10pcs power
Top sales list 10pcs power
South Africa (All cities)
10Pcs NRF24L01+ SI24R1 2.4G Wireless Power Enhanced Communication Receiver Module 10Pcs NRF24L01 SI24R1 2.4G Wireless Power Enhanced Communication Receiver Module Description:NRF24L01 SI24R1 is fully compatible (SPI operation timing, registers, definitions, state diagram), can communicate with each other, support NRF24L01 all communications. Default mode output power of SI24R1 is 2 ~ 3dBm, if you want the output is 7dBm, you should write 1 (NRF24L01 This bit is not used, the default is 0) into the lowest bit register address 0x06 (RF_SETUP). For example, the 01register, 0x061111.Pacakge included:10 x Wireless Power Enhanced Communication Receiver Module
R 330
See product
South Africa (All cities)
10Pcs 3A XL6009 DC-DC 50KHz Adjustable Step-up Power Converter Module Specification: Wide Input voltage: 3V-30V Output Voltage: 4-35V (Adjustable) Output current: rated current 3A MAX (Heat-sink Needed) If you need its output power greater than 15W, please add with heat-sink Conversion efficiency: Up to 92% (output voltage higher, the higher the efficiency) Switching Frequency: 50KHz Rectifier: Non-Synchronous Rectification Short circuit protection: current limiting, since the recovery Operating temperature: Industrial grade (-40 to +85) (output power 10W or less) Full load temperature rise: 40 Load regulation: 0.5% Voltage regulation: 0.5% Size:47 x 26 x 15 mm Package included: 10 x XL6009 DC-DC 50KHz Adjustable Step-up Power Converter Module
R 480
See product
South Africa
10Pcs MB102 Breadboard Module Adapter Shield 3.3V/5V For Arduino Board Description: Breadboard power supply module, compatible with 5 V, 3.3 V Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: Fluctuation two road independent control, can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient external lead use. Size: 5.3*3.2*2.5cm Weight: 12g Please notice: this item only a Power Supply Module, Breadboard is not included. Package included: 10 x Power supply module Breadboard power supply module, compatible with 5 V, 3.3 V.
R 229
See product
South Africa (All cities)
10Pcs 5V 700mA 3.5W AC-DC Step Down Isolated Switching Power Supply Module Feature: Input voltage: AC 85 ~ 265v 50 / 60HZ or DC100v-370v Output voltage: DC5V (± 0.2V) Output Current: 700mA Power: 3.5W Package included: 10 x 5V 700mA 3.5W AC-DC Step Down Isolated Switching Power Supply Module
R 330
See product
South Africa (All cities)
10Pcs DC-DC 12V to 3.3V/5V/12V Voltage Converter Power Supply Module Feature:One channel input: DC 6V - 12V (the input voltage must be higher than the output voltage to 1V or more.)Triple output: 3.3V (ﾱ 0.05v error), 5V (ﾱ 0.05v error), 800mA (load current can not exceed 800ma), 12V (12V input directly to the output)Specially designed two rows of needle fixing hole, can be directly fixing on the plate to extend the experiment;Using multiple input and output pin, easy to use and connect;PCB board size: 4.5 x 4.5cmWith power indicator (red)Package includes:10 x Multi-output Power Supply Module
R 310
See product
South Africa (All cities)
10pcs AC-DC 12V 0.5A 6W Switching Power Bare Board For LED Stage Light AC 100-240V To DC 12V Description: 1. Input voltage: AC 100V-240V 50-60Hz2. Output voltage: DC 12V3. Output current: 500ma4. Output power: 6W5. Size: 5.5 x 3.5 x 1.9cmPackage included:10 x AC-DC 12V 500ma 6W switching power module
R 460
See product
South Africa (All cities)
10Pcs 3W LED Module High Power Module For Arduino Feature: Color temperature: Warm White 3000-3200K / white 6000-6500K Forward current: 700MA Luminous flux: White 180-200LM (lumens), Red 90-100LM (lumens), Green 80-90LM (lumens) Forward voltage: 3.3 - 3.6 V Reverse voltage: 5V Power: 3W Viewing angle: 180° Working temperature: -20° to 60° Storage temperature: 20° to 60° Package included: 10 x LED module
R 297
See product
South Africa (All cities)
10Pcs 9V Battery Box Pack Holder With ON/OFF Power Switch Toggle Black Feature: Easy to remove cover and install battery Cover slides with screw Have OFF / ON switch Specification: Material: plastic Color: black Cable length: about 14.5cm Fitment: Fit for 9V batteries Package included: 10 x 9V battery holder with power switch
R 171
See product
South Africa
