Diamond core

Ø20mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45¿¿ angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED ¿¿5.0mm 800 rpm ¿¿6.0mm 600 rpm ¿¿7.0mm 500 rpm ¿¿8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm   IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.  

Buy Diamond Core Drill Bit Hole Puncher For Air-conditioner Range Hood Dia. 20/30/40/51/63... (SIZE: #5) for R1,157.89

Buy DIAMOND CORE BIT 152MM X 450MM X 1 1/4 CONCRETE MASTER DBK for R5,709.58

Buy Diamond Core Bit 102Mm X 450Mm X 1 1/4 Concrete Master Dbk for R3,217.00

Ø10mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø12.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø16mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø10mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø8mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø38mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø19mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø14mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø30mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø6mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø20mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø10mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø40.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø5mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø22mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Adaptor - SDS Plus shank Adaptor length: 200mm Thread: M16 Connection type: SDS Plus Application: This is a SDS Plus adaptor to connect the Dry Cut Diamond Core Drill to your rotary hammer. Make sure the threads are the same as the Dry Cut Diamond Core Drill - M22 or M16. Take note that there are 2 connection types: Hex SDS Plus List of different adaptors: 1. Hex shank adaptors for the Dry Cut Diamond Core Drill range: Hex shank 70mm, M16 thread - TC18HEX1 Hex shank 200mm, M16 thread - TC18HEX2 Hex shank 300mm, M16 thread - TC18HEX3 Drift key for removing the pilot drill - TC18KEY Pilot drill bit (not included with adaptors)- TC18PILOT 2. SDS Plus adaptors for the Dry Cut Diamond Core Drill range: SDS Plus 70mm, M16 thread - TC18SDS1 SDS Plus 200mm, M16 thread - TC18SDS2 SDS Plus 300mm, M16 thread - TC18SDS3 SDS Plus 70mm, M22 thread - TC18SDS4 SDS Plus 200mm, M22 thread - TC18SDS5 SDS Plus 300mm, M22 thread - TC18SDS6 Drift key for removing the pilot drill - TC18KEY Pilot drill bit (not included with adaptors)- TC18PILOT NOTE: The pilot drill bit is not included with the adaptors and it is available separately - TC18PILOT INFORMATION: Use the drift key TC18KEY to remove or replace the pilot drill bit from the adaptors.

Adaptor - SDS Plus shank Adaptor length: 300mm Thread: M22 Connection type: SDS Plus Application: This is a SDS Plus adaptor to connect the Dry Cut Diamond Core Drill to your rotary hammer. Make sure the threads are the same as the Dry Cut Diamond Core Drill - M22 or M16. Take note that there are 2 connection types: Hex SDS Plus List of different adaptors: 1. Hex shank adaptors for the Dry Cut Diamond Core Drill range: Hex shank 70mm, M16 thread - TC18HEX1 Hex shank 200mm, M16 thread - TC18HEX2 Hex shank 300mm, M16 thread - TC18HEX3 Drift key for removing the pilot drill - TC18KEY Pilot drill bit (not included with adaptors)- TC18PILOT 2. SDS Plus adaptors for the Dry Cut Diamond Core Drill range: SDS Plus 70mm, M16 thread - TC18SDS1 SDS Plus 200mm, M16 thread - TC18SDS2 SDS Plus 300mm, M16 thread - TC18SDS3 SDS Plus 70mm, M22 thread - TC18SDS4 SDS Plus 200mm, M22 thread - TC18SDS5 SDS Plus 300mm, M22 thread - TC18SDS6 Drift key for removing the pilot drill - TC18KEY Pilot drill bit (not included with adaptors)- TC18PILOT NOTE: The pilot drill bit is not included with the adaptors and it is available separately - TC18PILOT INFORMATION: Use the drift key TC18KEY to remove or replace the pilot drill bit from the adaptors.

