Rgb led

If you've ever wanted to add an unconventional display to your project, you've no doubt come across the magic that is RGB LEDs. This ring consists of 12 of these super (and when mean SUPER) bright RGB LEDs placed into a ring and integrated with the ubiquitous one-wire WS2812 controller. All you need to do is download the easy-to-use AdaFruit Neopixel library for your microcontroller of choices (there's support for Arduino, Teensy and even the ESP8266). This ring is easily able to be powered straight from USB without the need of external power. The great thing about these LED rings, like all WS2812-driven RGB LEDs is that you only need a single pin to write to all your LEDs, as the data out pin of the each LED is connect to the data in pin of the next. Just keep in mind - each LED required 3 bytes of memory (one for each RGB colour), so when driving a large number of RGB LEDs, memory on the lower-spec side tends to become an issue. You'll also need a logic-level converter if your microcontroller doesn't use 5V logic. Power requirements Pay careful attention when driving a large number of these at full power. According to our measurements, each RGB LED uses about 30mA when driven at its maximum, although the datasheet specifies up to 60mA.  If you're going to be driving more than one ring, you'll need to replace the USB power with an alternative supply 5V with the required current: Required current = Number of LEDs  x 30mA OR Required current (extra safe) = Number of LEDS x 60mA. Hookup There are two extra steps that you should take in order to ensure your RGB LED Ring is protected. Place a 220-1000uF capacitor over the VCC and GND pin of the LEDs. This is to protect any voltage spikes from accidentally damaging them. Place a 500Ohm resistor (or thereabouts) between the Data In pin and your microcontroller. This is to prevent any noise interfering with the data signal. Documentation WS2812 Datasheet

This wireless remote control for RGB LEDs (strips, bulbs) has a remote control distance up to 30 meters and a 2.4GHz Touch control - an all in one RGB LED controller. Control Your LEDs With the wirless remote control of RGB Leds, you can change the color and mode for LED strips and bulbs. This universal remote can work with many different types of LEDs so long as they are capable of switching colors. Use it at your nightclub, bar, home, theatre, store, shop, convention, event, party, exhibition or show. It has a control distance of up to 30 meters plus a 2.4GHz touch pad, making it an easy to use, all in one RGB LED controller. At a Glance... Wireless RGB Works For Many LEDs Distance up to 30 Meters 2.4GHz Touch Screen Manufacturer Specifications Controller Working Voltage: DC 12V ~ 24V RGB Colors Maximum Load Per Channel: 6A Total Output Current: 18A Output Connection: Common Anode (+) Control Distance: 30 Meters Remote Distance: 30 Meters Power: 2x AAA battery Material: ABS LED Control Dimensions LED Control Dimensions: 85x43x22mm (L x W x D) LED Control Weight: 44g Touch RF Remote Dimensions Touch RF Remote Dimensions: 110x52x20mm (L x W x D) Touch RF Remote Weight: 47g Product Notes Can be used with a large variety of LED Lights. Batteries not included. Package Contents LED Control + Touch RF Remote User Manual

Buy RGB LED Video Lights, VIJIM VL196 RGB Led Mini Video Light with Honeycomb Frame, Soft Light with Bui for R2,295.00

SELECTED OPTION: PLUG: USPLUG CLICK HERE for more options in this item. Specifications: Shell Color: Black Material: Plastic Control Mode: Auto Light Source: 6+3led (RGB 3 in 1) Plug: EU/US plug Voltage: AC90-265V Size: 11cm x 4.5cm   Feature: -Mini size with bright and wide range RGB disco ball, super bright RGB LEDs inside Mini rotating magic ball,360° lighting coverage. -It is a very lively DJ Stage light and perfect for parties and garden get-togethers. -Lighting for disco,karaoke,DJ,party,wedding,christmas,halloween,living room,bedroom.   Package Included: 1x RGB LED Stage Light 1x EU/US Plug  (we will sent adapter according to your country.)

SELECTED OPTION: PLUG: EUPLUG CLICK HERE for more options in this item. Specifications: Shell Color: Black Material: Plastic Control Mode: Auto Light Source: 6+3led (RGB 3 in 1) Plug: EU/US plug Voltage: AC90-265V Size: 11cm x 4.5cm   Feature: -Mini size with bright and wide range RGB disco ball, super bright RGB LEDs inside Mini rotating magic ball,360° lighting coverage. -It is a very lively DJ Stage light and perfect for parties and garden get-togethers. -Lighting for disco,karaoke,DJ,party,wedding,christmas,halloween,living room,bedroom.   Package Included: 1x RGB LED Stage Light 1x EU/US Plug  (we will sent adapter according to your country.)