10Pcs 5V 16M ATmega328P Arduino Compatible Version LilyPad 328 Main Board Description: The Arduino Compatible LilyPad is a microcontroller board designed for wearables and e-textiles. It can be sewn to fabric and similarly mounted power supplies, sensors and actuators with conductive thread. The board is based on the ATmega328 with the Arduino bootloader. The main board has a minimum number of external components to keep it as small (and as simple) as possible. The latest version supports automatic reset for even easier programming. The back side of the LilyPad is completely flat. It uses a surface mount programming connector, which keep the header from poking through. Specification: Microcontroller: ATmega328P Operating voltage: 2.7V ~ 5.5V (recommended 5V) Input voltage: 2.7V ~ 5.5V (recommended 5V) Digital I/O pins: 14 (of which 6 provide PWM output) Analog input pins: 6 DC current per I/O pin: 40mA Flash memory: 16KB (of which 2KB used by bootloader) SRAM: 1KB EEPROM: 512bytes Clock speed: 16MHz Note: Don't power the LilyPad Arduino with more than 5.5V, or plug the power in backwards: you'll kill it. Package included: 10 x Arduino compatible LilyPad ATmega328P
R 632
See product
South Africa (All cities)
10Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load: AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 10 x 1 Channel H/L level trigger optocoupler relay module
R 346
See product
South Africa (All cities)
10pcs DC-DC 9V 3A Power Supply Module Buck Step Down Regulator Module 24V 18V 12V To 9V Fixed Output Package contains 1 X item of the smallest listed variant.
R 430
See product
South Africa (All cities)
10Pcs 3A XL6009 DC-DC 50KHz Adjustable Step Up Power Converter Module Package contains 1 X item of the smallest listed variant.
R 630
See product
South Africa
10Pcs 1100 Meter Long Distance NRF24L01+PA+LNA Wireless Module Board With Antenna Desription: NRF24L01P + PA + LNA Division for the ultra-long-distance data transmission, specially developed high-power and high sensitivity wireless module 2.4G ISM band NRF24L01P + PA + LNA wireless module to work in the license-free that can be point-to-point applications or be composed of a star network. Digital transmission chip NRF24L01+ with the Division of Professional Design professional full two-way RF power amplifier high power PA and LNA chip, RF switches and band pass filters, makes effective communication distance greatly expand. RF part, it has been done a lot of optimization matching debugging. The emission efficiency to achieve the highest harmonic minimum and make NRF24L01P + PA + LNA wireless module of RF interference to the external equipment reaches minimum, while not susceptible to interference from other devices. NRF24L01P + PA + LNA wireless module integration is extremely high, the size is 41mm x 15.5mm to make conveniently embedded. Package included: 10 x 1100 Meter Long Distance NRF24L01+PA+LNA Wireless Module Board With Antenna
R 771
See product
South Africa
10Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 10 x Micro SD TF card module
See product
South Africa (All cities)
10Pcs Speed Measuring Sensor Counter Motor Test Groove Coupler Module For Arduino Application: Widely used in motor speed detection, pulse count, the position limit, etc. Feature: Using imported groove optical coupling sensor, width 5mm. It have the output state light, if output high level, the lights are off. if output low level,it on. If it covered,it will output high level;otherwise it output low level. Good signal and waveform, with strong driving ability for more than 15mA. The working voltage of 3.3V to 5V. Output: digital switch output (0 and 1). Equipped with a fixed bolt hole, easily install. Small board PCB size: 3.2 cm x 1.4 cm. Use the LM393 wide voltage comparer. Specification: The DO output interface can be directly connected to a micro-controller IO port, if there is a block detection sensor, such as the speed of the motor encoder can detect. DO modules can be connected to the relay, limit switch, and other functions, it can also with the active buzzer module, compose alarm. Wiring specification: VCC Connect the positive 3.3 5 v power supply GND Connect power negative DO TTL switch signal output AO This module does not work Package included: 10 x Speed Measuring Sensor Module
R 205
See product
South Africa (All cities)
10pcs Blue 0.36 Inch DC 0-30V 3 Wire LED Volt Meterr Digital Display Panel Volt Meterr Feature: The black line connected to the public negative electrode, red line connected to positive pole of power supply, yellow line connected to positive pole of tested power supplyMaterial: Plastic ShellDisplay Digit: 3Measuring Range: DC 0-30VWorking voltage: 4-30VDisplay Size: Approx 2.3cm x 1.2cm / 0.91' x 0.47'Overall Dimension: Approx 3.4cm x 2.2cm x 2cm / 1.34' x 0.87' x 0.79' (L x W x H)Cable Length: Approx 20cm / 7.87' Package Included: 10 x Blue Digital LED Display Voltmeter
R 670
See product
South Africa (All cities)
10Pcs XH-M400 Step Down Module Adjustable XL4016E1 High Power DC-DC 8A DC4-40V With Regulator
R 960
See product
South Africa (All cities)
10pcs LED Corridor Light Intelligent Sound And Light Control Power Supply Module Package contains 1 X item of the smallest listed variant.
