --- 5V/div. 6. DSO Shell runs on 9V (do not use power voltage higher than 10V!) power supply. Users need to prepare their own power supply since it is not included in the kits. The power jack on the mainboard accepts standare 5.5mm/2.1mm DC plug. Alternative 2-pin connector (0.1" pitch) is also provided for convenience to connect to different power sources. Important Notes: It is assumed that users have adaquate soldering skills and troubleshooting skills to assemble the DSO Shell kits. Buyers are advised that due to skills of user is involved in assembly it is not guaranteed every kit will end up being a working device. But we will make as much efforts as we can to approach that goal. After receiving the kits users are urged to check mainboard and LCD by applying proper power supply. Report immediately to us or JYE Tech if problem or damage is found. For 15002 K kit SMD component soldering skills are required (is more difficult than 15003 K version, please note). SMD parts does not soldered on analog board. Characteristics of indicators: Number of channel: 1 Analog bandwidth: 0 - 200KHz Sensitivity: 5mV/Div - 20V/Div Sensitivity error: Resolution: 12-bit Input Impedance: 1M ohm Maximum input voltage: 50Vpk Coupling: DC, AC, GND Max real-time sampling rate: 1Msps Timebase: 10us/Div - 500s/Div Record length: 1024 Trigger modes: Auto, Normal, Single Trigger types: Rising/falling edge Trigger position: 1/2 of buffer size fixed 2.4-inch color TFT LCD with 320 x 240 resolution 9V DC (8 - 10V acceptable) Supply current: 120mA @ 9V Dimension: 115mm x 75mm x 22mm Weight: 100 gram (not including cables and power supply) Package includes: 1 x DIY DS0150 Digital Oscilloscope Kit (There may be a color difference in the shell) 1 x EN Instruction SMD parts does not soldered on analog board. Finish and test pictures, for reference only:

Hardware: Soc: Allwinner A20 CPU: ARM Cortex-A7 Dual-Core 1 GHz (ARM v7 instruction set) GPU: Mali400MP2 Complies with OpenGL ES 2.0/1.1 (hardware acceleration support) SDRAM: 1GB DDR3(shared with GPU) Power: 5V/2A via MicroUSB (DC in Only) and /or Micro USB (OTG) PMU: AXP209 Features: Low-level perpherials 40 Pins Header, 28xGPIO, some of which can be used for specific functions including UART, I2C, SPI, PWM, CAN, I2S, SPDIF, LRADC, ADC, LINE-IN, FM-IN, HP-IN On board Network 10/100/1000Mbps ethemet(Realtek RTL8211E/D) Wifi Module Wifi 802.11 b/g/n Bluetooth Optional On board Storage Micro SD(TF) Card,SATA 2.0 Display HDMI 1.4 (Type A -full) LVDS/RGB/CPU display interface (DSI) for raw LCD panels Composite Video (PAL and NTSC) (via 3.5mm TRRS jack shared with audio out) 11 HDMI resolutions from 640x480 to 1920x1080 plus various PAL and NTSC standards Video HD H.264 2160p video decording Multi-format FHD video decording,including Mpeg 1/2,Mpeg4,H.263,H.264,ect H.264 high profile 1080p@30fps or 720p@60fps encording Audio outputs HDMI,analog audio(via 3.5mm TRRS jack shared with composite video out),I2S audio (also potentially for audio input) Camera Parellel 8-bit camere interface Audio input On board microphone USB 2USB 2.0 host,1 USB 2.0 OTG (all direct from A20 chip) Buttons Reset button, Power button, U-boot button Leds Power status led(red), User defined led1(green), User defined led2(blue) Other IR receiver Size 92 x 60mm Weight 45g Package included: 1x Banana Pi M1

Buy Original Xiaomi Mijia Power Socket Strip 4 Sockets Big Plug Extension Patch Board with 4 Control... for R435.90

An Original Dyeline Print used in the production of George Lucas' classic:The empire strikes back and Return of the Jedi. This is an early working production copy of the blueprint.It comes framed and glazed in a laser cut mount board with the movie logo and a screen still. This display is in good condition.

Original Arduino UNO R3 Development Board ATmega328 microcontroller Input voltage - 5V from USB connection or 7-12V additional power connector - onboard voltage regulator USB - Large Printer Cable Connector 14 Digital I/O Pins (6 PWM outputs) 6 Analog Inputs We keep local stock. Collections also possible in Pretoria.    