Buy RGB Led Strip Lights GLIME 10m Led Strips with App Controlled & Music Sync 5050 Fle... (LENGTH: 10M) for R756.00

Buy RGB LED Controller with 21-keys RF Remote Controller for WS2812B WS2811 LED Strip... for R209.00

Buy RGB LED DRIVER 8x8 WITH FTDI BOARD 6PIN & CABLES KT0045 for R529.07

Buy RGB LED Stage Light Lamp For Party With bluetooth Speaker Auto Voice Control...-(Plug US Plug) for R389.00

Buy RGB LED Stage Light Bluetooth Audio Auto/Sound Control Show Party Club Lighting...-(Plug EU Plug) for R539.00

Buy RGB LED Ring Light MJ33 33cm 13-inch with Phone Clip for R599.00

Buy RGB Led Video Light CRI Full Color Lighting Effect K Adjustable Stepless Dimming for Camera Photo... for R2,549.00

Buy RGB LED Car Strip Lights and Interior Remote Control Q-CD52 for R195.50

Buy RGB LED Light Strip bluetooth APP+Remote+Voice Control Ceiling 5050 Background (LENGTH: 1M-2PCS) for R246.57

Buy RGB LED Colorful Stage Lamp Yellow Shell Spot Light for Disco KTV Party AC110-220V (COLOR.: GREEN) for R191.78

Buy RGB LED STRIP LIGHTS 5M BLUE / Stock from 6 Pcs or more for R89.00

Buy RGB LED MultiColour Floodlight: 10W 220V with IR Remote Control. Collections are allowed. for R195.00

RGB LED CONTROLLER; 12VDC; 5A PER CHANNEL; RS232/TTL INTERFACE; WINDOWS SOFTWARE FOR CUSTOM SEQUENCES ETC; BOARDS CAN BE DAISY CHAINED

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA CJMCU 61 Bit WS2812 5050 RGB LED Driver Development Board Description: This 61 Bit LED Board is Composition by 24 Bit, 16 Bit, 12 Bit, 8 Bit and 1 Bit Color: RGB 24Bit: Outer diameter 66mm, 54mm inner diameter 16Bit: Outer diameter 44mm, 32.6mm inner diameter 12Bit: Outer diameter 38.4mm, 27mm inner diameter 8Bit: Outer radius of 2 x 28mm, an inner radius of 2 x 8mm Package included: 1 x CJMCU 61 Bit WS2812 5050 RGB LED Driver Development Board CJMCU 61 Bit WS2812 5050 RGB LED Driver Development Board CJMCU 61 Bit WS2812 5050 RGB LED Driver Development Board CJMCU 61 Bit WS2812 5050 RGB LED Driver Development Board

RF REMOTE CONTROL: This LED strip is using RF remote control, control distance up to 5-10m. More sensitive than infrared remote control Upgraded Version LED: 100% RXMENT ORIGINAL New Generation 5050 RGB LED, continuous 10 Meters/ roll, 24 voltages, Brighter than 12v LED light strip. Ideal for LED ceiling light, LED under cabinet lighting and TV LED backlight What You Get: Complete led light strip kit, including: Rxment 10 meters continuous RGB light strip, 24V,3A Power Supply, RF Mini Controller, Remotes controller. Our worry-free 18-month and friendly customer service. Expensive Materials: Using upgraded adhesive 3M backing, super viscosity and easy installation. Double layer copper, twice costs than other single layer copper LED light strips in the market. Upgraded Color: Not only has basic RGB(Red,Green,Blue),16 multi-colored options for creating romantic atmosphere, but also has Pure White for illumination purpose. No color difference among the whole strips ! You can set it to red led strip, white led strip or green led light strip, etc,. Technical Parameters: Working Voltage: 24V LED Type: 5050 SMD LED LED Quantity: High-brightness 300 quality LEDs Color: Multiple Colors Selection Strip Length: 10 Meters/ roll (32.8 ft) Strip Width: 10mm Color Rendering Index (CRI): Ra85+ Working Tempreture:-20 to 50 Beam angle: 120 degrees Lifespan: 36,000Hrs+ Usage: Indoor use only Package Contents: 1 x 10m 300 LEDs Strip 1 x Remote Controller 1 x RF Mini Controller 1 x 24V,3A Power Supply 1 x Controller Operation Instructions