R 390
See product
South Africa
10Pcs 50mm High Temperature Polyimide Film Heat Resistant Tape Feature: Size: 50mm Longth: About 28m Color: AMBER Thickness: 0.055mm Elongation: 50% Tensile strength: ≥ 42N/25mm Peel strength: ≥ 26N/25mm Tack: 24# Adhesive strength: 48H (Note: the data is the General test values, for reference only) Product Performance: The color is brown (amber), Goldfinger tape sticky is good, obedient, high temperature, solvent, no seepage tin and no adhesive residue Products with excellent electrical performance: Short-term temperature 300 ?? long-term temperature 250 ?? High insulation, high temperature, low temperature, acid, low electrolysis, good mechanical properties, abrasion and tear; Special agent treatment, adhesion strength, after tear the surface without leaving any remnants. The main uses: Mainly used for paint, sealing, footwear, packaging fixed, construction and decoration industries; Widely used as the electronics industry in transformers, motors, coils, capacitors and variable frequency power supply and other high-temperature insulation wound; Suitable for printed circuit board (PCB), SMT tin stoves, wave soldering process masking Goldfinger; High-grade electrical insulating protection and fixed lithium battery positive and negative effects; Suitable for solder protection; Cell phone lithium battery manufacturing strapping. Package included: 10 x High Temperature Tape (50mm)
R 1.945
See product
South Africa
10Pcs Orinigal M27C322-100F1 DIP-42 Mbit 32M EPROMs EPROM Feature: Suitable for microprocessor systems requiring large data or program storage. It is organised as 2 M Words of 16 bit. The pin-out is compatible with a 32 Mbit Mask ROM. The FDIP42W has a transparent lid which allows the user to expose the chip to ultraviolet light to erase the bit pattern. A new pattern can then be written rapidly to the device by following the programming procedure. For applications where the content is programmed only one time and erasure is not required. Specification: Power supply voltage: 5V ± 10% Programming voltage: 12V ± 0.25V Programming practice: 50μs / word Operation access time: 80ns Word width can be configured to 32 mbit mask rom replacement Stand-by current: 100μA Active current: 50mA at 5MHz Package includes: 10 x M27C322-100F1 DIP-42 Mbit EPROM
R 230
See product
South Africa (All cities)
10Pcs ATTINY85 Mini Usb MCU Development Board For Arduino Feature: 8K Byte of In-System Programmable Program Memory Flash 512 Bytes In-System Programmable EEPROM 512 Bytes Internal SRAM 1.8-5.5V work voltage Support SPI/TWI communication Low power consumption Package included: 10 x ATTINY85 Mini Usb MCU Development Board For Arduino
R 566
See product
South Africa (All cities)
10pcs 5mW 650nm Industrial Laser Tube Metal Laser Sensor Tracking Range Test Description: Dimension: 6.6MM*11.5mm (error /-0.2MM)Output wavelength: 650nmOutput power: I ? 5MWWorking voltage: 2.5V (max)Operating current: ? 20mAStorage temperature: -20 ￢ﾄﾃ to 60 ￢ﾄﾃOperating temperature: -10 ￢ﾄﾃ to 40 ￢ﾄﾃSpot size: 5m light points is less than 15mm (focus adjust)Specifications: Dot spot, continuous outputOperating life: 5,000 hoursDegree: industrial gradePackage included:10 x 5mW 650nm industrial laser sensor
R 400
See product
South Africa (All cities)