Mega2560 R3 ATMEGA2560-16AU + CH340 Board With USB For Arduino Feature: This board is completely solve the traditional 2560 board is not compatible with win7 and win8 system instability. Retains the main chip ATMEGA2560-16AU, replacing the usb chip-16U2, in most applications, these USB interface chips only as a serial "brush "and communication. With professional usb chip, not only can reduce the cost, but also can meet applications. Note: This version is optimized in the original version, mainly designed for customer need high product quality and function, not only consistent and compatible with the original, but also easy to use. This version is not suitable for 3D printer, if you need this function please buy SKU074519 (Click here) Method of use: 1. Download the arduino IDE Download address: http://arduino.cc/en/Main/Software (copy open) 2. Download the USB chip driver Download address: http://www.wch-ic.com/download/list.asp? Id = 126 3. Plug in the NANO development board, the driver is automatically installed 4. Select NANO in die 5. Select the COM port, this can query in "my computer" Package included: 1 x MEGA2560 R3 Board

Mega2560 R3 ATMEGA2560-16AU + CH340 Board For Arduino Without USB Feature: This board is completely solve the traditional 2560 board is not compatible with win7 and win8 system instability. Retains the main chip ATMEGA2560-16AU, replacing the usb chip-16U2, in most applications, these USB interface chips only as a serial "brush "and communication. With professional usb chip, not only can reduce the cost, but also can meet applications. Note: This version is optimized in the original version, mainly designed for customer need high product quality and function, not only consistent and compatible with the original, but also easy to use. This version is not suitable for 3D printer, if you need this function please buy ID: 73020 (Click here) THis version does not includes USB cable Package included: 1 x MEGA2560 R3 Board

Buy 3pcs Original Ai-Thinker CP2102 ESP-12E NodeMCU Lua WiFi Test Board Development Board Based on ESP82 for R532.00

Buy 5pcs Original JYETech WAVE2 Interface Board with Uart-USB Converter Module CH340G for R849.50

Arduino-Compatible R3 UNO USB Board + Acrylic Experimental Platform Arduino-Compatible R3 UNO ATmega16U2 AVR USB Board Description: UNO R3 board is 100% compatible with original Arduino, now it has perfect quality and performance. Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements theProcessing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux). This is the new Tosduino Uno R3. In addition to all the features of the previous board, the Uno R3 now uses an ATmega16U2 instead of the ATmega8U2 chip. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. Note:  The TOSduino Uno R3 requires the Arduino 1.0 drivers folder in order to install properly on some computers. We have tested and confirmed that the R3 can be programmed in older versions of the IDE. However, the first time using the R3 on a new computer, you will need to have Arduino 1.0 installed on that machine. The small chip is ATmega16U2, the 28 pin DIP socket chip is ATmega328-pu. Interaction: 2013-08-08 Cathal Keady's question: Can item SKU066313 be powered directly from using the USB port or do I need to purchase a power supply for it. my answer: This item has not built-in battery, so it can not be charged. With that USB cable connect to computer, you can use it. There is no need of power supply. Acrylic Experimental Platform For Arduino UNO R3 Board Fixation Description: Apply to all of the same mounting holes with the arduino board Size: 12CM x 8.3CM Notice: Motherboard installed near the SDA and SCL foot nylon column cannot be fixed screw or nut, please don't think that is a design problem Package included: 1 x UNO R3 1 x USB cable 1 x Dianegative 4 x screw 4 x Silica gel pads (NOT included the breadboard)

