10pcs trigger driver

Buy 10pcs A4988 Driver Module Stepper Motor Driver Board with Heatsink... for R299.00

Buy 10pcs A4988 Driver Module Stepper Motor Driver Board with Heatsink for R351.35

Feature: This cable generally use for LED screen, is very convenience to use. Suitable for any 30 pin, 2 channel, 6 bit interface. Package includes: 10 x 30Pin Cable

Feature: This cable generally use for LED screen, is very convenience to use. Suitable for any 30 pin, 1 channel, 6 bit interface. Package included: 10 x 30Pin Cable

10Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load:  AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 10 x 1 Channel H/L level trigger optocoupler relay module  

10Pcs DC 5V 4 Phase 5 Wire Stepper Motor With ULN2003 Driver Board Description: This is 28YBJ-48 DC 5V 4 phase 5 wire stepper motor with ULN2003 driver board 5-wire phase can drive ordinary uln2003 chip can also be connected as phase 2 may be supporting the development board, direct plug, easy to use stepper motor used in the development board Motor: Diameter: 28mm Voltage: 5V Step angle: 5.625 x 1/64 Reduction ratio: 1/64 ULN2003 driver board: A, B, C, D LED indication Four-phase stepper motor work status Size: 31mm x 35mm Package included: 10 x ULN2003 driver board 10 x 28BYJ-48 stepper motor

10pcs DC 7V To 30V 150mA To 750mA A3967 Easy Driver Stepper Motor Driver Board For Arduino

10Pcs CJMCU 1 Bit WS2812 5050 RGB LED Driver Development Board Feature: Votalge: DC 5V Color: RGB Package included: 10 x 1 Bit WS2812 5050 RGB LED Driver Development Board

10Pcs CJMCU 4 Bit WS2812 5050 RGB LED Driver Development Board Feature: Votalge: DC 5V Color: RGB Size: 15MM X 15MM Pacakge included: 10 x 4 Bit WS2812 5050 RGB LED Driver Development Board

10Pcs CJMCU 7 Bit WS2812 5050 RGB LED Driver Development Board Feature: Radius 11.5mm Package included: 10 x CJMCU 7 Bit WS2812 5050 RGB LED Driver Development Board.

10Pcs CJMCU 8 Bit WS2812 5050 RGB LED Driver Development Board Feature: Votalge: DC 5V Color: RGB Package included: 10 x CJMCU 8 Bit WS2812 Development Board

10pcs BESTEP 1 Channel 5v Relay Module High And Low Level Trigger For Arduino Package contains 1 X item of the smallest listed variant.

10Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 10 x Micro SD TF card module

Feature: Working voltage: DC5V-36V Trigger signal source: digital high level (DC3.3V-20V), can be connected to the microcontroller IO port, PLC interface, DC power supply, etc., can connect PWM signal, support signal frequency 0-20khz Output: DC5V-36V, continuous current at room temperature 15A, power 400W, assisted cooling conditions, the maximum current up to 30A. Applications: Output can control high power equipment, motors, light bulbs, LED lights, DC motors, mini pumps, solenoid valves, etc., you can enter the PWM, control the motor speed, lamp brightness and so on. Operating temperature: -40 to 85 ° C Size: 3.4 x 1.7 x 1.2cm Package includes: 10 x MOS Trigger Switch Driver Module

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: 5V Omron solid state relays 240V / 2A, output with resistive fuse 240V / 2A. Dimensions: 25x34x25 (length x width x height) Input Power: 5VDC Control signal input voltage: (0-2.5V low state relay ON) (3-5V state high relay OFF) Feature: Voltage:5V Quiescent current: 0 mA Operating current: 12.5mA Trigger Voltage: 3.3-5V Trigger current: 2mA DC +: positive power supply (according to the relay voltage supply) DC-: negative power supply CH1: relay module signal triggering end (low to trigger active) Package included: 10 x One way Solid State Relay Module For Arduino 10Pcs One way Solid State Relay Module For Arduino 10Pcs One way Solid State Relay Module For Arduino 10Pcs One way Solid State Relay Module For Arduino