10Pcs Soil Hygrometer Humidity Detection Moisture Sensor For Arduino Description: This is a summary of the soil moisture sensor can be used to detect moisture, when the soil is dry, the module outputs a high level, whereas output low. Using this sensor make an automatic watering system, so that your garden plants without people to manage. Operating voltage: 3.3V~5V. Adjustable sensitivity (shown in blue digital potentiometer adjustment) Dual output mode,analog output more accurate. A fixed bolt hole for easy installation. With power indicator (red) and digital switching output indicator (green). Having LM393 comparator chip, stable. Panel PCB Dimension: 3cm x 1.5cm. Soil Probe Dimension: 6cm x 2cm. Cable Length: 21cm. VCC: 3.3V-5V. GND: GND. DO: digital output interface(0 and 1). AO: analog output interface. Instructions for Use: 1. Soil moisture module is most sensitive to the ambient humidity is generally used to detect the moisture content of the soil. 2. Module to reach the threshold value is set in the soil moisture, DO port output high, when the the soil humidity exceeds a set threshold value, the module D0 output low. 3. The digital output D0 can be connected directly with the microcontroller to detect high and low by the microcontroller to detect soil moisture. 4. The digital outputs DO shop relay module can directly drive the buzzer module, which can form a soil moisture alarm equipment. 5. Analog output AO and AD module connected through the AD converter, you can get more precise values of soil moisture. Package Included: 10 x Soil moisture detector module 10 x Probe 10 x 2P Jumper Cable
R 204
See product
South Africa (All cities)
10Pcs 5V-60V To 1.25V-30V LM2576HV DC-DC Step Down Module Feature: Item No: lll-0005 IN +: Input + IN-: input negative OUT+: Output + OUT-: output negative Input voltage range: 5V-60V (Suggestion: 50V or less) Output voltage range: 1.25V-26V Maximum output current: 3A Continuous current: 1.2A (total output power less than 20W) Dimensions: 4.3cm * 3.0cm * 1.2cm (L * W * H) Input: 56V Output: 12V 1A Input: 48V Output: 24V 1A Package included: 10 x DC-DC Step Down Module
R 650
See product
South Africa (All cities)
10Pcs KW12-3 Micro Limit Switch Roller Lever 5A 125V Open/Close Switch Features: Operating temperature: -40°C to 70°C Rated voltage: AC 125V-250V Per weight: 2g Current rating: 5A Size: 20 x 10 x 6mm (L X W X H) PCB Terminals Circuit Board With Roller Lever Limit Working principle: By external mechanical force transmission elements (by pins, buttons, levers, rollers, etc.) will be used to force action on a reed, producing reed instantaneous action when action shifted to the critical point, so moving contact with the fixed contact spring at the end of the action point fast on or off. When the force is removed on the drive components, action reed produce reverse action force transmission element reverse stroke when the action reaches a critical point reed, instantaneous reverse action. Feature: contact spacing is small,short stroke action,according to the power of small,fast-break Application: Apply in A computer mouse, car mouse, automobile electronic products, communications equipment, military products, test instrument, gas water heater, gas burner, small home appliance, microwave oven, electric rice cooker, floating ball supporting equipment, medical equipment, building automation, electric tools, ect. Package included: 10 x Micro roller switch
R 39
See product
South Africa (All cities)
10Pcs Mini 1A Lithium Battery Charging Module Board With USB Interface Description: Charging method: linear charge 1% Charging current: 1A adjustable Charge accuracy: 1.5% Input voltage: 4.5V-5.5V Full charge voltage: 4.2V Charging indicator: Red charging green full charge Charging input interface: Mini USB Working temperature: -10C to +85C Reverse: NO Size: 25 x 19 x 10mm Note: Ampere meter can only be connected to 5V input end of the module. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough. The connection wire should not be too long. Make sure the connect point is good. If the input voltage is too high, like 5.2V, the current will be less than 1000mA, it is normal. It is protection function, Auto-substract the charging current to avoid burn damage to chip. Input reverse has no effect on the chip, but the output (battery terminals) reverse will burn chips. Applications: This module is used for single-or multi-section parallel lithium lithium rechargeable battery, charging from the USB port to take power. Package included: 10 x 1A lithium battery charging module