Geekcreit™ UNO R3 ATmega328P Board + 2.4 Inch TFT LCD Touch Screen Module For Arduino Note: The 2.4 inch LCD Touch Screen Module is the newest version which has more stable chip with touch pen. (Update in 2015-09-17, CN warehouse at present) Please pay close attention to the bottom of the forum, we will post the most newest driver there, if your LCD screen can not work, please contact us to get the useful driver, thank you! UNO R3 ATmega328P Board: Description: UNO R3 board is 100% compatible with original Arduino, now it has perfect quality and performance. Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements theProcessing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux). This is the new Tosduino Uno R3. In addition to all the features of the previous board, the Uno R3 now uses an ATmega16U2 instead of the ATmega8U2 chip. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. Note: The TOSduino Uno R3 requires the Arduino 1.0 drivers folder in order to install properly on some computers. We have tested and confirmed that the R3 can be programmed in older versions of the IDE. However, the first time using the R3 on a new computer, you will need to have Arduino 1.0 installed on that machine. The small chip is ATmega16U2, the 28 pin DIP socket chip is ATmega328-pu. Interaction: 2013-08-08 Cathal Keady's question: Can item SKU066313 be powered directly from using the USB port or do I need to purchase a power supply for it. my answer: This item has not built-in battery, so it can not be charged. With that USB cable connect to computer, you can use it. There is no need of power supply. 2.4 Inch TFT LCD Touch Screen Module: Features: 2.4 inch LCD TFT display Colorful, 18-bit 262,000 different shades 4-wire resistive touchscreen 240 x 320 resolution Spfd5408 controller with built in video RAM buffer 8 bit digital interface, plus 4 control lines Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3 and analog 4 and 5. Pin 12 is available if not using the micro SD 5V compatible, use with 3.3V or 5V logic Size: 71 x 52 x 7mm Package included: 1 x UNO R3 ATmega328P Board with USB 1 x 2.4 Inch TFT LCD Touch Screen Module with touch pen

Features: 1. Type: 6j1 tube 2. Power input: AC 12V 1A, 5.5*2.5 plug 3. Channle:2.0 / stereo 4. Potentiometer Role: Volume adjustment + Power Switch 5. Size: 77 x 75 x 52mm Note: This is DIY Kits, and you need to assembled it by yourself. Specification: FE-6J1-2 fever tube pre-amp board is the circuit schematic design imitation crew Music fax X-10D,to be rational optimization,more stable performance than the original machine,tube play 10% increase. This board uses a single 12V AC input,the circuit processing provides 6J1 tube needed positive and negative voltage and filament power supply voltage. Power works: an open power tube filament heating is started,when the boost from the zero-voltage start boosting hot filament tube,etc.,also happens to boost boosting finish,so this is the same with the guts rectification,8*470UF the capacitor filter very clean,good power supply system will not have a hum,the filament is 12V DC power supply,need two filament tube is connected in series with a DC filament also in order to reduce the noise. Instructions: 6J1 Tube Buffer 0.85 times magnification, connected between the source and before or after class, can effectively filter digital flavor. 1. AC 12V input: The DC3.5 / 5.5 * 2.1 socket, 12V AC power adapter, if you use non-plug AC 12V transformer, power cord need to solder on the circuit board. Remember: You can not use a DC power input, otherwise it does not work! 2. the left-channel input / right channel input: audio signal input, can be connected to mobile phones, computers, M3, the MP4, and other music players. 3. the left channel output / right channel output: an audio signal output terminal can be connected to the audio signal input amplifier, power amplifier board. 4. the power switch / volume knob: turn the knob counter-clockwise to decrease the volume beginning, when the volume down to the minimum, if it continues to rotate until the "ticking" sound, then the power off, the light goes off; in the closed state, Turn the knob clockwise to hear "tick" sound, light is on, the power is turned on, then the volume is minimal, then continue clockwise rotation is to increase the volume. Package included: 1 x 6J1 value preamp amplifier board diy kits

UNO R3 ATmega328P Board: Description: UNO R3 board is 100% compatible with original Arduino, now it has perfect quality and performance. Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements theProcessing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux). This is the new Tosduino Uno R3. In addition to all the features of the previous board, the Uno R3 now uses an ATmega16U2 instead of the ATmega8U2 chip. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. Note: The TOSduino Uno R3 requires the Arduino 1.0 drivers folder in order to install properly on some computers. We have tested and confirmed that the R3 can be programmed in older versions of the IDE. However, the first time using the R3 on a new computer, you will need to have Arduino 1.0 installed on that machine. The small chip is ATmega16U2, the 28 pin DIP socket chip is ATmega328-pu. 2.8 Inch LCD Display Feature: Description: 2.8 inch LCD TFT display Bright, 4 white-LED backlight Colorful, 18-bit 262,000 different shades 4-wire resistive touchscreen 240 x 320 pixels with individual pixel control No wiring, no soldering. Simply plug it in and load library On-board 3.3V 300mA LDO regulator 5V compatible, use with 3.3V or 5V logic Support 2GB micro SD TF card Size: 7.8 x 5.3cm Package included: 1 x 2.8 Inch TFT LCD Shield Touch Display Module 1 x UNO R3 ATmega328P Board with USB cable