Adaptor - SDS Plus shank Adaptor length: 70mm Thread: M22 Connection type: SDS Plus Application: This is a SDS Plus adaptor to connect the Dry Cut Diamond Core Drill to your rotary hammer. Make sure the threads are the same as the Dry Cut Diamond Core Drill - M22 or M16. Take note that there are 2 connection types: Hex SDS Plus List of different adaptors: 1. Hex shank adaptors for the Dry Cut Diamond Core Drill range: Hex shank 70mm, M16 thread - TC18HEX1 Hex shank 200mm, M16 thread - TC18HEX2 Hex shank 300mm, M16 thread - TC18HEX3 Drift key for removing the pilot drill - TC18KEY Pilot drill bit (not included with adaptors)- TC18PILOT 2. SDS Plus adaptors for the Dry Cut Diamond Core Drill range: SDS Plus 70mm, M16 thread - TC18SDS1 SDS Plus 200mm, M16 thread - TC18SDS2 SDS Plus 300mm, M16 thread - TC18SDS3 SDS Plus 70mm, M22 thread - TC18SDS4 SDS Plus 200mm, M22 thread - TC18SDS5 SDS Plus 300mm, M22 thread - TC18SDS6 Drift key for removing the pilot drill - TC18KEY Pilot drill bit (not included with adaptors)- TC18PILOT NOTE: The pilot drill bit is not included with the adaptors and it is available separately - TC18PILOT INFORMATION: Use the drift key TC18KEY to remove or replace the pilot drill bit from the adaptors.

Time-saving positioning with quick centring bitQuick release coupling for core bitsSafety clutch with anti-lockup systemPrecise preselection and constant control of water flow rateWater-saving precision meteringUltra-efficient dust extraction in dry operating modeWet and dry drilling without any adaptationsAuxiliary handle on trigger grip for powerful, back-saving drillingUniversal diamond core bits for wet and dry useDIA 150 W applicationsHand-held drilling into brickwork, even in confined spaces or up a ladderDrilling into concrete, granite, etc.,hand-held or mounted on a drill standDIA 150 W featuresTime-saving positioning with quick centring bitQuick release coupling for core bitsSafety clutch with anti-lockup systemPrecise preselection and constant control of water flow rateWater-saving precision meteringUltra-efficient dust extraction in dry operating modeWet and dry drilling without any adaptationsAuxiliary handle on trigger grip for powerful, back-saving drillingUniversal diamond core bits for wet and dry useRapid changeover from hand-held to stand mounted drillingInfinitely variable speed adjustmentElectronic overload protection and soft startElectronic constant speed control Specifications:DIA 150 W Rated power · · · · · · · · · · · · · · · 1800 watts Drilling range: Hand-held, wet drilling· · · · · · · dia. 52-162 mm Hand-held, dry drilling · · · · · · · dia. 52-212 mm Stand mounted, wet drilling· · · dia. 52-162 mm Sewer pipe, hand-held, wet drilling up to dia. 200 mm Rated speed· · · · · · · · · · · · · · · · 480-630 rpm Machine weight · · · · · · · · · · · · · 6.1 kg Chuck· · · · · · · · · · · · · · · · · · · · · G 1/2" Standard contents:DUSS diamond core drill with PRCD circuit breakerSide handleAuxiliary handleCentring rodOpen-ended wrenches (22 and 30 mm)Teflon sprayCarrying case

Dry Cut Diamond Core Drill For plumbers, electricians or general contractors needing to drill a hole quickly and cleanly in brickwork for an installation. Core diameter: Ø65mm Depth: 170mm Adaptor thread: M16 Main use: Brickwork Application: The dry cut diamond core drill is designed to be used without water to drill into: Brickwork Roof tiles Slate Stone Paving It allows the user to drill neat and clean holes quickly without the setup an cleanup time associated with using a water-cooled drilling jig. INFORMATION: Have a look at the different adaptors under the EXTRA INFO tab and the complete range under the ACCESSORIES tab. IMPORTANT: Not for reinforced drilling! Use a wall scanner to detect reinforcing, water pipes or electrical conduit.