R 288
See product
South Africa (All cities)
10Pcs DIP Air Pressure Sensor 0-40kPa DIP-6 For Arduino Feature: - This DIP air pressure sensor is suitable for biomedical, meteorology and other fields. The core part is pressure sensor chip which is make by the MEMS pressure technology. - With wide applicable temperature range. - Easy to use and install. - Fits for the following types: 1. Automobile: tire pressure gauge, vehicle-mounted air pump, the MAP sensors, diagnostic equipment, automotive sensors. 2. Industry: air brake switch, portable pressure gauge, such as digital pressure gauge, environment monitor. 3. Medical equipment: patient monitoring and diagnostic equipment, such as blood pressure monitor, medical instrument, and monitor. Specification: - Measuring medium: air - Measuring range: 0-40kPa - Operating temperature range: -40 ??~ + 125 ??/div> - Storage Temperature: -40 ??~ + 150 ??/div> - Humidity: (50% ± 10%) RH - Ambient temperature: (25 ± 1) ??/div> - Medium temperature: (25 ± 1) ??/div> - Output impedance: 4kΩ ~ 6kΩ - Zero output: -15mV~+15mV - Hysteresis: +-0.7%F.S. - Power supply: ≤10V DC or ≤2.0mA DC - Insulation resistance: 100MΩ, 100VDC Package Includeed: 10 x DIP Air Pressure Sensor
R 311
See product
South Africa (All cities)
FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: 1. Input voltage: AC 100V-240V 50-60Hz 2. Output voltage: DC 5V 3. Output current: 2A 4. Output power: 10W 5. Size: 7.2 x 3.4 x 2.5cm 6. Over-voltage protection: Yes 7. Over-current protection: Yes 8. Short circuit protection: Yes 9. IC protection: Yes Package included: 10 x AC-DC 5V 2A 10W switching power module 10pcs AC-DC 5V 2A 10W Switching Power Bare Board Stabilivolt Power Module AC 100-240V To DC 5V 10pcs AC-DC 5V 2A 10W Switching Power Bare Board Stabilivolt Power Module AC 100-240V To DC 5V 10pcs AC-DC 5V 2A 10W Switching Power Bare Board Stabilivolt Power Module AC 100-240V To DC 5V
R 319
See product
South Africa (All cities)
FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: 1. onboard AMS1117-3.3 chip 2. onboard DC input voltage range of 4.75 V to 12 V 3. the onboard 7 * 7 self-locking switch, convenient to control power supply turned on and off during the test 4. the onboard power light, indicating whether the power supply 5. 4-way output voltage interface, convenient connection during the test 6. The board size: 48.5 (mm) x12.5 (mm) Package included: 10 x AMS1117 3.3V Power Supply Module With DC Socket And Switch 10Pcs AMS1117 3.3V Power Supply Module With DC Socket And Switch 10Pcs AMS1117 3.3V Power Supply Module With DC Socket And Switch 10Pcs AMS1117 3.3V Power Supply Module With DC Socket And Switch
R 179
See product
South Africa (All cities)
FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA 10pcs DC-DC 3A Step Down Regulated Power Module Car Charger Dual USB Output 9V/12V/24V/36V To 5V Parameter: Size: 59*21*17mm(length*width*hight) Input: 6V-40V Output: 5V 3A (max) Efficiency: 92% (max) Switching frequency: 150kHz Working temperature: -40°C to +85°C Load capacity: maximum output 3A (can bring two mobile phones at the same time) Scope of application: USB 5V powered devices (such as mobile power, mobile phone, and flat panels) Package included: 10 X Step down regulated power module 10pcs DC-DC 3A Step Down Regulated Power Module Car Charger Dual USB Output 9V/12V/24V/36V To 5V 10pcs DC-DC 3A Step Down Regulated Power Module Car Charger Dual USB Output 9V/12V/24V/36V To 5V
R 449
See product
-
Next →
Visit our blog
Share on Facebook
Share on Twitter