UNO R3 ATmega16U2 AVR Module Board For Arduino Without USB Cable Description: UNO R3 board is 100% compatible with original Arduino, now it has perfect quality and performance. Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements theProcessing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux). This is the new Tosduino Uno R3. In addition to all the features of the previous board, the Uno R3 now uses an ATmega16U2 instead of the ATmega8U2 chip. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. Note: The TOSduino Uno R3 requires the Arduino 1.0 drivers folder in order to install properly on some computers. We have tested and confirmed that the R3 can be programmed in older versions of the IDE. However, the first time using the R3 on a new computer, you will need to have Arduino 1.0 installed on that machine. The small chip is ATmega16U2, the 28 pin DIP socket chip is ATmega328-pu. Note: This version does not includes USB cable Interaction: 2013-08-08 Cathal Keady's question: Can item SKU066313 be powered directly from using the USB port or do I need to purchase a power supply for it. my answer: This item has not built-in battery, so it can not be charged. With that USB cable connect to computer, you can use it. There is no need of power supply. Package included: 1 x UNO R3 module

PRO-mounts Board Kit Product Description PM2015GP1051 Kit, ALL boards Weather you fly your Kite, ride your Surf board, Skate a ramp, jump Wakes, peddle your SUB or downhill your Snowboard or Ski￯﾿ﾽs, the PRO-mounts Board Kit gives you an all in 1 solution. A Large white Board mount with Safety Leash, 6 Anti Fog inserts to keep the fog out in combination with a buckle lock & bright orange Floaty to keep things secure in case of loss. - ALL PRO-mounts products are guaranteed for LIFE (lifetime warrantee) - ALL PRO-mounts products are compatible with ALL GoPro, Yi, SJ Cam, Sony / Nikon / Ricoh (camera adapter needed), Eken, SJ Cam, SooCoo, Garmin and many more brands - ALL PRO-mounts products are supplied as COMPLETE set NO other parts needed to use Our Guarantee to You We guarantee the utmost in Quality, Authenticity and Customer Satisfaction All our Items are Brand New and 100% Authentic with Original Box and Papers Price Beat or Match, if we can't (which is hardly ever), we will give you R150 off your next order with us. At these prices stocks are very limited, so order now to avoid disappointment Please view our other listings HERE Looking for something that we have not listed. Let us know - Will will get the best price for you

Geekcreit™ UNO R3 ATmega328P Development Board For Arduino Output voltage: DC 5V / 3.3V ATmega328P No USB cable version This version can not compatible with MAC OS system   Features: Open the original schematic design, free development software interface download, also allow your needs to be modified, easy and convenient to download the program. Can simply use sensors, all kinds of electronic components connection (such as LED lights, buzzer, buttons and photosensitive resistance, etc.), make all sorts of interesting work. Using high-speed microprocessor controller (ATMEGA328), development interface and environment are all very simple, easy to understand, very suitable for beginners to learn. Description: Digital I / O: 0 - 13 Analog I / O: 0 - 5 Support ISP download function Input voltage: DC 5V ~ 9V (No external power supply when connected to the computer) Output voltage: DC 5V / 3.3V Using Atmel Atmega328 microprocessor controller How to use: 1. Download the IDE arduino    Link: http: http://arduino.cc/en/Main/Software (Copy to open) 2. Download the USB chip driver    Link: (Copy to open) 3. Plug in UNO development board, the driver will be installed automatically 4. Select the UNO from the die 5. Select the COM port 6. The best choice first, arduino come with routine procedures, burn into it. Package included: 1 x UNO R3 Development Board

Description: Input: 100-240V 50-60Hz Output: 12V Output current: 1A Size: 5.6 x 3.5 x 1.9cm Type: original disassemble bare board Package included: 1 x 12V 1A switching power supply bare board

Teensy++ 2.0 Compatible USB AVR Development Board For Arduino ISP AT90USB1286 Features: USB can be any type of device AVR processor, 16 MHz Single pushbutton programming Easy to use Teensy Loader application Free software development tools Works with Mac OS X, Linux & Windows Tiny size, perfect for many projects Available with pins for solderless breadboard Very low cost & low cost shipping options How to use: Teensy.exe can be downloaded directly from the Internet without having to install the driver, directly write, program and verification. Do not need to buy another expensive burner. You can also use the arduino IDE installation Teensy development environment. Note: This board does not original. Package included: 1 x Teensy++ 2.0 USB AVR Development Board