WS2812 5050 RGB LED RGB LED Ring 16Bit For Arduino Intelligent reverse polarity protection, power supply reverse polarity will not damage the IC. IC control circuit and a power LED spot light utility. Control circuit chip with RGB components in a package in 5050, to form a complete external control pixels. Built-in signal shaping circuit, any one pixel after receiving the signal through the waveform shaping and then output to ensure line waveform distortion will not accumulate. Built-in power-on reset and brown-out reset circuit. Tri-chromatic color of each pixel can realize 256 highlighted, complete 16777216 colors of all true color display, the scanning frequency is not less than 400Hz/s. Serial cascade interface, through a signal line to complete the receiving and decoding of data. Transfer transmission distance between any two points in less than 5 meters without any additional circuitry. When the refresh rate of 30 frames/sec, cascading number of not less than 1024 points. data transmission speeds of up to 800Kbps. The colour of the light highly consistent, cost-effective. Specifications: Outer diameter: 66mm Inner diameter: 53mm Net Weight: 7g This item is available in stock and is not drop shipped. This avoids delays, customs charges and extra VAT.

Color Changing This RGB Led strips lights set will change colors and speed automatically and periodically. It has not only RGB(Red,Green,Blue),16 multicolored options, but also has DIY selection to create your great led mood lighting. LED StripsLed strip lighting has 150 RGB 5050 SMD Leds in 16.4ft with dimmer and brightness controls. The strip is non-waterproof, which is designed to be used indoor. Superior & Safe Material Using double layer copper on PCB board to keep the mixed colors more even. Led IR remote controller has over charging, short circuit protection and memory function. Power Supply is under safe value for adults and kids. Easy Installation & Use Led tape lights can be cut between every 3 leds. 3M self-adhesive tape can be fit on any dry and flat surface. Flexible to install anywhere you want. Worry-Free MINGER led strip lights include 90 Days 100% Satisfaction and 1 year Warrany. Our friendly customer service is always stand behind our product and reply all email within 24 hours.

Description DotStar High Density 8x8 Grid - 64 RGB LED Pixel Matrix Do not eat this LED grid just because it is so colorful and bite-sized! This is the tiniest little LED grid we could make, with 64 full RGB color pixels in a square that is only 1" by 1" square (thats 25.4mm x 25.4mm for you metric-lovers). Arranged in an 8x8 matrix, each pixel is individually addressable: like NeoPixels, DotStar LEDs have an embedded microcontroller inside the LED. You can set the color/brightness of each LED to 24-bit color (8 bits each red green and blue). Wiring it up is easy: there are two 4-pad connection ports on the back. Solder wires to the input port (+5V GND ClockIn and DataIn) and provide 5VDC to the +5V and ground pins, then connect the CIN/DIN pin to your microcontroller.  Quick Specs Product Dimensions: 36.0mm x 25.5mm x 2.6mm Product Weight: 3.0g Resources Product Tutorial Product Page Shipping List 1 x Adafruit DotStar High Density 8x8 Grid - 64 RGB LED Pixel Matrix More Products View More Products

    The 5V usb RGB led light strip c an be powered by any device with a 5V DC output /USB port, such as your power bank, desktop computer, laptop, your phone charger & adapter. It Adds ambient backlighting to any TV/Monitor to reduce eye fatigue and increases image clarity.   Specifications: Input voltage: DC 5v LED type: 5050 RGB Strip length: 2 meter Controller: 24 key IR mini controller Strip light IP Rating: IP65 Package includes: 1 x 5V usb rgb led light strip with controller 1m 1 x Led controller to USB  1 x Remote

Cube4 2x10W Quad LED+64 RGB LED DMX display This Cube4 multicolored LED effect light combines two effects in one fixture featuring 10 DMX channels. The in the center mounted 2x 10W Quad LEDs produce multi-colored effects and animations flowing across the room, while the 4-sided derby effect with 64 RGB LEDs floods the dancefloor with rotating, multi-colored beams. The effects are controllable, producing pre-programmed light shows, or can be operated simultaneously. The product is a "must"  for using in any show. 2x 10W LED Quad and 64 RGB bright LEDs 10 DMX channels Control: DMX, Master/Slave, Sound active, Auto Display and control panel Built-in microphone Sensitivity control Pre-programmed shows Linking in master/slave mode Input/output via 3-pin XLR   Power 50W DMX channels 10 LEDs 2x 10W LED Quad + 64x RGBAW (16x Red, 16x Green, 16x Blue, 8x Amber, 8x White) Power Vac / 50Hz Size 277 x 277 x 320mm Weight 4kg  

