5pcs module 30a

Buy 5pcs ACS712 Module 30A Current Detection Board ACS712 Hall Current Sensor Module for R321.42

Buy 5Pcs BESTEP 1 Channel 24V Relay Module 30A With Optocoupler Isolation Support High And Low Level Tri for R366.00

Buy 3pcs ACS712 Module 30A Current Detection Board ACS712 Hall Current Sensor Module for R286.00

Buy 10pcs BESTEP 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support H for R757.91

5Pcs 30A New Range Current Sensor Module Board For ACS712 Descrition: The current sensor chips: ACS712ELC-30A The module can measure the positive and negative 30 amps, corresponding to the analog output 66mV / A Pin 5V power supply, on-board power indicator Using gold plated circuit boards No test current through the output voltage is VCC / 2 Size: 31 x 13mm Note: ACS712 is based on the principle of the Hall test, please use this field to avoid impact Package included: 5 x 30A - ACS712 module

5pcs 1CH 12V 30A Relay Module High Power Relay Control Board Single Switch

5Pcs HC-12 433 SI4463 Wireless Serial Module Remote 1000M With Antenna Note: HC-11 cannot communicate with the HC-12, they work independently, in pairs Features: Supply voltage: 3.2V~5.5V. (If the module you want to work long hours in the emission state, it is recommended that when the supply voltage exceeds 4.5V threaded a 1N4007 diode to prevent module built-in LDO heated) Default address range (open field test): About 600m (maximum communication distance adjustable reach 1000m, the baud rate is 5000bps) Default idle current: 16MA (In different working modes operating current is different) Module dimensions: 27.8 x 14.4 x 4mm Operating frequency range: 433.4-473.0MHz, up to 100 channels of communication The maximum transmit power: 100mW (settable) Module support software upgrade Default factory settings: Mode FU3, baud rate is 9600bps, communication channels CH001 (433.4M) Package included: 5 x HC-12 433 Serial module AT command set:   Module parameters, AT command set AT command is used to set the parameters of the function module and switching modules need to exit the setting mode after setting to take effect. Meanwhile, modify the parameters and functions, power-down is not lost.   Enter the command mode: The first entry mode - normal use (has the power) in the first 5-pin "SET" is set low; The second mode of entry - power, 5th pin "SET" again first set low on power. Both methods can make the module into AT command mode, release ("SET" pin is not connected low) to exit command mode. After the exit command mode, if you change the module function, the function will be cut to the appropriate state. The second way is fixed in serial format 9600, N, 1 into the AT.   Instructions: 1. AT Test instructions Example: Send module commands "AT", the module returns "OK".   2. AT + Bxxxx Change the serial port baud rate command. You can set the baud rate is 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps. The factory default is 9600bps. Example: Set the module serial port baud rate is 19200bps, please send module command "AT + B19200", the module returns "OK + B19200".   3. AT + Cxxx Change the wireless communication channel, selectable from 001 to 127 (more than 100 radio channels after the communication distance not guaranteed). The default value is 001 radio channels, operating frequency is 433.4MHz. Step channel is 400KHz, the operating frequency of the channel 100 is 473.0 MHz.   Example: Set module to channel 21, please send module command "AT + C021", the module returns "OK + C021". After exiting the command mode, the module in the first 21 channels, operating frequency is 441.4 MHz. Note: Because the wireless receiver module sensitivity HC-12 is relatively high, the baud rate is greater than when air 58000 bps, 5 must be shifted to the adjacent channel use. When the air baud rate is not greater than 58000 bps, if the short distance (10 meters) communication, but also need to stagger five adjacent channel use.   4. AT + FUx Change the module serial pass-through mode, there FU1, FU2 and FU3 three modes. Module default mode is FU3, two serial pass-through mode module must be set to the same communication. See detailed above, "wireless serial pass-through" part. Example: Send module commands "AT + FU1", the module returns "AT + OK".   5. AT + Px The default setting is 8, maximum transmit power, communication distances. Transmit power level is set to 1, the minimum transmission power. In general, the transmission power of each drop 6dB, communication distance will be reduced by half. Example: Send module commands "AT + P 5", the module returns "OK + P5". After exiting the command mode, the module transmit power is +11 dBm. Package included: 1 x HC-12 module

5pcs HC-05 Wireless Bluetooth Serial Module With Baseplate For Arduino Note: This module does not suitable for IOS system. Pin serial port descriptions: PIO8 connect LED, indicates the status of working, after powered the module flashing, different states in different flashing intervals. PIO9 connect LED, indicates successful connecting module, after successful mating bluetooth serial port, LED long lights. PIO11 state switch pin (high level) -> AT command response to the work state, low level or dangling -> Bluetooth regular work status. On module with a reset circuit, re-power to complete the reset. Main module setup steps: 1. PIO11 set high. 2. Power ON, the module into the AT command response status. 3. HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity, no flow control. 4. Serial send characters "AT + ROLE = 1 r n", successful return "OK r n", which r n for carriage return. 5. PIO set low, re-power, module as the main module, automatic search from module to establish a connection. Feature: 6V - 4.5V power supply; Support connect Android phones with Bluetooth; The default baud rate: 9600 can be modified according to the data sheet; Package included: 5 x HC-05 Wireless Bluetooth Serial Module