Dry Cut Diamond Core Drill For plumbers, electricians or general contractors needing to drill a hole quickly and cleanly in brickwork for an installation. Core diameter: Ø117mm Depth: 170mm Adaptor thread: M16 Main use: Brickwork Application: The dry cut diamond core drill is designed to be used without water to drill into: Brickwork Roof tiles Slate Stone Paving It allows the user to drill neat and clean holes quickly without the setup an cleanup time associated with using a water-cooled drilling jig. INFORMATION: Have a look at the different adaptors under the EXTRA INFO tab and the complete range under the ACCESSORIES tab. IMPORTANT: Not for reinforced drilling! Use a wall scanner to detect reinforcing, water pipes or electrical conduit.

Dry Cut Diamond Core Drill Set Core drills in the set: Ø38mm Ø52mm Ø65mm Ø117mm The set also includes: (x1) drift key (x1) Pilot drill bit (x1) 70mm Hex adaptor (x1) 70mm SDS Plus adaptor (x1) 200mm Hex adaptor (x1) 200mm SDS Plus adaptor Application: The dry cut diamond core drill is designed to be used without water to drill into: Concrete Concrete pipes Brickwork Roof tiles Slate Stone Paving Tarmac It allows the user to drill neat and clean holes quickly without the setup an cleanup time associated with using a water-cooled drilling jig. For plumbers, electricians or general contractors needing to drill a hole quickly and cleanly in concrete for an installation. IMPORTANT: Not for reinforced drilling! Use a wall scanner to detect reinforcing, water pipes or electrical conduit.

Dry Cut Diamond Core Drill For plumbers, electricians or general contractors needing to drill a hole quickly and cleanly in concrete for an installation. Core diameter: Ø52mm Depth: 170mm Adaptor thread: M22 Main use: Concrete Application: The dry cut diamond core drill is designed to be used without water to drill into: Concrete Concrete pipes Brickwork Roof tiles Slate Stone Paving Tarmac It allows the user to drill neat and clean holes quickly without the setup an cleanup time associated with using a water-cooled drilling jig. INFORMATION: Have a look at the different adaptors under the EXTRA INFO tab and the complete range under the ACCESSORIES tab. IMPORTANT: Not for reinforced drilling! Use a wall scanner to detect reinforcing, water pipes or electrical conduit.

Dry Cut Diamond Core Drill For plumbers, electricians or general contractors needing to drill a hole quickly and cleanly in concrete for an installation. Core diameter: Ø38mm Depth: 170mm Adaptor thread: M22 Main use: Concrete Application: The dry cut diamond core drill is designed to be used without water to drill into: Concrete Concrete pipes Brickwork Roof tiles Slate Stone Paving Tarmac It allows the user to drill neat and clean holes quickly without the setup an cleanup time associated with using a water-cooled drilling jig. INFORMATION: Have a look at the different adaptors under the EXTRA INFO tab and the complete range under the ACCESSORIES tab. IMPORTANT: Not for reinforced drilling! Use a wall scanner to detect reinforcing, water pipes or electrical conduit.

Dry Cut Diamond Core Drill For plumbers, electricians or general contractors needing to drill a hole quickly and cleanly in brickwork for an installation. Core diameter: Ø52mm Depth: 170mm Adaptor thread: M16 Main use: Brickwork Application: The dry cut diamond core drill is designed to be used without water to drill into: Brickwork Roof tiles Slate Stone Paving It allows the user to drill neat and clean holes quickly without the setup an cleanup time associated with using a water-cooled drilling jig. INFORMATION: Have a look at the different adaptors under the EXTRA INFO tab and the complete range under the ACCESSORIES tab. IMPORTANT: Not for reinforced drilling! Use a wall scanner to detect reinforcing, water pipes or electrical conduit.

Description: Segment height: 10mm Bit length: 16" overall length w/ 13.5" depth of cut Thread size: 1-1/4" — 7 threads. Application: Intended for drilling hard concrete, block, brick, masonry, and the like materials ● Notice: Drilling method: use WET only ● Excellent choice for all type of general drilling ● Ideal for plumbers, electricians or general contractors Package Included: 4 x Wet Diamond Core Drill Bit (2" 3" 4" 5") More Details:

Buy Tork Craft Diamond Core Bit 64mm For Tiles Hex Shank for R360.53

Buy Tork Craft Diamond Core Bit 52 X 170mm Universal Purpose M22 for R1,239.70