10pcs i2c bit

10Pcs I2C RTC DS1307 AT24C32 Real Time Clock Module For AVR ARM PIC SMD Description: 24C32 32K I2C EEPROM memory Using LIR2032 rechargeable lithium battery with charging circuit Solve the problem of no literacy of the DS1307 with backup battery Support timing 1 year of the DS1307 after fully charged Leads to the DS1307 clock pin provides a clock signal for the microcontroller Other I2C devices can be cascaded Size: 27 x 28 x 8.4mm Note: Because of shipping restrictions, we won't ship battery Package included: 10 x DS1307 module (battery is not included)

10Pcs I2C WiiChuck Nunchuck Small Adapter Shield Module Board For Arduino

Buy 10pcs I2C 8-bit I/O Expander Module PCA8574AD Expansion Board RobotDyn for Ardu for R1,076.78

Buy 10Pcs One Bit WS2812B Serial 5050 Full Color LED Sensor Module for R300.00

Buy 10Pcs One Bit WS2812B Serial 5050 Full Color LED Sensor Module for R204.11

Description:   For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1115 provides 16-bit precision at 860 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differential channels. As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the full range. We like this ADC because it can run from 2V to 5V power/logic, can measure a large range of signals and its super easy to use. It is a great general purpose 16 bit converter. The chip's fairly small so it comes on a breakout board with ferrites to keep the AVDD and AGND quiet. Interfacing is done via I2C. The address can be changed to one of four options (see the datasheet table 5) so you can have up to 4 ADS1115's connected on a single 2-wire I2C bus for 16 single ended inputs.   Feature:   Wide supply range: 2.0V to 5.5V Low current consumption: Continuous Mode: Only 150uA Single-Shot Mode: Auto Shut-Down Programmable data rate: 8SPS to 860SPS Internal Low-drift voltage reference Internal oscillator Internal PGA I2C interface: Pin-Selectable Addresses Four Single-ended or two differential inputs Programmable comparator This board/chip uses I2C 7-bit addresses between 0x48-0x4B, selectable with jumpers Package included: 10 x I2C ADS1115 16 Bit ADC 4 Channel Module

10Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module Description: You’ve always wanted to output analog voltages from a microcontroller, the MCP4725 is the DAC that will let you do it! The CJMCU-MCP4725 is an I2C controlled Digital-to-Analog converter (DAC). A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller. Digital to analog converters are great for sound generation, musical instruments, and many other creative projects! This version of the CJMCU-MCP4725 Breakout fixes a few issues with the board including the IC footprint, the I2C pinout, changes the overall board dimensions to better fit your projects, and a few more minor tweaks. This board breaks out each pin you will need to access and use the MCP4725 including GND and Signal OUT pins for connecting to an oscilloscope or any other device you need to hook up to the board. Also on board are SCL, SDA, VCC, and another GND for your basic I2C pinout. Additionally, if you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this. Feature: 12-bit resolution I2C Interface (Standard, Fast, and High-Speed supported) Small package 2.7V to 5.5V supply Internal EEPROM to store settings Package included: 10 x CJMCU-MCP4725 I2C DAC Breakout Development Board Module

10Pcs CJMCU 1 Bit WS2812 5050 RGB LED Driver Development Board Feature: Votalge: DC 5V Color: RGB Package included: 10 x 1 Bit WS2812 5050 RGB LED Driver Development Board

10Pcs CJMCU 8 Bit WS2812 5050 RGB LED Driver Development Board Feature: Votalge: DC 5V Color: RGB Package included: 10 x CJMCU 8 Bit WS2812 Development Board

10Pcs CJMCU 4 Bit WS2812 5050 RGB LED Driver Development Board Feature: Votalge: DC 5V Color: RGB Size: 15MM X 15MM Pacakge included: 10 x 4 Bit WS2812 5050 RGB LED Driver Development Board

10Pcs CJMCU 7 Bit WS2812 5050 RGB LED Driver Development Board Feature: Radius 11.5mm Package included: 10 x CJMCU 7 Bit WS2812 5050 RGB LED Driver Development Board.

10Pcs NRF24L01+ SI24R1 2.4G Wireless Power Enhanced Communication Receiver Module 10Pcs NRF24L01 SI24R1 2.4G Wireless Power Enhanced Communication Receiver Module Description:NRF24L01 SI24R1 is fully compatible (SPI operation timing, registers, definitions, state diagram), can communicate with each other, support NRF24L01 all communications. Default mode output power of SI24R1 is 2 ~ 3dBm, if you want the output is 7dBm, you should write 1 (NRF24L01 This bit is not used, the default is 0) into the lowest bit register address 0x06 (RF_SETUP). For example, the 01register, 0x061111.Pacakge included:10 x Wireless Power Enhanced Communication Receiver Module

10Pcs Orinigal M27C322-100F1 DIP-42 Mbit 32M EPROMs EPROM Feature: Suitable for microprocessor systems requiring large data or program storage. It is organised as 2 M Words of 16 bit. The pin-out is compatible with a 32 Mbit Mask ROM. The FDIP42W has a transparent lid which allows the user to expose the chip to ultraviolet light to erase the bit pattern. A new pattern can then be written rapidly to the device by following the programming procedure. For applications where the content is programmed only one time and erasure is not required. Specification: Power supply voltage: 5V ± 10% Programming voltage: 12V ± 0.25V Programming practice: 50μs / word Operation access time: 80ns Word width can be configured to 32 mbit mask rom replacement Stand-by current: 100μA Active current: 50mA at 5MHz Package includes: 10 x M27C322-100F1 DIP-42 Mbit EPROM

Description: Brand: CJMCU This is I2C serial interface 16 bit I/O Expander Serial Module Package included: 10 x CJMCU-2317 MCP23017 I2C Serial Interface 16 bit I/O Expander Serial Module

Description: DS1307 I2C real time clock chip (RTC) 24C32 32K I2C EEPROM memory Using CR2032 lithium battery Leads to the DS1307 clock pin provides a clock signal for the microcontroller Other I2C devices can be cascaded Size: 27 x 28 x 8.4mm Package included: 10 x DS1307 real time clock module