Bit prototyping breakout board

Buy MICRO:BIT PROTOTYPING BREAKOUT BOARD V1+BREADBOARD KS0292 for R188.73

Buy PROTOTYPING BREAKOUT BOARD V2 + BREADBOARD KS0307 for R245.37

Description SparkFun Micro:Bit Breakout The SparkFun Micro:Bit Breakout is a board that connects to the Micro:Bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and SPI buses. This breakout board for the Micro:Bit’s edge connector allows intermediate and advanced users to connect the Micro:Bit to breadboards and other sensors, motors, LEDs and more! The Micro:Bit on its own has three digital/analog input/output rings available for you to use initially with alligator clips. With the Micro:Bit breakout we have broken out all 21 GPIO pins, power and ground to a pre-soldered 0.1" header. With this breakout you will be able to unlock the full potential of your Micro:Bit Note: There is no Micro:Bit included with this breakout; it will need to be purchased separately. Resources Product Page Schematic Hookup Guide Micro:Bit Guide GitHb Shipping List 1 X SparkFun Micro:Bit Breakout More Products View More Products

Description: For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1115 provides 16-bit precision at 860 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differential channels. As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the full range. We like this ADC because it can run from 2V to 5V power/logic, can measure a large range of signals and its super easy to use. It is a great general purpose 16 bit converter. The chip's fairly small so it comes on a breakout board with ferrites to keep the AVDD and AGND quiet. Interfacing is done via I2C. The address can be changed to one of four options (see the datasheet table 5) so you can have up to 4 ADS1115's connected on a single 2-wire I2C bus for 16 single ended inputs. Feature: Wide supply range: 2.0V to 5.5V Low current consumption: Continuous Mode: Only 150uA Single-Shot Mode: Auto Shut-Down Programmable data rate: 8SPS to 860SPS Internal Low-drift voltage reference Internal oscillator Internal PGA I2C interface: Pin-Selectable Addresses Four Single-ended or two differential inputs Programmable comparator This board/chip uses I2C 7-bit addresses between 0x48-0x4B, selectable with jumpers Package included: 3 x I2C ADS1115 16 Bit ADC 4 Channel Module

Description:   For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1115 provides 16-bit precision at 860 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differential channels. As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the full range. We like this ADC because it can run from 2V to 5V power/logic, can measure a large range of signals and its super easy to use. It is a great general purpose 16 bit converter. The chip's fairly small so it comes on a breakout board with ferrites to keep the AVDD and AGND quiet. Interfacing is done via I2C. The address can be changed to one of four options (see the datasheet table 5) so you can have up to 4 ADS1115's connected on a single 2-wire I2C bus for 16 single ended inputs.   Feature:   Wide supply range: 2.0V to 5.5V Low current consumption: Continuous Mode: Only 150uA Single-Shot Mode: Auto Shut-Down Programmable data rate: 8SPS to 860SPS Internal Low-drift voltage reference Internal oscillator Internal PGA I2C interface: Pin-Selectable Addresses Four Single-ended or two differential inputs Programmable comparator This board/chip uses I2C 7-bit addresses between 0x48-0x4B, selectable with jumpers Package included: 10 x I2C ADS1115 16 Bit ADC 4 Channel Module

Buy IOBIT Expansion Board Breakout Adapter Board For BBC Micro: bit Development Module Contains Buzzer for R334.00

Buy IOBIT Expansion Board Breakout Adapter Board For BBC Micro: bit Development Mo for R309.99

Description: For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1015 provides 12-bit precision at 3300 samples/second over I 2 C. The chip can be configured as 4 single-ended input channels, or two differential channels. As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the full range. We like this ADC because it can run from 2V to 5V power/logic, can measure a large range of signals and its super easy to use. It is a great general purpose 12 bit converter. The chip's fairly small so it comes on a breakout board with ferrites to keep the AVDD and AGND quiet. Interfacing is done via I 2 C. The address can be changed to one of four options (see the datasheet table 5) so you can have up to 4 ADS1015's connected on a single 2-wire I 2 C bus for 16 single ended inputs. Package included: 5 x Analog-to-Digital Converter  

Description: For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1015 provides 12-bit precision at 3300 samples/second over I 2 C. The chip can be configured as 4 single-ended input channels, or two differential channels. As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the full range. We like this ADC because it can run from 2V to 5V power/logic, can measure a large range of signals and its super easy to use. It is a great general purpose 12 bit converter. The chip's fairly small so it comes on a breakout board with ferrites to keep the AVDD and AGND quiet. Interfacing is done via I 2 C. The address can be changed to one of four options (see the datasheet table 5) so you can have up to 4 ADS1015's connected on a single 2-wire I 2 C bus for 16 single ended inputs. Package included: 1 x Analog-to-Digital Converter