G3 12v normally

Description: Electric Solenoid Valve For Water Air N/C 12V DC 1/2Inch Normally Closed Suitable for use in water and low viscosity fluid applications. If your central heating or irrigation sprinkler system isn't working correctly it could be down to the solenoid valve. Repair a faulty valve with this brand new, fast acting 12V DC diaphragmstyle replacement. Specification: Voltage: 12V DC Inlet and outlet: hose barbs for 1/2" (outer diameter) hose Pressure: 0.02 0.8Mpa Max fluid temperature: 95°C Operation mode: normally closed Valve type: diaphragm (operated by Servo) Usage: water and low viscosity fluids Please note it is not suitable for use with gravity fed systems Package included: 1 x 12V 1/2" Electric Solenoid Valve Details pictures:

Feature: This module is widely applicable to the design and development of home electronics and electronics products for the electronics enthusiasts. It can be used as a signal input source of the SCM, and is especially suitable for the design of electronic circuits for students in universities and colleges. Can be docked with a single chip, or an amplifying drive relay or a small DC motor. Module board with self-locking, interlocking, triggering (inching), high level, low level, machine equipment, automation equipment modification, PLC industrial control, Arduino robot, intelligent product Product introduction: Each road has a signal light to clearly know which switch is working. There are three options for self-locking/interlocking/trigger (jog). The self-locking is pressed once, the relay pulls in, press again to closed. The self-locking type 6 channels are independent of each other, and can also be connected to an external trigger switch (CH connection terminal), triggered by a high or low level (optional), and can control 6 channels at the same time, such as lighting control. When the trigger (jog) is pressed, the relay pulls in and releases to closed. It is also possible to connect an external trigger switch (CH terminal connection) with a high or low level trigger (optional). Applicable to such as electric gates, electric door locks, and MCU docking only need a high or low pulse circuit and other circuits. The interlock is a typical application of the fan design. When press S1, the relay pulls in; when press S2, S1 disconnect, the relay of S2 pulls in. The 2 channel interlock can only be connected one way, and it can also be connected to an external trigger switch (CH connection terminal), triggered by a high or low level (optional). Practical applications such as electric fan gear switch circuit. Features: 1. Double-sided design PCB, 6 channel independent design, mutual interference; 2. The use of single-chip design, stable and reliable performance, strong anti-interference, will not trigger falsely, superior performance; 3. Humanized interface design, with a good terminal, can be directly connected to the lead; 4. The trigger end has optocoupler isolation, the trigger power supply can be independent external power supply, truly completely isolated; 5. With 6 tactile switches as product testing, direct test product stability; 6. With power indication (green LED) and 6 switch indications (red LED); 7. The relay control the load, and the load can withstand under 250V 10A (AC) and 30V 10A (DC); 8. Module size: 110x57x18.5mm, weight: 100g; 9. Design has 4 bolt holes: spacing 104x51, aperture 3mm. Electrical parameters: Trigger voltage: It is 12V voltage trigger, needs to connect a 5.1-6.8K resistor in series to trigger, otherwise it will burn the chip. Supply voltage: 12V DC Quiescent current: 23mA Operating current: 1 channel 69mA 2 channel 116mA 3 channel 162mA 4 channel 207mA 5 channel 252mA 6 channel 297mA Load: 250V 10A (AC) or 30V 10A (DC) Module interface: Power input: 1. DC+: positive power supply for the module, the same voltage as the relay; 2. DC-: module power negative; Trigger side: 1. CH1-CH6: Corresponding to 1-6 relay trigger control terminal, support high or low level trigger trigger; 2. TRV+: external positive trigger power supply, if you want to connect external trigger power, the jumper between RTV+ and VCC should be unplugged 3. TRV-: external negative trigger power supply, if you want to connect external trigger power, the jumper between RTV- and GND should be unplugged 4. 6 micro switches: Corresponds to 1-6 relay test keys, valid at low-level trigger; 5. High/low level trigger selection. When COM and L are connected, low level trigger is valid. When COM and H are connected, high level trigger effective Relay output: 1. NO1-NO6: Relay normally open interface, before pull-in the relay is vacant, after pull-in, short circuit with COM. 2. COM1—COM6: Relay common interface 3. NC1—NC6: Normally closed relay interface, before pull-in the relay short circuit with COM, after pull-in the relay is vacant. Package includes: 1 x 12V 6 Channel Relay Module