5Pcs MAX7219 Dot Matrix Module MCU LED Control Module Kit For Arduino Specifications: A single module can drive an 8 x 8 common cathode lattice Operating voltage: 5V Size: 5 x 3.2 x 1.5 cm (L x W x H) LED color: Red With four screws hole, aperture 3mm With input and output interfaces, supports multiple modules cascade Wiring instructions: 1. The module left side as an input port and the output port on the right 2. To control a single module, just connect the input port to the CPU 3. When cascading multiple modules, the input port of the first module connect to the CPU, the output port connect to the input port of the second one, and so on. In the case of 51 MCU: VCC → 5V GND → GND DIN → P22 CS → P21 CLK → P20 Note: 1. VCC and GND is not reversed, it would burn the chip! 2. When the 51 microcontroller P0 port controlling, must be connected to the pull-up resistor, it is recommended that the resistance of 4.7K--10K 3. Please install lattice into the round hole first, and then insert the round hole to PCB board and weld. Face the side of lattice with words, from left to right pin order is 123456. PCB board 1st pin is square pad! 4. Electrolytic capacitors long-pin as positive, short-pin as negative; ceramic capacitor hsa no positive and negative points Package included: 5 x LED module 5 x Dupont line (5P-20cm)

5Pcs Socket Adapter Module Board For 8 Pin NRF24L01+ Wireless Transceiver Module Specification: Voltage: 3.3V It's for 8 Pin NRF24L01+ Module A simple socket board which is for NRF24L01 wireless module On-board AMS1117-3.3 chip It can be used with NRF24L01 wireless module Dimension: 26 x 19 x 12mm Note: Wireless module operating voltage is generally 3.3V, while the ordinary 51 microcontroller 5V, this module is wireless module with 51 single system board used in conjunction. Data Link: https://pan.baidu.com/s/1o6ug0yu Package included: 5 x Wireless Socket Adapter Module Board

5Pcs Soil Hygrometer Humidity Detection Moisture Sensor For Arduino Description: This is a summary of the soil moisture sensor can be used to detect moisture, when the soil is dry, the module outputs a high level, whereas output low. Using this sensor make an automatic watering system, so that your garden plants without people to manage. Operating voltage: 3.3V~5V. Adjustable sensitivity (shown in blue digital potentiometer adjustment) Dual output mode,analog output more accurate. A fixed bolt hole for easy installation. With power indicator (red) and digital switching output indicator (green). Having LM393 comparator chip, stable. Panel PCB Dimension: 3cm x 1.5cm. Soil Probe Dimension: 6cm x 2cm. Cable Length: 21cm. VCC: 3.3V-5V. GND: GND. DO: digital output interface(0 and 1). AO: analog output interface. Instructions for Use: 1. Soil moisture module is most sensitive to the ambient humidity is generally used to detect the moisture content of the soil. 2. Module to reach the threshold value is set in the soil moisture, DO port output high, when the the soil humidity exceeds a set threshold value, the module D0 output low. 3. The digital output D0 can be connected directly with the microcontroller to detect high and low by the microcontroller to detect soil moisture. 4. The digital outputs DO shop relay module can directly drive the buzzer module, which can form a soil moisture alarm equipment. 5. Analog output AO and AD module connected through the AD converter, you can get more precise values of soil moisture. Package Included: 5 x Soil moisture detector module 5 x Probe 5 x 2P Jumper Cable

5Pcs Jog Type Touch Sensor Module For Arduino Description: This is jog type capacitive touch switch sensor module based on a touch detection IC TTP223B. Normally, the output is low level(at mode of low power consumption). When the finger touch the corresponding location, output will be high(at quick speed mode). When the module do not be touched for 12 seconds, the mode would switch to low-power mode. It can be installed in the module, such as plastic, glass, non-metallic material surface. But not cover thin sheets(metal) on the surface of the module. Just touch the correct position, it can be hidden in walls, desktops and other parts to be buttons. Allows you to remove the troubles of conventional push-type buttons. Feature: Low power consumption Can replace the traditional key With four M2 screw holes, easy for operation Specification: Operating voltage: DC 2.0V ~ 5.5V VOH: VCC 0.8V VOL: VCC 0.3V Sink current: 8mA @ VCC = 3V, VOL = 0.6V Source current: -4mA @ VCC = 3V, VOH = 2.4V Response time: 220ms (at mode of low power consumption) and 60ms (at quick speed mode) Size: 24 x 24 x 7.2mm Package included: 5 x Capacitive jpg type touch sensor module

5Pcs 5V 1-Channel H/L Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load: AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 5 x 1 Channel H/L trigger optocoupler relay module

5Pcs 5V To 3.3V DC-DC AMS1117 800MA Step-Down Power Supply Buck Module Features: Size: 8.6 x 12.33 mm Input voltage: DC 4.2 V - 10 V Output: 3.3 V, 800 mA Note: 1.Boost modules or buck module indicate the operating voltage, Please do not exceed operating voltage, or it will be damaged easily! 2.Boost module output voltage can only be greater than or equal to input voltage, cannot be less than the input voltage! 3.Buck module input voltage must be higher than output voltage of 1.5V or 2V, otherwise it can not output enough power! 4.Automatic Adjustable Boost or Buck module has start voltage and limit working voltage, Please do not exceed them, or it will be damaged easily! 5.Cannot reverse polarity, or it will be short circuit, or will be born easily! Package included: 5 x Step-down module

5Pcs 5V Infrared Line Tracking Sensor Module For Arduino Feature: Quantity: 5pcs Size: 3.5 x 1cm Power supply: 5V DC Detector distance: 10mm Build-in Tcrt5000 Sensor NSOR Applicable to a variety of platforms including Arduino / AVR / ARM /PIC Package included: 5 x Tracking Sensor Module