TB6560 3A CNC Router 1 Axis Driver Board Stepper Motor Drivers   is available now from our US   warehouse Free shipping to US  in 3-6 business days ship to Canada, Brazil in 7-10 days TB6560 3A CNC Router 1 Axis Driver Board Stepper Motor Drivers Specification: Size: 75 x 50 x 35mm / 2.95 x 1.96 x 1.37inch (L x W x H) Rated maximum output: ± 3A, peak 3.5A Working voltage: DC 10V-35V Recommended to use a switching power supply: DC24V power supply Subdivision: whole step, half-step, step 1/8, 1/16 step, a maximum of 16 Subdivisions. Feature: Using the Toshiba TB6560AHQ new original chip with low voltage shutdown, overheating stop and over current protection circuit to ensure optimal performance. For two-phase within 42, 57 stepping 3A / four-phase / of line four / six-wire stepper motor, and is not suitable for more than 3A stepper motor. Automatic half current function. 6N137 high-speed optical coupling, guarantee high speed without losing step. Features similar products: 1. Current grade-by-adjustable to meet your demand for a variety of applications. 2. Semi-automatic flow adjustable. 3. 6N137 high-speed optical coupling, guarantee high speed without losing step. 4. Plate printed setup instructions operation without manual also. 5. Thick teeth radiator, good heat dissipation. Package included: 1 x TB6560 1 axis driver board  

Teensy 2.0 Compatible USB AVR Development Board For Arduino ISP ATMEGA32U4 Features: USB can be any type of device AVR processor, 16 MHz Single pushbutton programming Easy to use Teensy Loader application Free software development tools Works with Mac OS X, Linux & Windows Tiny size, perfect for many projects Available with pins for solderless breadboard Very low cost & low cost shipping options How to use: Teensy.exe can be downloaded directly from the Internet without having to install the driver, directly write, program and verification. Do not need to buy another expensive burner. You can also use the arduino IDE installation Teensy development environment. Note: This board is not original. Package included: 1 x Teensy 2.0 compatible USB AVR Development Board

Description: Board categories: Original disassemble circuit board Input voltage: 100-240V 50-60HZ Output voltage: 24V Output current: 5A Function: over-voltage / over-current / short circuit protection Size: 13.5 x 5 x 2.6cm Package included: 1 x 24V 5A switching power supply bare board

Description: Input: 100-240V 50-60Hz Output: 12V Output current: 1A Size: 5.6 x 3.5 x 1.9cm Type: original disassemble bare board Package included: 5 x 12V 1A switching power supply bare board

Description: Board categories: Original disassemble circuit board Input voltage: 100-240V 50-60HZ Output voltage: 12V Output current: 2A Function: over-voltage / over-current / short circuit protection Size: 6.6 x 4 x 2.15cm Package included: 10 x 12V 2A switching power supply bare board

Description: Board categories: Original disassemble circuit board Input voltage: 100-240V 50-60HZ Voltage: 6V Current: 2A Size: 6.4 x 3.5 x 2.0cm Function: over-voltage / over-current / short circuit protection Package included: 10 x 6V 2A switching power supply bare board

Description: UNO R3 board is 100% compatible with original Arduino, now it has perfect quality and performance. Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements theProcessing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux). This is the new Tosduino Uno R3. In addition to all the features of the previous board, the Uno R3 now uses an ATmega16U2 instead of the ATmega8U2 chip. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. Note: The TOSduino Uno R3 requires the Arduino 1.0 drivers folder in order to install properly on some computers. We have tested and confirmed that the R3 can be programmed in older versions of the IDE. However, the first time using the R3 on a new computer, you will need to have Arduino 1.0 installed on that machine. The small chip is ATmega16U2, the 28 pin DIP socket chip is ATmega328-pu. Note: This version does not includes USB cable Interaction: 2013-08-08 Cathal Keady's question: Can item SKU066313 be powered directly from using the USB port or do I need to purchase a power supply for it. my answer: This item has not built-in battery, so it can not be charged. With that USB cable connect to computer, you can use it. There is no need of power supply. Package included: 3 x UNO R3 module