Specifications: Color:White Ozone Output: 10g Input Voltage: DC 12V Working power: ≈ 95w Operating frequency: 16kHz Noise: 20 (dB) Operating temperature: -10 Celsius -60 Celsius Humidity: 35% -85% RH Storage temperature: -20 Celsius -70 Celsius Power Dimensions:13.5 x 5.0 x 8cm Ceramic Dimensions: 10x4.7cm Cable Length: Approx. 73cm(28.74”) Features: - Ozone sterilization, no residue of toxic substances. - Eliminates odors, freshens stale air. - Low power consumption,safe, quiet and efficient. - One car sterilization time only need three to eight minutes,very efficient. - Mini size, portable and easy to operate. Precautions: 1. Ozone main role is in addition to formaldehyde, odor, smoke. 2. Ozone disinfection is the moment, one car sterilization time is three to eight minutes. 3. Do not touch the ozone sheet while working. 4. Open disinfection automotive air conditioning, air conditioning can be associated together disinfection, odor removal air conditioning. 5. Normally Using this ozone generator for 10 to 20 minutes each time; if using it for more than 20 minutes, you had better use an electrical fan. Packaged included: 1 x Ozone Generator More details:

OPTIONS: 14x14mm: 218 Available. Specifications: Powered form: Interrupted Unlock time: 1 second Power: DC 12V Input Current: 0.34A; Cable Length: 120mm Approximate Dimensions: Length - 27mm; Width - 15mm; Height - 17mm; Tongue Length - 7mm; Tongue Height - 10mm Instructions: 1)Connect the Red wire to positive and the green wire to negative. 2)Turning the current on will unlock and turning it off will lock the mechanism. Features: ●Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. ●When the coil is energised, the slug is pulled into the center of the coil. ●It's basically an electronic lock, designed for a cabinet, safe or door (please check the size). ●Normally the lock is active so you can't open the door because the solenoid slug is in the way. It does not use any power in this state. When the current is applied, the slug pulls in so it doesn't stick out anymore and the door can be opened. Package Included: 1 x Electronic Lock Catch More Details:

SELECTED OPTION: SIZE: 14X14MM CLICK HERE for more options in this item. Specifications: Powered form: Interrupted Unlock time: 1 second Power: DC 12V Input Current: 0.34A; Cable Length: 120mm Approximate Dimensions: Length - 27mm;                                      Width - 15mm;                                      Height - 17mm;                                      Tongue Length - 7mm;                                      Tongue Height - 10mm Instructions: 1)Connect the Red wire to positive and the green wire to negative. 2)Turning the current on will unlock and turning it off will lock the mechanism. Features: ●Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. ●When the coil is energised, the slug is pulled into the center of the coil. ●It's basically an electronic lock, designed for a cabinet, safe or door (please check the size). ●Normally the lock is active so you can't open the door because the solenoid slug is in the way. It does not use any power in this state. When the current is applied, the slug pulls in so it doesn't stick out anymore and the door can be opened. Package Included: 1 x Electronic Lock Catch More Details:

Specifications: Powered form: Interrupted Unlock time: 1 second Power: DC 12V Input Current: 0.34A; Cable Length: 120mm Approximate Dimensions: Length - 27mm; Width - 15mm; Height - 17mm; Tongue Length - 7mm; Tongue Height - 10mm Instructions: 1)Connect the Red wire to positive and the green wire to negative. 2)Turning the current on will unlock and turning it off will lock the mechanism. Features: ￢ﾗﾏSolenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. ￢ﾗﾏWhen the coil is energised, the slug is pulled into the center of the coil. ￢ﾗﾏIt's basically an electronic lock, designed for a cabinet, safe or door (please check the size). ￢ﾗﾏNormally the lock is active so you can't open the door because the solenoid slug is in the way. It does not use any power in this state. When the current is applied, the slug pulls in so it doesn't stick out anymore and the door can be opened. Package Included: 1 x Electronic Lock Catch More Details:

SELECTED OPTION: PLUG: EUPLUG CLICK HERE for more options in this item. Specifications: Battery Type: Lead Acid Battery Input parameters: AC100-250V 47/63Hz Output parameters: 12-14.6V 1A Charging current: 1000mA Dimensions: 85*48*30mm Control Mode: IC Control Intelligent Positive Voltage Detection Timer: None Indicator (LED): Green light - no battery or charging completed; red light - charging Efficiency: >80% (Max.load) Operating temperature range: -10--40°C Humidity: 30%--85% Storage temperature: -20°C--70°C Storage humidity: 30%--90%   Features: -Limit voltage protection The charger output voltage will not exceed the maximum charge voltage of the set battery. Constant pressure. -Current Limit Protection The charger output current will not exceed the set battery maximum charge current. Constant current. -Short Circuit Protection When the output is short-circuited, the charger cannot work normally and the output returns to normal. The charger can recover automatically. -Reverse connection protection The charger will not work when the output cable is reversed. It will not start until the user connects correctly.  -Accurate positive voltage detection ensures that the battery is fully charged without overcharging. -Precise constant current control, the current change amplitude is less than 5%. -Built-in high-quality and high-efficiency switching power supply, adopting environmentally-friendly green power control technology, making the temperature rise small and light. -Two-color indicator light, clear indication, the current status at a glance. -Short circuit protection function, the short circuit current is zero, allowing long-term short circuit without damaging the host. Packaged included: 1 x Motorcycle Smart Battery Charger More details:  

Description: DC 12V G3/4 DN20 Normally Closed Release Valve 6 Points For Drinking Fountain Washing   Specification: Rated voltage: DC12V Wattage: 5W Relative humidity: ≤95% Coil resistance: 37Ω ± 0.8Ω Working pressure: 0-0.02Mpa Wnvironment temperature: + 1 ℃ ~ + 45 ℃ Water temperature: 0 ℃ ~ + 100 ℃ Storage and transport of temperature: - 30 ℃ ~ + 60 ℃;   Features: 12V normally closed release valve Normally closed-always open when valve power ups Release valve-Refers to the working pressure   Package included: 1pc x DC 12V Normally Closed Release Valve   Notice:  1. Please allow a bit error due to manual measurement. please make sure you do not mind before you bid. 2. The color may have different as the difference display, pls understand.   More Details:

Specification: Rated voltage: DC 12V Current: 120mA External diameter: 5.5mm Inner hole: 3.2mm Cable length: approx 33.5cm Work mode: Normally Closed 7PSI pressure time flow: 11L/min Weight: 50g Fitment: Micro electric water valve, Micro exhaust valve, Automatic control watering.   Package includeds: 1 x Solenoid Exhaust Valve   Details pictures:

ITEM DETAILS This is the G3 version of the Ray Technology gaming mouse and features a unique wood grain look. The back light has six colours, white, teal, purple, yellow, red and orange. Mouse Specifications: USB interface DPI Switch Six buttons and a scroll wheel LED back light Intelligent connectivity (plug and play) INTERNATIONAL SHIPPING Once you have made your purchase please allow for 2-3 business days for us to package and ship your item. Once it is shipped you will receive a tracking number with China Post. Delivery time can differ wildly depending on the time of the year and how easily your parcel passes through customs. As a guide I would plan for 4 to 6 weeks (and you will hopefully be pleasantly surprised when it arrives earlier). Please be aware that customs and the nature of the international postal system can cause significant delays which are out of my control. CUSTOMS AND IMPORT TAX If your parcel is valued at under R500 it is exempt from duty and will normally not be worth the administration costs to charge VAT on. For more information on possible fees for high value items you should contact South African customs. PAYMENTS BY PAYPAL You can pay using a credit card or with a Paypal account. All payments will be processed by Paypal and you will be covered by their comprehensive Buyer Protection. QUESTIONS If you have any questions please ask, I'm always happy to help.:-)