The control circuit and the LED share the only power source. Built-in electric reset circuit and power lost reset circuit. all reshaping circuit, after wave reshaping to the next driver, ensure wave-form distortion not accumulate. Each pixel of the three primary color?can achieve 256 brightness display completed 16777216 color full color display, and scan frequency not less than 400Hz/s. Full-color module, Full color soft lights a lamp strip. LED decorative lighting, Indoor/outdoor LED video irregular screen. Features: 100% Brand new and high quality!! The control circuit and the LED share the only power source. Control circuit and RGB chip are integrated in a package of 5050 components, form a complete control of pixel point. Built-in sign al reshaping circuit, after wave reshaping to the next driver, ensure wave-form distortion not accumulate. Built-in electric reset circuit and power lost reset circuit. Each pixel of the three primary color£can achieve 256 brightness display completed 16777216 color full color display, and scan frequency not less than 400Hz/s. Cascading port transmission signal by single line Any two point the distance more than 5m transmission signal without any increase circuit. When the refresh rate is 30fps, cascade number are not less than1024 points. Send data at speeds of 800Kbps. The color of the light were highly consistent, cost-effective. Applications: Full-color module, Full color soft lights a lamp strip. LED decorative lighting, Indoor/outdoor LED video irregular screen. Package includes: 1 *16-Bit 5050 RGB LED Lamp Panel

Estimated delivery time: working days (Imported from the UK) - T&C's Apply Please note that all Christmas gift orders need to be placed before the 14th of November to ensure that they are delivered to you in time. This item includes free delivery within South Africa. The RGB3C is a basic 3-channel RGB lED controller. It was designed to control any standard 3 channel RGB fixture where channel 1 is Red, channel 2 is Green and channel 3 is Blue. All lED fixtures must be set to run in DMX mode and be addressed to DMX channel 1. The units control panel includes nine direct access "Static Color" buttons, which contain pre-programmed color presets, 3 manual RGB faders so a desired color could be set on the fly, a Program select button which allows for 7 static colors and 10 chase programs to be accessed via the program select fader, a Sound Active button which activates the 10 chase programs to randomly sequence via an internal microphone, a Auto run button also activates the 10 chase programs to randomly sequence while the speed of the chases can be controlled via the Speed fader, a Hold button pauses the current scene and will remain locked in even when power to the controller is switched off and on, and finally a Blackout button to bring all values to zero so there is no output going to your fixtures. It's the ideal control solution for D.J.'s, small night Clubs, and bars that want a simple lED controller to run the show. Tech Specs:. - DMX output connector: 3-pin XlR. - Power In: 9-12V 300mA (Included). - Power consumption: 3.6 Watts. - Size: 22 x 14 x 6.3cm. - Weight: 0.8kg.

3Pcs CJMCU 4 x 4 Bit WS2812 5050 RGB LED Driver Development Board Feature: Votalge: DC 5V Color: RGB Size: 30MM X 30MM  (Error in 1MM-2MM) Pacakge included: 3 x 4 x 4 Bit WS2812 5050 RGB LED Driver Development Board

10Pcs CJMCU 1 Bit WS2812 5050 RGB LED Driver Development Board Feature: Votalge: DC 5V Color: RGB Package included: 10 x 1 Bit WS2812 5050 RGB LED Driver Development Board

OPTIONS: EU plug: 10 Available. US plug: 9 Available. Specification: Power: 4W LED Quantity: 4pcs Plug: US plug, EU plug Input: US plug 100-120V, EU plug 210-240V Output: 12V 300A Protection Level: IP55 Irradiation Distance: 5~8m LED Color: RGB (red, green, blue, white) Projector Light Dimension: Approx. 6.8x13x8.2cm/ 2.68x5.12x3.23 in Base Diameter: Approx. 8.5cm/ 3.35 in Power Cable Length: Approx. 135cm/ 53.15 in Material: ABS (Acrylonitrile Butadiene Styrene) Gobo Card Quantity: 4pcs Features: 1.Safe to use, no laser, no harm to eyes compared to laser projection lighting 2.RGB LED beads project bright and clear pattern, can project these slowlyrotating patterns on wall, building, stage, dance floor or any flat surface. 3.Light head is 360 degrees rotatable, light includes a base, it can be directly placed on a table/ desk and other flat places, or even installed on the ground/ wall with screw (screw is not included), easy to install. 4.Great for Christmas, New Year, Halloween, birthday party and holiday decoration, add charming atmosphere to bedroom, living room, stage, club, KTV, etc. Package Included: 1 x LED Projector Light 4 x Gobo Cards Note: Send an adapter according to your country.