Buy W4209 12V 24V DC 220V AC Digital Temperature Controller Control Switch Thermostat with Normally Open for R145.50

Description:   Valve material: Brass Coil material: Copper Oil Seal material: NBR Size: 86 x 73 x 117mm Acting Motion: Direct Action Medium: air, water, oil,the neutral gas liquid Mode: Direct driven State: Normally closed Supply voltage: 12V DC Supply Current: 1.4 A Pipe size: G1 " Orifice size: 25mm Working pressure: Water,air: 0~1MPa Oil: 0~0.7MPa Fluid temperature: -5-80 ??/span> CV: 12 Installation: fluid direction should so the arrow points High quality spare part for use with pipelines in water, air and diesel applications.   Package Included:   1 x solenoid valve Detail Pictures:

SELECTED OPTION: SIZE: G1/2 CLICK HERE for more options in this item. Specifications: Material: ABS, Copper Color: White Type: G3/8", G1/2"  G3/8" Size: (L)X(H) 15x24.5cm /5.91"x9.65"(appr.) G1/2" Size: (L)X(H) 15x24.5cm /5.91"x9.65"(appr.)   Features: Made of ABS material, durable and not easy to rust. 3/8" and 1/2" connection side entry. Green environmental protection, durable, easy to installation. Simple above water float adjustment and quiet operation. Valve height and water level adjust for proper fit and most flush volume.   Note: Install the fill valve correctly, to ensure that the fill valve works normally: Step 1: Put the filling nozzle through the filling hole on tank side. Be sure that the float is not attached with tank side and the fill valve could not be askew. Then replace the plastic washer and lock nut and screw the lock nut tightly. Step 2: Connect the filling nozzle with water supply hose, screw the hose nut tightly. Then turn on the angle valve to check if water leaks from the connection of hose nut and filling nozzle. If leaks, release the water supply hose and connect again. Water level adjustment and fill valve maintenance: Adjust the float, to set up working water level, to get beat flush performance and save water at the same time. Clean the filter.   Package Included: 1 Pcs Toilet Valve Inlet Part

Buy LAIZE DN8 NPT 1/4 Brass Electric Solenoid Valve AC 220V/DC 12V/DC 24V Normally for R341.85

This item is sold brand new. It will be ordered from our supplier and normally ships in 15 to 20 working days Coolermaster Force 500 ATX Chassis with CM Elite ATX 12V Vw PSU CM Force 500 Features: - Classy and simplistic front panel design - USB 3.0 super speed port (internal) - Top mounted PSU slot for best PSU compatibility - Large tray cut-out for easy CPU cooler installation - Supports all High-End VGAs including the HD - Exposed 3.5 inch Slot for CardReaders - Tool-free system for ODDs, card reader and HDDs - VGA cooling vent with mm fan support - HDD cooling vent with 2x120mm fan support - Supports up to 6 fans in total (1 pre-installed) Specifications: - Available Color: Black - Materials: Steel body, plastic - Dimensions: 190 x 426 x mm - Net Weight: 5.23 kg - M/B Type: microATX, ATX - 5.25 inch Drive Bays: 2 (exposed) - 3.5 inch Drive Bays: 8 (1 exposed, 7 hidden) - 2.5 inch Drive Bays: 1 (hidden) - I/O Panel: USB 3.0 x 1 (int.), USB 2.0 x 2 - Mic x1, Audio x 1 (supports AC97/HD Audio) - Expansion Slots: 7 - Cooling System: Front: 140mm fan x 1 (optional), or 120mm fan x 2 (optional) - Rear: 120mm black fan x 1 (installed) - Side (left): mm fan x 1 (optional) - Side (right): 120mm fan x 2 (optional) - Power Supply Type: Standard ATX PS2/EPS 12V - Maximum Compatibility VGA card length: 320mm (with HDD cage) - CPU cooler height: mm